Page 1 USER MANUAL PA-6225 15” Waterproof True Flat Touch POS Terminal Powered by Intel Celeron ® ® J1900 Quad-Core PA-6225...
Page 2 PA-6225 POS System COPYRIGHT NOTICE & TRADEMARK All trademarks and registered trademarks mentioned herein are the property of their respective owners. This manual is copyrighted in August 2017. You may not reproduce or transmit in any form or by any means, electronic, or mechanical, including photocopying and recording.
Page 3 FCC NOTICE This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
Page 4: Table Of Contents
Contents TABLE OF CONTENTS CHAPTER 1 INTRODUCTION About This Manual ................2 POS System Specification ..............3 System Specifications ............... 8 Safety Precautions ................16 CHAPTER 2 SYSTEM CONFIGURATION System External I/O Port & Pin Assignment........18 Power Button, Ports, Connectors and Jumpers ....... 19 2-2-1 Power Button ..............
Page 5 Contents 2-4-12 Inverter Connectors ............34 2-4-13 Power Button Connectors ..........35 2-4-14 LED Backlight Power Control Selection ......35 2-4-15 LED Backlight Power Connector ........36 2-4-16 Panel Resolution Selection ..........36 2-4-17 LVDS Connector............... 37 2-4-18 Touch Panel Connectors ........... 37 2-4-19 Touch Panel Signal Interface Selection......
Page 6 Contents 2-5-3-6 Terminal Assignment Connector ......59 VFD Board Component Locations & Pin Assignment ....60 2-6-1 VFD Board: MB-4103, LD720 ......... 60 2-6-1-1 Power Switch Selection........61 2-6-1-2 RS-232 Serial Interface Connector ..... 61 MSR Board Component Locations & Pin Assignment ....62 2-7-1 ID-TECH ................
Page 7 Contents 3-3-4 Cash Drawer ..............150 3-3-5 API Function ..............151 3-3-6 Cash Drawer Function ............. 152 BIOS Operation ................153 3-4-1 Introduction ..............153 3-4-2 Accessing Setup Utility ........... 155 3-4-3 Main… ................158 3-4-4 Advanced ................ 160 3-4-5 Chipset ................
Page 8 CHAPTER INTRODUCTION This chapter gives you the information for the PA-6225. It also outlines the system specifications. The following topics are included:  About This Manual  POS System Illustration  System Specifications  Safety precautions Experienced users can jump to Chapter 2 starting page 17 for a quick start.
Page 9: About This Manual
Chapter 1 Introduction 1-1. ABOUT THIS MANUAL Thank you for purchasing our PA-6225 Series System. The PA-6225 is an updated system designed to be comparable with the highest performance of IBM AT personal computers. The PA-6225 provides faster processing speed, greater expandability and can handle more tasks than before.
Page 10: Pos System Specification
Chapter 1 Introduction 1-2. POS SYSTEM ILLUSTRATION 15” LCD & Touchscreen HDD & its cover Rotatable part for Panel PC (Optional) Vertical Module: MSR & i-Button Indicator Stand Cable Cover Front View Rear View PA-6225 SERIES USER MANUAL Page 3...
Page 11 Chapter 1 Introduction Top View Side View 45° Unit: mm With printer Front View Side View 50° 57.47 182.27 239.74 PA-6225 SERIES USER MANUAL Page 4...
Page 12 Chapter 1 Introduction Printer Opened 50° Unit: mm PA-6225 SERIES USER MANUAL Page 5...
Page 13 Chapter 1 Introduction Caution: Please refer to the pictures below to close the printer door properly. PA-6225 SERIES USER MANUAL Page 6...
Page 14 Chapter 1 Introduction Small stand type Front View Rear View Side View Quarter View 45° Unit: mm PA-6225 SERIES USER MANUAL Page 7...
Page 15: System Specifications
AMI SPI BIOS, 8 Mbits with VGA BIOS RTC Accuracy 3 days ± 3 seconds System Weight With power adapter approx. 7 kg Dimension (W x H x D) 377mm x 318mm x 240mm 24~30˚ Viewing Angel PA-6225 SERIES USER MANUAL Page 8...
Page 16 0.15~80MHz, 3Vrms, 80% AM, 1kHz IEC 61000-4-8 PFMF 50Hz, 1A/m  IEC 61000-4-11 Voltage Dips > 95% reduction for 0.5 periods  30% reduction for 25 periods Voltage Interruptions > 95% reduction for 250 periods PA-6225 SERIES USER MANUAL Page 9...
Page 17  10.4” LCD (Resolution: 1024 x 768 or 800 x 600)  Interface: RS-232C Baud Rate: 9600/19200 bps Customer Display  Placement: 20 columns and 2 lines, each column is 5 x 7 dots  Brightness: cd/m  Dimensions: 107.2 18.2 PA-6225 SERIES USER MANUAL Page 10...
Page 18 2inch 432 dots; Printable dots per line 3inch 576 dots Maximum print speed 2inch 200 mm/s; 3inch 170 mm/s Print width 2inch 54 mm; 3inch 72mm Paper width 2inch 58 +0/-1 mm; 3inch 80 +0/-1 mm PA-6225 SERIES USER MANUAL Page 11...
Page 19 CP-1251, CP-1252, CP-1253, CP-1254, CP-1257, Katakana  KANJI JAPANESE (SHIFT-JIS) Code, TRADITIONAL CHINESE Code  International Characters USA, FRANCE, GERMANY, UK, DENMARK I, SWDEN, ITALY, SPAIN I, JAPAN, NORWAY, DENMARK II, SPAIN II, LATIN AMERICA, KOREA, RUSSIA, SLAVONIC PA-6225 SERIES USER MANUAL Page 12...
Page 20 Chapter 1 Introduction RAID:RAID 1 PA-6225 SERIES USER MANUAL Page 13...
Page 21 Chapter 1 Introduction PA-6225 SERIES USER MANUAL Page 14...
Page 22 Chapter 1 Introduction RAID Regulation PA-6225 SERIES USER MANUAL Page 15...
Page 23: Safety Precautions
(3) Avoid exposure to sunlight for a long period of time (for example, in a closed car in summer time. Also avoid the system from any heating device.). Or do not use the PA-6225 when it has been left outdoors in a cold winter day.
Page 24  External I/O Port Pin Assignment  How to Set Jumpers  Component Locations & Jumper Settings - Main Board - Printer Board (peripheral device) - VFD Board (peripheral device) - MSR Board (peripheral device)  Page 17 PA-6225 SERIES USER S MANUAL...
Page 25: System External I/O Port & Pin Assignment
Note 2: UPS function is supported for PA-6225RC-E0B and PA-6225RC-F0B only. Note 3: One RJ45 to DB9 cable (P/N: 27-024-27403111) is provided with the system. Note 4: The Printer Power port is provided when the system is purchased with Printer. PA-6225 SERIES USER MANUAL Page 18...
Page 26: Power Button, Ports, Connectors And Jumpers
DC-IN: DC Power-In Port (rear I/O) PIN ASSIGNMENT PIN ASSIGNMENT +24V +24V DC-IN 2-2-3. VGA Port VGA1: VGA Port, D-Sub 15-pin (rear I/O) PIN ASSIGNMENT PIN ASSIGNMENT GREEN VGA1 BLUE DDCA DATA HSYNC VSYNC DDCA CLK PA-6225 SERIES USER MANUAL Page 19...
Page 27: Com Ports
Right Side LED Yellow Color Blinking LAN Message Active No LAN Message Active Left Side LED Green Color On 10/100Mbps LAN Speed Indicator Orange Color on Giga LAN Speed Indicator No LAN switch/ hub connected. PA-6225 SERIES USER MANUAL Page 20...
