Possible Configurations; File Settings - Hitachi G800 Quick Start

4
Run the Initial Startup Wizard
The following procedure describes how to connect to the SVP using Remote Desktop Connection (RDC).
You can also connect using Storage Device List (refer to the Hardware Installation and Reference Guide).
1. Con gure the PC to use an IP address of
10.0.0.xxx, where xxx = 1-99 or 101-254,
and a subnet mask of 255.255.255.0.
2. Run RDC:
a. Click Start > All Programs >
Accessories > Remote Desktop
Connection.
b. At the Remote Desktop Connection
window:
• In the Computer eld, enter the SVP
IP address.
• At the bottom, click Show Options.
In the User Name eld, type
SVP-PC\SVP.
• Click Connect.
c. At the next screen, enter the password
and click the right arrow icon to connect
to the SVP.
If prompted that the identity of the
5
Perform the Initial Setup
The steps for accomplishing a successful
initial setup depend on how your storage
system is configured. There are two

possible configurations:

• Block setup (use RDC)
• VSP G800 and VSP F800 with NAS
Modules setup (use the maintenance
utility first to configure block settings,
and then use NAS Manager to configure

file settings)

Block Setup Only (No NAS Modules)
1. In the Remote Desktop Connection window, click
Start > All Programs > Hitachi Device Manager -
Storage Navigator > StorageDeviceList.
2. Click the registered storage system icon.
3. Log in to Device Manager - Storage Navigator.
4. Launch Maintenance Utility.
5. If prompted, select Continue to this website.
6. In the left pane, under Menu, click Initial Setup
Wizard.
7. At the rst screen, enter the storage system name,
contact, and location. Click Apply and Next.
8. At the next screen, con gure the system date and
time.
9. Click Apply.
10. Set the SVP date, time, and time zone to the local
time using the Windows Control Panel.
remote computer cannot be veri ed,
click Yes to continue.
3. In the Remote Desktop Connection
window:
a. Click Start > All Programs >
Hitachi Device Manager -
Storage Navigator.
b. Right-click Initial Startup and click
Run as administrator.
c. At the bottom of the Initial Startup
Tool window, click Start Setup .
d. When a message about checking the
initial environment appears, click OK.
4. Complete the Initial Startup elds.
5. Click Apply.
6. When Initial Startup is complete,
click Close, and then click Confirm.
The SVP reboots automatically.
Rebooting takes 5 to 10 minutes.
NOTE
Some parameters must be obtained from the customer
NOTE
before performing the Initial Startup Wizard and initial setup.
Initial Startup Tool
Initial Startup
Default Account (maintenance)
New Password
Re-enter New Password
Network Setting
IPv4 Configuration:
Storage System Address
CTL1:
CTL2:
Subnet Mask:
Default Gateway:
DNS Server 1:
DNS Server 2:
DNS Server 3:
IPv6 Configuration: Enable
Disable
7. If you did not connect your IP network
(switch) to the LAN1 port on the SVP, do so
now.
8. For block storage systems, leave the
window open and perform the block setup
for initial setup. Otherwise, close the
window and perform the initial setup for le
or VSP G800 with NAS modules.
If you will use advanced Hitachi software applications, refer to the shared
memory section in the Hardware Installation and Reference Guide to see whether
additional shared memory must be installed.
After performing the initial setup, you can remove the cables from SVP
ports LAN3 and LAN4, and connect the cables to customer-supplied
switches on the network. For more information, see the Service Processor
Technical Reference (FE-94HM8036).
Which window do you want to open?
Maintenance Utility
NAS Manager
Open the window you choose this time
at the next access.
VSP G800 and VSP F800
with NAS Modules
• Use NAS Manager to set link aggregation, IP
routing, directory service, and create system drives.
• Verify that external DNS, WINS, NIS, NTP, or SMTP
servers are running normally.
• If you use a rewall, open port 25.
1. In a web browser, type https://<unified
management IP address>:20443 and press
Enter.
2. When prompted about which window to open, click
and then complete the
Maintenance Utility
settings for block operation.
3. Log out, and then repeat step 1. When
prompted about which window to open, click
and then complete the settings
NAS Manager
for le operation.
SVP Address
Apply
Cancel