Page 28: Cash Drawer Port (Optional)
2-2-7. 2 Display Power Port (Optional) DIS PWR: Second Display Power port (Rear I/O) ASSIGNMENT DIS PWR +12V +12V 2-2-8. RAID Power Port (Optional) RAID PWR: RAID Power port (Rear I/O) ASSIGNMENT RAID PWR PA-6225 SERIES USER MANUAL Page 21...
Page 29: Usb Ports
USB8 ESATA1 2-2-10. Printer Power Port (Optional) PRT PWR: DC24V power supply for the stand-printer PIN ASSIGNMENT +24V PRT PWR 2-2-11. UPS Power Port (Optional) UPS: UPS Power port (Rear I/O) ASSIGNMENT +24V +24V PA-6225 SERIES USER MANUAL Page 22...
Page 30: Mainboard Component Locations & Jumper Settings
Chapter 2 System Configuration 2-3. MAINBOARD COMPONENT LOCATIONS & JUMPER SETTINGS M/B: PB-6822 PB-6822 Main Board Component Locations PA-6225 SERIES USER MANUAL Page 23...
Page 31: How To Set Jumpers
PIN1 & PIN2 to create one setting and shorting. You can either connect PIN2 & PIN3 to create another setting. The same jumper diagrams are applied all through this manual. The figure below shows what the manual diagrams look and what they represent. PA-6225 SERIES USER MANUAL Page 24...
Page 32 Chapter 2 System Configuration Jumper Diagrams Jumper Settings PA-6225 SERIES USER MANUAL Page 25...
Page 33: Com Port Ri & Voltage Selection
3. The voltage of COM port is adjustable by BIOS or jumpers. You can select to adjust the voltage of COM ports either through BIOS or by setting jumpers. DO NOT use these two methods at the same time in case of system error, component damage or serious boot failure. PA-6225 SERIES USER MANUAL Page 26...
Page 34: Com Connectors
2-4-4. i-Button Function Selection JP20, JP21, JP22: i-Button Function Connectors SELECTION JUMPER SETTING JUMPER ILLUSTRATION COM3 (Default) JP20/JP21/JP22/ i-Button* JP20/JP21/JP22/ *COM3 & COM3_1 will not function when jumpers JP20, JP21 & JP22 are set as “i-Button.” PA-6225 SERIES USER MANUAL Page 27...
Page 35: Cash Drawer Control Selection
Method 2: You can split DRW1 into two channels of DRW1-1 & DRW1-2 by using the Y-Cable (option). JP37: Cash Drawer control connector SELECTION JUMPER SETTING JUMPER ILLUSTRATION DRW1-1 & DRW1-2 JP37 GND (Default) JP37 PA-6225 SERIES USER MANUAL Page 28...
Page 36 To exit the Extended Function Mode, writing 0xAA to the EFER is required. Once the chip exits the Extended Function Mode, it is in the normal running mode and is ready to enter the configuration mode. PA-6225 SERIES USER MANUAL Page 29...
Page 37 The DRW2 Port only can function when the optional "Printer Kit" is installed on PA- 3122. The DRW2 signals from the printer board (MB-1030, MB-1011, MB- 1013,PDAC-3100) can be controlled via relevant commands. The DRW2 port is located on the rear I/O panel as shown below: PA-6225 SERIES USER MANUAL Page 30...
Page 38 Chapter 2 System Configuration PA-6225 SERIES USER MANUAL Page 31...
Page 39: Cash Drawer Power Selection
3. The voltage of cash drawer port is adjustable by BIOS or jumpers. You can select to adjust the voltage of COM ports either through BIOS or by setting jumpers. DO NOT use these two methods at the same time in case of system error, component damage or serious boot failure. PA-6225 SERIES USER MANUAL Page 32...
Page 40: Usb Connectors
JP14 & JP15 are set as 1-2 (short) connected. USB6 2-4-8. LED Connectors LED1_1: Power LED connector ASSIGNMENT LED1_1/ 2-4-9. Power for Thermal Printer Connector PRT_PWR1: Power for Thermal Printer Connector PIN ASSIGNMENT VCC24SB PRT_PWR1 VCC24SB PA-6225 SERIES USER MANUAL Page 33...
Page 41: Power Connectors
DC5V_PWR1: DC 5Voltage Provider Connector ASSIGNMENT DC5V_PWR1 2-4-11. External Speaker Connectors SPK1, SPK2: External Speaker Connector ASSIGNMENT SPK1/ SPK_GND SPK2 SPK_OUT 2-4-12. Inverter Connectors JINV4: Inverter connectors PIN ASSIGNMENT +12V +12V JINV4/ BRCTR LVDS_BKLTEN PA-6225 SERIES USER MANUAL Page 34...
Page 42: Power Button Connectors
2-4-13. Power Button Connectors SW1_1, SW1_2: Power Button connectors PIN ASSIGNMENT +3.3V SW1_1 SW1_2 2-4-14. LED Backlight Power Control Selection JP12: LED backlight power control connectors SELECTION JUMPER SETTING JUMPER ILLUSTRATION (Default) JP12 JP12 PA-6225 SERIES USER MANUAL Page 35...
Page 43: Led Backlight Power Connector
JP8: 3-5, 2-4 1024 x 768 JP9:3-5, 4-6 (18 bit) 10.4” JP8: 3-5, 4-6 800 x 600 JP9: 3-5, 4-6 (18bit) 17” 1280 x 1024 JP8: 1-3, 4-6 (24bit Dual) JP9: 1-3, 4-6 (Default) PA-6225 SERIES USER MANUAL Page 36...
Page 44: Lvds Connector
LVDS_A2_D- LVDS_A1_D+ LVDS_A1_D- LVDS_A0_D+ LVDS_A0_D- LVDS_A3_D+ LVDS_A3_D- LVDS_VCC LVDS_VCC 2-4-18. Touch Panel Connector TOUCH1, TOUCH2: Touch panel connector ASSIGNMENT LR (Low Right) LL (Low Left) TOUCH1 Probe UR (Up Right) UL (Up Left) TOUCH2 PA-6225 SERIES USER MANUAL Page 37...
Page 45: Touch Panel Signal Interface Selection
To clear CMOS data, you must power off the computer and set the jumper to Note: “Clear CMOS” as shown above. After five to six seconds, set the jumper back to “Normal” and power on the computer. PA-6225 SERIES USER MANUAL Page 38...
Page 46: Msr/Card Reader Connectors
SATA1, SATA2: Serial ATA connectors ASSIGNMENT SATA1/ SATA2/ Note: SATA1 only supports the optional RAID function on board. JPWR_4P1, JPWR_4P2: Serial ATA power connectors ASSIGNMENT JPWR_4P1/ JPWR_4P2/ VCC12 Note: JPWR_4P1 only supports the optional RAID function on board PA-6225 SERIES USER MANUAL Page 39...
Page 47: Printer Connector
Chapter 2 System Configuration 2-4-23. Printer Connector LPT1 LPT1: Printer connector ASSIGNMENT ASSIGNMENT STBJ ALFJ PDR0 ERRJ PDR1 PAR_INITJ PDR2 SLCTINJ PDR3 PDR4 PDR5 PDR6 PDR7 ACKJ BUSY SLCTJ PA-6225 SERIES USER MANUAL Page 40...
Page 48: Mini-Pcie / Msata Connector
WAKE# +3.3V SLOT1 Reserved Reserved +1.5V CLKREQ# Reserved Reserved REFCLK1- Reserved REFCLK1+ Reserved Reserved Reserved Reserved Reserved PERST# PERn2 +3.3SB PERp2 +1.5V SMB_CLK PETn2 SMB_DATA PETp2 +3.3V +3.3V Reserved Reserved Reserved +1.5V Reserved +3.3V PA-6225 SERIES USER MANUAL Page 41...
Page 49: Printer Board Component Locations & Pin Assignment
Chapter 2 System Configuration 2-5. PRINTER BOARD COMPONENT LOCATIONS & PIN ASSIGNMENT 2-5-1. Printer Board: PDAC-3100 PDAC-3100 Printer Board Component Locations PA-6225 SERIES USER MANUAL Page 42...
Page 50: Power Supply Connector
Chapter 2 System Configuration 2-5-1-1. Power Supply Connector CN1: Power supply wafer PIN ASSIGNMENT +24V +24V 2-5-1-2. RS-232 Interface Connector CN7: RS-232 interface connector PIN ASSIGNMENT ASSIGNMENT PA-6225 SERIES USER MANUAL Page 43...
Page 51: Auto-Cutter Connector
Auto-cutter motor drive signal 1B-1 Auto-cutter motor drive signal 1B-2 Auto-cutter motor drive signal 1A-1 Auto-cutter motor drive signal 1A-2 Auto-cutter motor drive signal 2-5-1-4. USB Connector CN8: USB Connector PIN ASSIGNMENT PIN ASSIGNMENT Vbus PA-6225 SERIES USER MANUAL Page 44...
Page 52: Thermal Head/Motor/Sensor Connector
Head strobe signal DST3 Head strobe signal 3.3V Logic Power Thermistor GND Thermistor GND Thermistor signal Unused DST2 Head strobe signal DST1 Head strobe signal Head GND Head GND Head GND Head GND Head GND PA-6225 SERIES USER MANUAL Page 45...
Page 53 Power supply of the out-of- paper sensor GND of the platen position/ out-of-paper sensor Signal of the platen position sensor Unused Frame GND Frame GND Unused Motor drive signal Motor drive signal Motor drive signal Motor drive signal PA-6225 SERIES USER MANUAL Page 46...
Page 54: Terminal Assignment Connector
Feed signal RESET Reset signal Status signal Status signal Status signal Status signal Drawer sensor signal Drawer switch signal Drive terminal for the drawer (Vp side) GNDdu Drive terminal for the drawer (GND side) Unused PA-6225 SERIES USER MANUAL Page 47...
Page 55: Printer Board: Mb-1030
Chapter 2 System Configuration 2-5-2. Printer Board: MB-1030 CUT_CN1 COM1 9 10 USB_CN1 24V_CN1 PRINT_CN1 MB-1030 Printer Board Component Locations PA-6225 SERIES USER MANUAL Page 48...
Page 56: Power Supply Connector
Chapter 2 System Configuration 2-5-2-1. Power Supply Connector 24V_CN1: Power Supply Wafer PIN ASSIGNMENT +24V +24V 24V_CN1 2-5-2-2. RS-232 Interface Connector COM1: RS-232 Interface Connector PIN ASSIGNMENT ASSIGNMENT DSR /CTS 9 10 COM1 DTR /RTS PA-6225 SERIES USER MANUAL Page 49...
Page 57: Thermal Head/Motor/Sensor Connector
Head strobe signal DST3 Head strobe signal 3.3V Logic Power Thermistor GND Thermistor GND Thermistor signal Unused DST2 Head strobe signal DST1 Head strobe signal Head GND Head GND Head GND Head GND Head GND PA-6225 SERIES USER MANUAL Page 50...
Page 58 Power supply of the out-of- paper sensor GND of the platen position/ out-of-paper sensor Signal of the platen position sensor Unused Frame GND Frame GND Unused Motor drive signal Motor drive signal Motor drive signal Motor drive signal PA-6225 SERIES USER MANUAL Page 51...
Page 59: Auto-Cutter Connector
Auto-cutter motor drive signal 2-5-2-5. Paper-Near-END Sensor Connector CN2: Paper-near-end sensor connector PIN ASSIGNMENT FUNCTION Power supply of the near end sensor Signal of the near end sensor GND of the near end sensor PA-6225 SERIES USER MANUAL Page 52...
Page 60: Usb Interface Connector
Feed signal RESET Reset signal Status signal Status signal Status signal Status signal Drawer sensor signal Drawer switch signal Drive terminal for the drawer (Vp side) GNDdu Drive terminal for the drawer (GND side) Unused PA-6225 SERIES USER MANUAL Page 53...
Page 61: Printer Board: Mb-1011 & Mb-1013
Chapter 2 System Configuration 2-5-3. Printer Board: MB-1011 & MB-1013 MB-1011 & MB-1013 Printer Board Component Locations PA-6225 SERIES USER MANUAL Page 54...
Page 62: Power Supply Connector
Chapter 2 System Configuration 2-5-3-1. Power Supply Connector CN1: Power supply wafer PIN ASSIGNMENT +24V +24V 2-5-3-2. RS-232 Interface Connector CN7: RS-232 interface connector PIN ASSIGNMENT PIN ASSIGNMENT PA-6225 SERIES USER MANUAL Page 55...
Page 63: Thermal Head/Motor/Sensor Connector
Head strobe signal DST3 Head strobe signal 3.3V Logic Power Thermistor GND Thermistor GND Thermistor signal Unused DST2 Head strobe signal DST1 Head strobe signal Head GND Head GND Head GND Head GND Head GND PA-6225 SERIES USER MANUAL Page 56...
Page 64 Power supply of the out-of- paper sensor GND of the platen position/ out-of-paper sensor Signal of the platen position sensor Unused Frame GND Frame GND Unused Motor drive signal Motor drive signal Motor drive signal Motor drive signal PA-6225 SERIES USER MANUAL Page 57...
Page 65: Auto-Cutter Connector
Auto-cutter motor drive signal 1B-1 Auto-cutter motor drive signal 1B-2 Auto-cutter motor drive signal 1A-1 Auto-cutter motor drive signal 1A-2 Auto-cutter motor drive signal 2-5-3-5. USB Interface Connector CN8: USB interface connector PIN ASSIGNMENT Vbus PA-6225 SERIES USER MANUAL Page 58...
Page 66: Terminal Assignment Connector
Feed signal RESET Reset signal Status signal Status signal Status signal Status signal Drawer sensor signal Drawer switch signal Drive terminal for the drawer (Vp side) GNDdu Drive terminal for the drawer (GND side) Unused PA-6225 SERIES USER MANUAL Page 59...
Page 67: Vfd Board Component Locations & Pin Assignment
Chapter 2 System Configuration 2-6. VFD BOARD COMPONENT LOCATIONS & PIN ASSIGNMENT 2-6-1. VFD Board: MB-4103, LD720 JP12V MB-4103 & LD720 VFD Board Component Locations PA-6225 SERIES USER MANUAL Page 60...
Page 68: Power Switch Selection
Chapter 2 System Configuration 2-6-1-1. Power Switch Selection JP12V: Power Switch Selection SELECTION JUMPER SETTING JUMPER ILLUSTRATION JP12V (Default) JP12V 2-6-1-2. RS-232 Serial Interface Connector CN1: RS-232 serial interface wafer ASSIGNMENT ASSIGNMENT +12V/+5V PA-6225 SERIES USER MANUAL Page 61...
Page 69: Msr Board Component Locations & Pin Assignment
2-7. MSR BOARD COMPONENT LOCATIONS & PIN ASSIGNMENT 2-7-1. ID-TECH ID-TECH MSR Board Component Locations 2-7-1-1. Main Connector ASSIGNMENT ASSIGNMENT Chassis Ground K-CLK (Computer connections) P-CLK K-DATA (Keyboard connections) (Computer connections) P-DATA (Keyboard connections) +5V Vcc PA-6225 SERIES USER MANUAL Page 62...
Page 70: Sysking
2-7-2. SYSKING SYSKING MSR Board Component Locations 2-7-2-1. Main Connector ASSIGNMENT ASSIGNMENT +5V Vcc K-DATA (Host to MSR) K-CLK Host to MSR P-DATA (MSR to Keyboard) P-CLK Signal Ground (MSR to Keyboard) Signal Ground PA-6225 SERIES USER MANUAL Page 63...
Page 71: Mb-3012
MB-3012 MSR Board Component Locations 2-7-3-1. Information Button Reader I_BUTTON1: Information button reader ASSIGNMENT I_B1 I_BUTTON1 2-7-3-2. Output Connector IO1: Output wafer ASSIGNMENT ASSIGNMENT CLK_KB RX_MSR CLK_PC TX_MSR DATA_KB DATA_PC USB_D+_R USB_D-_R CHASSIS GND PA-6225 SERIES USER MANUAL Page 64...
Page 72 CHAPTER SOFTWARE This chapter provides the detailed information of driver utilities and BIOS (Basic Input Output Subsystem) settings for the system. The following topics are included:  Driver ® - Intel Chipset Software Installation Utility - VGA Driver Utility - LAN Driver Utility - Sound Driver Utility - Touchscreen Driver Utility - Fingerprint Driver Utility (Optional)
Page 73: Driver
Chapter 3 Software 3-1. DRIVER 3-1-1. Introduction Enclosed with the PA-6225 Series package is our driver utilities, which comes in a DVD-ROM disc. Driver Folder 1. The setup sequence is "Main Chip -> VGA -> LAN -> SOUND -> TOUCH[Device folder]"...
Page 74: Intel® Chipset Software Installation Utility
10 series, and it should be installed right after the OS installation is completed. Please follow the steps below: Connect the USB DVD-ROM device to PA-6225 and insert the driver disk. Open the “Main Chip” folder where the Chipset driver is located (depending on your OS platform).
Page 75: Vga Driver Utility
Chapter 3 Software 3-1-3. VGA Driver Utility The VGA interface embedded with PA-6225 can support a wide range of display types. You can have dual displays by configuring CRT & LVDS interfaces to work simultaneously. 3-1-3-1. Installing VGA Driver To install the VGA driver, follow the steps below: Connect the USB-DVD ROM device to PA-6225 and insert the driver disk.
Page 76: Sound Driver Utility
OS platform). Click Setup.exe file for driver installation. Follow the on-screen instructions to complete the installation. Once the installation is completed, shut down the system and restart PA-6225 for the changes to take effect. 3-1-6. Touchscreen Driver Utility The touchscreen driver utility can only be installed on Windows POSReady 7 &...
Page 77: Fingerprint Driver Utility
Click Setup.exe file for driver installation. Follow the on-screen instructions to complete the installation. Once the installation is completed, shut down the system and restart PA-6225 for the changes to take effect. 3-1-8. RFID Module Driver Utility (Optional) The RFID driver utility can only be installed on Windows POSReady7 &...
Page 78: Wireless Module Driver Utility (Optional)
Click Setup.exe file for driver installation. Follow the on-screen instructions to complete the installation. Once the installation is completed, shut down the system and restart PA-6225 for the changes to take effect. 3-1-10. For Intel Trusted Execution Engine Interface For POSReady 7 only.
Page 79: Peripheral Devices
The commands lists and driver installation guide for peripheral devices of the system - printer board, VFD and MSR – are explicitly included in this section. 3-2-1. Printer Board: MB-1030 3-2-1-1. Commands Printer Registry Operation Registry Name Default Data Notes BaudRate 115200 BitLength Parity Stop PA-6225 SERIES USER MANUAL Page 72...
Page 80 GS h FS q GS k ESC 2 GS ! GS r ESC 3 GS $ GS v 0 ESC = GS * GS w ESC ? GS ( A ESC @ GS ( K PA-6225 SERIES USER MANUAL Page 73...
Page 81 Kanji Control Commands Other Commands MB-1030 MB-1030 MB-1030 MB-1030 Command Command FS ! ESC i FS & ESC m DC2 ; FS . GS p 1 FS 2 FS C FS S FS W PA-6225 SERIES USER MANUAL Page 74...
Page 82: Commands List
Turn emphasized mode on/off <ESC G> 1B 47 Turn double-strike mode on/off <ESC J> 1B 4A Print and feed paper ◎ <ESC L> 1B 4C Select page mode Ignored <ESC M > 1B 4D Select character font PA-6225 SERIES USER MANUAL Page 75...
Page 83 Select printing position <GS H> 1D 48 characters <GS I> 1D 49 Transmit printer ID Disabled ◎ <GS L> 1D 4C Set left margin Disabled <GS P> 1D 50 Set basic calculated pitch PA-6225 SERIES USER MANUAL Page 76...
Page 84 <FS S> 1C 53 Set Kanji character spacing Turn quadruple-size mode on/off for Kanji <FS W> 1C 57 characters Command classification: Executing : Printer executes the command, which does not then affect the following data. PA-6225 SERIES USER MANUAL Page 77...
Page 85 Prints the data in the print buffer and performs a line feed based on the set line [Description] feed amount.  After execution, makes the top of the line the next print starting position. PA-6225 SERIES USER MANUAL Page 78...
Page 86 Deletes all print data in the currently set print region in page mode.  This command is enabled only in page mode. [Description]  Portions included in the currently set print region are also deleted, even if previously set print region data. PA-6225 SERIES USER MANUAL Page 79...
Page 87 Cover is closed. Cover is open. Not used. Fixed to Off. Not used. Fixed to On. No paper-end stop. Printing stops due to paper end. No error. Error occurs. Not used. Fixed to Off. PA-6225 SERIES USER MANUAL Page 80...
Page 88 Printing stops due to paper near end. Not used. Fixed to On. No paper-end stop. Printing stops due to paper end. No paper-end stop. Printing stops due to paper end. Not used. Fixed to Off. PA-6225 SERIES USER MANUAL Page 81...
Page 89 Prints all buffered data in the print area collectively in page mode.  This command is enabled only in page mode.  Holds the following information after printing. [Description] a. Expanded data b. Character print direction selection in page mode (ESC T) PA-6225 SERIES USER MANUAL Page 82...
Page 90 Emphasized mode not selected. Emphasized mode selected. [Description] Double-height mode not selected Double-height mode selected Double-width mode not selected. Double-width mode selected. Not used. Fixed to Off. Underline mode not selected. Underline mode selected. PA-6225 SERIES USER MANUAL Page 83...
Page 91 67 DPI 101 DPI nL+nH×256 density 8 dot double 67 DPI 203 DPI nL+nH×256 density 24 dot (nL+nH×256) single 203 DPI 101 DPI ×3 density 24 dot (nL+nH×256) double 203 DPI 203 DPI ×3 density PA-6225 SERIES USER MANUAL Page 84...
Page 92 Hex. Decimal 0 ≤ n ≤ 255 [Range] Initial Value n = 34 This command sets the line spacing using a following rule. [Description] Line spacing = n x (vertical or horizontal motion units) PA-6225 SERIES USER MANUAL Page 85...
Page 93 Clears data from the print buffer and sets the printer to its default settings. ESC D n1…nk NUL [Name] Set horizontal tab position ASCII n1...nk NUL [Format] Hex. n1...nk NUL Decimal n1...nk NUL 1 ≤ n ≤ 255 [Range] 0 ≤ k ≤ 32 PA-6225 SERIES USER MANUAL Page 86...
Page 94 ESC J n [Name] Print and feed paper. ASCII ESC J [Format] Hex. Decimal 0 ≤ n ≤ 255 [Range] [Description] This command prints the data in the print buffer and feeds the paper [n X PA-6225 SERIES USER MANUAL Page 87...
Page 95 ESC V :Specify/cancel character 90 degree clockwise rotation b. ESC a :Position alignment c. ESC { :Specify/cancel upside-down printing d. GS W :Set print region width  The following command is ignored in page mode. a. GS (A :Test print PA-6225 SERIES USER MANUAL Page 88...
Page 96 Character font A selected Character font B selected ESC R n [Name] Select an international character set. ASCII ESC R [Format] Hex. Decimal 0 ≤ n ≤ 16 [Range] Initial Value n = 0 PA-6225 SERIES USER MANUAL Page 89...
Page 97 ESC SP :Set character right space amount b. FS S :Set Chinese character space amount c. ESC 2 :Set default line spacing PA-6225 SERIES USER MANUAL Page 90...
Page 98 Bottom to Top Lower Left (B in the figure below) 2, 50 Right to Left Lower Right (C in the figure below) 3, 51 Top to Bottom Upper Right (D in the figure below) [Description] PA-6225 SERIES USER MANUAL Page 91...
Page 99 Vertical direction length = [(dyL + dyH x 256) basic calculated pitch]  (X+Dx-1)<576 (3 inch, basic calculated pitch=1);(X+Dx-1)<432 (2 inch, basic calculated pitch=1)  (Y+Dy-1)<768 (basic calculated pitch=1);  If (horizontal starting position + printing area width) exceeds the printable PA-6225 SERIES USER MANUAL Page 92...
Page 100 This command specifies position alignment for all data in one line in standard mode, using n as follows: Alignment Left alignment [Description] Center alignment Right alignment This command has no effect in page mode. PA-6225 SERIES USER MANUAL Page 93...
Page 101 Selects the paper out detector to stop printing when paper has run out. “0” “1” Function Undefined Undefined Undefined [Description] Undefined Undefined Undefined Paper roll near end detector Invalid Valid Paper roll near end detector Invalid Valid PA-6225 SERIES USER MANUAL Page 94...
Page 102  Sets the print position to the beginning of the next line after printing. [Description]  Paper is fed approximately 150 mm if the [n x basic calculated pitch] exceeds approximately 150 mm (5.9 inches). PA-6225 SERIES USER MANUAL Page 95...
Page 103 Drawer kick on time is set to t1 x 2 ms; off time is set to t2 x 2 ms. Connector Pin 0, 48 Drawer kick connector pin #2 [Description] 1, 49 Drawer kick connector pin #5 PA-6225 SERIES USER MANUAL Page 96...
Page 104 [Description]  This command has no effect in page mode. In page mode, this command is only effective for the setting.  Upside-down printing rotates line data 180 degrees. PA-6225 SERIES USER MANUAL Page 97...
Page 105 1 ≤ (yL + yH ×256) ≤ 96 (0 ≤ yL ≤ 96, yH=0) 0 ≤ d ≤ 255 k = (xL + xH × 256) × (yL + yH × 256) × 8 PA-6225 SERIES USER MANUAL Page 98...
Page 106 (1 ≤ Vertical enlargement ≤ 8, 1 ≤ Horizontal enlargement ≤ 8) [Range] Initial Value n = 0 This command selects the character height and width using bits 0 to 3, and bits 4 to 7 respectively as follows: [Description] PA-6225 SERIES USER MANUAL Page 99...
Page 107 4 times 5 times 6 times 7 times 8 times Table 2 [Enlarged in vertical direction] Decimal Enlargement 1 time(standard) 2 times 3 times 4 times 5 times 6 times 7 times 8 times PA-6225 SERIES USER MANUAL Page 100...
Page 108 Hex. [d1…d(X x Y x 8)] Decimal 1 ≤ X ≤ 54 (for 2 inch) 1 ≤ X ≤ 72 (for 3 inch) [Range] 1 ≤ Y ≤ 96 0 ≤ d ≤ 255 PA-6225 SERIES USER MANUAL Page 101...
Page 109 Decimal {pL+ (pH×256) } = 2 (pL = 2,pH = 0) 0 ≤ n ≤ 2 , 48 ≤ n ≤ 50 [Range] 2 ≤ m ≤ 3 , 50 ≤ m ≤ 51 PA-6225 SERIES USER MANUAL Page 102...
Page 110 {pL+ (pH×256) } = 2 (pL = 2,pH = 0) n = 49 250 ≤ m ≤ 255, 0 ≤ m ≤ 6 Initial Value m = 0 [Description] Sets print density. Print Density PA-6225 SERIES USER MANUAL Page 103...
Page 111  n is effective only when it is the lowest bit. [Description]  Internal characters and download characters are targeted for black and white inverted printing.  This command is effective for ANK and Chinese characters. PA-6225 SERIES USER MANUAL Page 104...
Page 112 MB-1030 System or MP-1060 System [Description] Name Model Name MB-1030 or MP-1060 Serial Number Depends on the serial number Chinese Taiwan Language Characters: TW_BIG5 Character Types Japanese Language Characters: JP_SJIS Chinese Language Characters: CN_GB2312 Korean Language Characters: KO_EUC-KR PA-6225 SERIES USER MANUAL Page 105...
Page 113 = 0: Returns the vertical basic calculated pitch to its default value. GS V m [Name] Cut paper. ASCII m ( n ) [Format] Hex. m ( n ) Decimal m ( n ) m = 0,1,48,49,65,66 0 ≤ n ≤ 255 [Range] PA-6225 SERIES USER MANUAL Page 106...
Page 114 This sets the position moved from the current position to [(nL + nH x 256) x basic calculated pitch] for the next data expanding starting position.  When not in page mode, this command is ignored. PA-6225 SERIES USER MANUAL Page 107...
Page 115 Cover is open Not used. Fixed to On On-line Off-line Drawer kick-out connector pin 3 is LOW Drawer kick-out connector pin 3 is HIGH Not used. Fixed to Off Not used. Fixed to Off PA-6225 SERIES USER MANUAL Page 108...
Page 116 Black mark sensor status Not used. Fixed to Off Not used. Fixed to Off Not used. Fixed to On Not used. Fixed to On Not used. Fixed to On Not used. Fixed to On PA-6225 SERIES USER MANUAL Page 109...
Page 117 1. 0 ≤ m ≤ 6 The definition region of k and d differ according to the bar code type. [Range] 2. 65 ≤ m ≤ 73 The definition region of n and d differ according to the bar code type. PA-6225 SERIES USER MANUAL Page 110...
Page 118 48 ≤ d ≤ 57, 65 ≤ d ≤ 68, CODABAR 36, 43, 45, 46, 47, 58 1 ≤ n ≤ 255 0 ≤ d ≤ 127 CODE93 2 ≤ n ≤ 255 0 ≤ d ≤ 127 CODE128 PA-6225 SERIES USER MANUAL Page 111...
Page 119 Print raster bit image. ASCII yH d1...dk [Format] Hex. yH d1...dk Decimal yH d1...dk m = 0, m = 48 0 ≤ xL ≤ 54(for 2 inch) [Range] 0 ≤ xL ≤ 72(for 3 inch) PA-6225 SERIES USER MANUAL Page 112...
Page 120  yL and yH specify the vertical direction data count for one bit image (yL + yH x 256) in bytes. [Description] GS w n [Name] Set bar code width. ASCII [Format] Hex. Decimal 1 ≤ n ≤ 6 [Range] Initial Value n = 2 PA-6225 SERIES USER MANUAL Page 113...
Page 121 01 model e v mode nl nh [data] Decimal 01 model e v mode nl nh [data] model=01, 02 e=4Ch, 4Dh, 51h, 48h 0, 1 ≤ v ≤ 40 [Range] mode=4Eh, 41h, 42h, 4Bh, 4Dh 1≤ nh×256+nl≤ 7089 PA-6225 SERIES USER MANUAL Page 114...
Page 122 Decimal 0 ≤ n ≤ 255 [Range] Initial Value n = 0 [Description] Batch specifies the Kanji character print mode. “0” “1” Function Underline Undefined Undefined Undefined Double tall expanded Expanded wide Undefined Undefined PA-6225 SERIES USER MANUAL Page 115...
Page 123 Kanji character underlines. 2,50 Sets to two-dot width Kanji character underline and cancels Kanji character underlines. FS . [Name] Cancel Kanji character mode. ASCII [Format] Hex. Decimal [Range] [Description] Cancels Kanji character mode. PA-6225 SERIES USER MANUAL Page 116...
Page 124 Specifies or cancels quadruple size Kanji character.  Cancels quadruple size when n = <*******0>B. [Description]  Specifies quadruple size when n = <*******1>B.  n is effective only when it is the lowest bit. PA-6225 SERIES USER MANUAL Page 117...
Page 125 This setup also installs the MB1030 program. • Follow the wizard instructions to complete the installation. • Launching the Program The following steps guide you to load the MB1030 program. Click MB1030ra_SampleCode.exe to launch the program. • PA-6225 SERIES USER MANUAL Page 118...
Page 126 Chapter 3 Software OPOS Control Object of MB1030 Program a.) Print Normal buttons: Button/Item Description Printer Normal Print the string. PA-6225 SERIES USER MANUAL Page 119...
Page 127 Chapter 3 Software b.) Image buttons/items: Button/Item Description Set Bitmap Set bitmap file. Print Bitmap Print bitmap file. Print Memory Bitmap Print bitmap file from the memory PA-6225 SERIES USER MANUAL Page 120...
Page 128 Default Value Note BaudRate String 115200 UART Baud Rate (default) BitLength String UART Data Bit (default) Parity String UART Parity Bit (default) Port String COM4 UART Port (default) Stop String UART Stop Bit (default) PA-6225 SERIES USER MANUAL Page 121...
Page 129 Not Applicable Properties specific bool CapTransaction Read only Not Applicable Properties specific bool CapJrnPresent Read only Not Applicable Properties specific bool CapJrn2Color Read only Not Applicable Properties specific bool CapJrnBold Read only Not Applicable PA-6225 SERIES USER MANUAL Page 122...
Page 130 Not Applicable Properties specific bool CapSlpBitmap Read only Not Applicable Properties specific bool CapSlpBold Read only Not Applicable Properties specific bool CapSlpBothSidesPrint Read only Not Applicable Properties specific long CapSlpCartridgeSensor Read only Not Applicable PA-6225 SERIES USER MANUAL Page 123...
Page 131 Properties specific long JrnCartridgeState Read only Not Applicable Properties specific long JrnCurrentCartridge Not Applicable Properties specific long RecLineChars Not Applicable Properties specific string RecLineCharsList Read only Not Applicable Properties specific long RecLineHeight Not Applicable PA-6225 SERIES USER MANUAL Page 124...
Page 132 Claim Supported Methods common ClaimDevice Supported Methods common Release Supported Methods common ReleaseDevice Supported Methods common CheckHealth Supported Methods common ClearInput Not Applicable Methods common ClearOutput Not Applicable Methods common DirectIO Not Applicable PA-6225 SERIES USER MANUAL Page 125...
Page 133 Not Applicable Methods specific MarkFeed Not Applicable Events common DataEvent Not Applicable Events common DirectIOEvent Not Applicable Events common ErrorEvent Not Applicable Events common OutputComplete Not Applicable Event Events common StatusUpdate Not Applicable Event PA-6225 SERIES USER MANUAL Page 126...
Page 134: Vfd: Mb-4103 (Rs-232)
Parity Port COM1 Stop OPOS VFD Service Object and Method Relations Method Status of support Notes ○ Open ○ Close ○ ClaimDevice ○ ReleaseDevice ○ Enable ○ Disable ○ DisplayText ○ DisplayTextAt ○ ClearText PA-6225 SERIES USER MANUAL Page 127...
Page 135 Follow the wizard instructions to complete the installation. • Launching the Program The following steps guide you to load the Prox-PMP4000 program. Click LineDisplay folder from the path C/Program Files(x86)/Protech OPOS/POS • VFD/MB4000 Click Prox-PMP4000 to launch the program. •...
Page 136 Blink: Enable the display screen to blink. • Reverse: Enable the character printing in reverse black • and white. Blink+Reverse: Enable the display screen to blink and • activate the character printing in reverse black and white. PA-6225 SERIES USER MANUAL Page 129...
Page 137 Description Properties common long ControlObject Version Read only Not Applicable Properties common ServiceObject Read only Supported string Description Properties common long ServiceObject Version Read only Supported Properties common DeviceDescription Read only Supported string PA-6225 SERIES USER MANUAL Page 130...
Page 138 Properties specific long MarqueeRepeatWait Not Applicable Properties specific long InterCharacterWait Not Applicable Properties specific string CustomGlyphList Read only Not Applicable Properties specific long GlyphHeight Read only Not Applicable Properties specific long GlyphWidth Read only Not Applicable PA-6225 SERIES USER MANUAL Page 131...
Page 139 Not Applicable Methods specific DefineGlyph Not Applicable Events common DataEvent Not Applicable Events common DirectIOEvent Not Applicable Events common ErrorEvent Not Applicable Events common OutputComplete Not Applicable Event Events common StatusUpdate Not Applicable Event PA-6225 SERIES USER MANUAL Page 132...
Page 140: Msr: Mb-301X (Usb)
Follow the wizard instructions to complete the installation. • 2. Launching the Program The following steps guide you to load the MSR OPOS Driver program. Click MSR folder from the path Start/Programs/OPOS. • Click D04-301x-xxx-xx-xxxxxx to launch the program. • PA-6225 SERIES USER MANUAL Page 133...
Page 141 Chapter 3 Software 3. Configuration of D04-301x-xxx-xx-xxxxxx program a.) Main screen & Control tab items: PA-6225 SERIES USER MANUAL Page 134...
Page 142 Chapter 3 Software b.) General Setting PA-6225 SERIES USER MANUAL Page 135...
Page 143 Chapter 3 Software c.) Track Control tab items PA-6225 SERIES USER MANUAL Page 136...
Page 144 Chapter 3 Software d.) Track Data tab items PA-6225 SERIES USER MANUAL Page 137...
Page 145 Type Default Value Note default string PMP3000 OPOS S.O Link 5. OPOS APIs Support List OPOS Category Name Mutability VFD .SO Type Version Properties common bool AutoDisable Supported Properties common long BinaryConversion Not Applicable PA-6225 SERIES USER MANUAL Page 138...
Page 146 Properties specific string Track1Data Read only Supported Properties specific string Track2Data Read only Supported Properties specific string Track3Data Read only Supported Properties specific string Track4Data Read only Not Applicable Properties specific string AccountNumber Read only Supported PA-6225 SERIES USER MANUAL Page 139...
Page 147 Methods common ClearOutput Not Applicable Methods common DirectIO Not Applicable Events common DataEvent Supported Events common DirectIOEvent Not Applicable Events common ErrorEvent Not Applicable Events common OutputCompleteEvent Not Applicable Events common StatusUpdateEvent Not Applicable PA-6225 SERIES USER MANUAL Page 140...
Page 148: Msr: Giga-Tms Mjr243 (Rs-232)
Device Name for CO open FileName (NULL) (reserved) HardwareProvider (reserved) Model MJR243 Device model name Parity None Parity for the communication port Port COM4 COM Port Protocol Hardware Communication Control Baudrate 19200 RS232 baudrate PA-6225 SERIES USER MANUAL Page 141...
Page 149 Read only ○ DeviceName Read only ○ CapISO Read only ○ CapTransmitSentinels Read only ○ AccountNumber Read only ○ DecodeData ○ ExpirationDate Read only ○ FirstName Read only ○ MiddleInitial Read Only ○ ParseDecodeData PA-6225 SERIES USER MANUAL Page 142...
Page 150 Read Only ○ Surname Read Only ○ Title Read Only ○ Track1Data Read Only ○ Track1DiscretionaryData Read Only ○ Track2Data Read Only ○ Track2DiscretionaryData Read Only ○ Track3Data Read Only ○ TracksToRead ○ TransmitSentinels PA-6225 SERIES USER MANUAL Page 143...
Page 151: Api
XML file for each model Version.ini Version information Sample Program Directory Contents / File Name Description DEMO DEMO PROJECT\GPIO Sample C# VB6 VB.net Source Code PROJECT\ Code DEMO PROJECT\Digital C# VB6 VB.net Source Code Sample Code PA-6225 SERIES USER MANUAL Page 144...
Page 152: Api Procedure
Dim Receive_Status1 as Boolean Dim Receive_Status2 as Boolean Receive_Status1 = CashDrawerOpen(&H1) If Receive_Status1 = true then Text1.text = “cash drawer1 open” ‘enter text into textbox. Else Text1.text = “cash drawer1 close” ‘enter text into textbox. PA-6225 SERIES USER MANUAL Page 145...
Page 153 End if ‘========================================= Receive_Status2 = CashDrawerOpen(&H2) If Receive_Status2 = true then Text2.text = “cash drawer2 open” ‘enter text into textbox. Else Text2.text = “cash drawer2 close” ‘enter text into textbox. End if ‘========================================= End sub PA-6225 SERIES USER MANUAL Page 146...
Page 154: Sample Code
 Call Function Open cash drawer: CashDrawerOpen(1) Open cash drawer1 CashDrawerOpen(2) Open cash drawer2 Check cash drawer status: Dim receive_status as Boolean Check cash drawer1 status Receive_Status = CashDrawerOpen(&H1) Check cash drawer2 status Receive_Status = CashDrawerOpen(&H2) PA-6225 SERIES USER MANUAL Page 147...
Page 155 Open cash drawer1 PortAccess.CashDrawerOpen(0x01); //check cash drawer1 status Open cash drawer2 PortAccess.CashDrawerOpen(0x02); //check cash drawer2 status Bool bstatus; bstatus = PortAccess.GetCashDrawerStatus(0x01); bstatus = PortAccess.GetCashDrawerStatus(0x02); //Before get cash drawer status, need to initial cash drawer first PA-6225 SERIES USER MANUAL Page 148...
Page 156 As Boolean VB 6 extern function: Declare Function CashDrawerOpen Lib "CashDrawer.dll" (ByVal num_drawer As Integer) As Boolean Declare Function GetCashDrawerStatus Lib "CashDrawer.dll" (ByVal num_drawer As Integer) As Boolean Note: VB.net short = integer VB6 PA-6225 SERIES USER MANUAL Page 149...
Page 157: Cash Drawer
Description OPEN (button) Tap to open the cash drawer. Cash Drawer Status Cash drawer status will be displayed after OPEN is tapped.  Drawer is closed as shown:  Drawer is open as shown: PA-6225 SERIES USER MANUAL Page 150...
Page 158: Api Function
The API program-related sample programs, developed in VB.Net and C#, are provided for easy use of the API Package. Refer to the main API functions listed as below: API Function Cash Drawer CashDrawerOpen multilangXML.dll CashDrawer.dll GetCashDrawerStatus PA-6225 SERIES USER MANUAL Page 151...
Page 159: Cash Drawer Function
True (1) on success, False (0) on failure Example: Short data; data= GetCashDrawerStatus(0x01); // Get the Cash Drawer1 status if (data) MsgBox(“open1”); // Cash Drawer1 status “Open” Else MsgBox(“close1”); // Cash Drawer1 status “Close” Endif PA-6225 SERIES USER MANUAL Page 152...
Page 160: Bios Operation
3-4. BIOS Operation 3-4-1. Introduction The PA-6225 board uses an AMI Aptio BIOS that is stored in the Serial Peripheral Interface Flash Memory (SPI Flash) and can be updated. The SPI Flash contains the BIOS Setup program, Power-On Self-Test (POST), the PCI auto-configuration utility, LAN EEPROM information, and Plug and Play support.
Page 161 The BIOS Setup program is accessed by pressing the <Del> or <ESC> key after the POST memory test begins and before the operating system boot begins. All the menu settings are described in details in this chapter. PA-6225 SERIES USER MANUAL Page 154...
Page 162: Accessing Setup Utility
Enter to confirm and enter the sub-menu. A brief help message of the selected item will also appear at the bottom of the screen for your information. The following table provides the list of the keys that you can use while operating the BIOS setup menu. PA-6225 SERIES USER MANUAL Page 155...
Page 163 The CMOS battery is The battery may be losing power and users should bad or has been recently replace the battery immediately. Also, this message is replaced. displayed once the new battery is replaced. PA-6225 SERIES USER MANUAL Page 156...
Page 164 Chapter 3 Software BIOS Setup Program Initialization Screen PA-6225 SERIES USER MANUAL Page 157...
Page 165: Main
Displays the current UEFI version. Project No changeable options Displays the version of the BIOS Version currently installed on the platform. Build Date and No changeable options Displays the date of current BIOS Time version. PA-6225 SERIES USER MANUAL Page 158...
Page 166 “Day” is automatically changed. System Time hour, minute, second Sets the system time. The format is [Hour: Minute: Second]. Users can directly enter values or use <+> or <-> arrow keys to increase/decrease it. PA-6225 SERIES USER MANUAL Page 159...
Page 167: Advanced
Hardware Monitor Sub-Menu Monitors hardware status. F81866 Watchdog Sub-Menu F81866 Watchdog Parameters. CPU Configuration Sub-Menu CPU Configuration Parameters. IDE Configuration Sub-Menu SATA Configuration Parameters. OS Selection Sub-Menu OS Selection Voltage/RI Adjust Sub-Menu Voltage Adjustment settings. PA-6225 SERIES USER MANUAL Page 160...
Page 168 Power Management Interface) settings, such as Enable/Disable the functions of ACPI Auto Configuration, Hibernation and lock legacy resources. ACPI Settings Screen BIOS Setting Options Description/Purpose Enable ACPI - Disabled Enables or Disables ACPI feature. Auto - Enabled Configuration PA-6225 SERIES USER MANUAL Page 161...
Page 169 Enables or disables the locking of the Resources legacy resources. - Enabled 3-4-4-2. Hardware Monitor Hardware Monitor Screen BIOS Setting Options Description/Purpose No changeable options Displays the processor's temperature. Temperature System No changeable options Displays the system's temperature. Temperature PA-6225 SERIES USER MANUAL Page 162...
Page 170 Displays the voltage level of VCC3V VCC3V No changeable options in supply. Displays the voltage level of VSB3V in VSB3V No changeable options supply. Displays the voltage level of VBAT in VBAT No changeable options supply. PA-6225 SERIES USER MANUAL Page 163...
Page 171 Enables/ Disables Watch dog timer. WatchDog -Disable Watchdog Select seconds or minutes timer unit -60s Count for Multiple options Sets the desired value (seconds) for the Timer ranging from 1 to 255 watchdog timer. (Seconds) PA-6225 SERIES USER MANUAL Page 164...
Page 172 - Disabled Enables for legacy operating systems to Maximum boot processors with extended CPUID - Enabled functions. When this option is enabled, the processor will limit the maximum CPUID input value to 03h when PA-6225 SERIES USER MANUAL Page 165...
Page 173 Set “Disabled” for WinXP. Intel - Disabled When enabled, a VMM (Virtual Virtualization Machine Monitor) can utilize the - Enabled Technology additional hardware capabilities provided by Vanderpool Technology (VT). PA-6225 SERIES USER MANUAL Page 166...
Page 174 No changeable options Reports if Intel Hyper-Threading Technology Technology is supported by the processor. Hyper Threading is Intel’s term for its simultaneous multithreading implementation in their CPUs. Enable this function will improve parallelization of computation PA-6225 SERIES USER MANUAL Page 167...
Page 175 L1 Code Cache No changeable options Displays the size of L1 Code Cache. L2 Cache No changeable options Displays the size of L2 Cache. L3 Cache No changeable options Displays the size of L3 Cache. PA-6225 SERIES USER MANUAL Page 168...
Page 176 • Gen2 mode sets the device to 3 Gbit/s speed (in case it is compatible). SATA Mode - IDE mode Configures SATA as following: • IDE: Set SATA operation mode to IDE - AHCI mode mode. PA-6225 SERIES USER MANUAL Page 169...
Page 177 0. Shows [Empty] if no drive is installed. If the mother board supports RAID, it will show ASMT109x- Conf (0.1GB) Note*1: If the board support RAID function, the switch controls RAID SATA Port (SATA1 and SATA2) on board. PA-6225 SERIES USER MANUAL Page 170...
Page 178 Chapter 3 Software 3-4-4-6. OS Selection OS Selection Screen BIOS Setting Options Description/Purpose OS Selection - Windows 8.x & 10 Operating System Selection - Windows 7 PA-6225 SERIES USER MANUAL Page 171...
Page 179 Voltage Adjustment Configuration Screen BIOS Setting Options Description/Purpose COM1 Select - Disabled Selects COM1 Port voltage. -12V COM2 Select - Disabled Selects COM2 Port voltage. -12V COM3 Select - Disabled Selects COM3 Port voltage. -12V PA-6225 SERIES USER MANUAL Page 172...
Page 180 Chapter 3 Software BIOS Setting Options Description/Purpose COM4 Select - Disabled Selects COM4 Port voltage. -12V Cash drawer - Cash drawer 12V Selects Cash drawer voltage. - Cash drawer 24V PA-6225 SERIES USER MANUAL Page 173...
Page 181 Displays the current CSM version. Module Version GateA20 - Upon Request Selects Gate A20 operation mode. Active  Upon Request: GA20 can be - Always disabled using BIOS services.  Always: Do not allow disabling PA-6225 SERIES USER MANUAL Page 174...
Page 182 Controls the execution of UEFI and - UEFI only Legacy Video. - Legacy only Other PCI - UEFI only Select launch method for other PCI devices - Legacy only devices, such as NIC, mass storage or video card. PA-6225 SERIES USER MANUAL Page 175...
Page 183 This is a workaround for OSes without XHCI (Extensible Host Controller - Enabled Interface) hand-off support. EHCI Hand-off - Disabled This is a workaround for OSes without EHCI (Enhanced Host Controller - Enabled Interface) hand-off support. PA-6225 SERIES USER MANUAL Page 176...
Page 184 1 to 40 seconds in one second increment. seconds Mass Storage - Auto Displays the device name and chooses Devices: the mass storage emulation type. - Floppy - Force FDD - Hard Disk - CD-ROM PA-6225 SERIES USER MANUAL Page 177...
Page 185 Serial Port 2 Sub-menu Set Parameters for COM2 Configuration Serial Port 3 Sub-menu Set Parameters for COM3 Configuration Serial Port 4 Sub-menu Set Parameters for COM4 Configuration Parallel Port Sub-menu Set Parameters for LPT port. Configuration PA-6225 SERIES USER MANUAL Page 178...
Page 186 1. Change - Use Automatic Settings Select IRQ and I/O Settings - IO=3F8h; IRQ=4; resource settings for - IO=3F8h; IRQ=3,4,5,6,7,9,10,11,12; serial port 1. - IO=2F8h; IRQ=3,4,5,6,7,9,10,11,12; - IO=3E8h; IRQ=3,4,5,6,7,9,10,11,12; - IO=2E8h; IRQ=3,4,5,6,7,9,10,11,12; PA-6225 SERIES USER MANUAL Page 179...
Page 187 2. Change - Use Automatic Settings Select IRQ and I/O Settings - IO=2F8h; IRQ=3; resource settings for - IO=3F8h; IRQ=3,4,5,6,7,9,10,11,12; serial port 2. - IO=2F8h; IRQ=3,4,5,6,7,9,10,11,12; - IO=3E8h; IRQ=3,4,5,6,7,9,10,11,12; - IO=2E8h; IRQ=3,4,5,6,7,9,10,11,12; PA-6225 SERIES USER MANUAL Page 180...
Page 188 3. Change - Use Automatic Settings Select IRQ and I/O Settings - IO=3E8h; IRQ=7; resource settings for - IO=3F8h; IRQ=3,4,5,6,7,9,10,11,12; serial port 3. - IO=2F8h; IRQ=3,4,5,6,7,9,10,11,12; - IO=3E8h; IRQ=3,4,5,6,7,9,10,11,12; - IO=2E8h; IRQ=3,4,5,6,7,9,10,11,12; PA-6225 SERIES USER MANUAL Page 181...
Page 189 No changeable options Settings settings of serial port 4. Change -Use Automatic Settings Select IRQ and I/O Settings -IO=2E8h; IRQ=10; resource settings for -IO=3F8h; IRQ=3,4,5,6,7,9,10,11,12; serial port 4. -IO=2F8h; IRQ=3,4,5,6,7,9,10,11,12; -IO=3E8h; IRQ=3,4,5,6,7,9,10,11,12; -IO=2E8h; IRQ=3,4,5,6,7,9,10,11,12; PA-6225 SERIES USER MANUAL Page 182...
Page 190 - SPP Mode parallel port. Not available - EPP-1.9 and SPP Mode if the parallel port is - EPP-1.7 and SPP Mode disabled. - ECP Mode - ECP and EPP 1.9 Mode SPP is Standard Parallel PA-6225 SERIES USER MANUAL Page 183...
Page 191 Port mode, a bi-directional mode for printers. EPP is Enhanced Parallel Port mode, a high-speed bi-directional mode for non-printer peripherals. ECP is Enhanced Capability Port mode, a high-speed bi-directional mode for printers and scanners. PA-6225 SERIES USER MANUAL Page 184...
Page 192: Chipset
Chapter 3 Software 3-4-5. Chipset Chipset Screen BIOS Setting Options Description/Purpose North Bridge Sub-menu Sets parameter for North Bridge configuration. South Bridge Sub-menu Sets parameters for South Bridge configuration. PA-6225 SERIES USER MANUAL Page 185...
Page 193 North Bridge Screen BIOS Setting Options Description/Purpose Intel IGD Sub-menu Configures Graphic Settings. Configuration Memory No changeable options Displays the DRAM information on Information the platform. Total Memory No changeable options Displays the DRAM size PA-6225 SERIES USER MANUAL Page 186...
Page 194 Adaptor. • Disabled: Always disables IGD. IGD Turbo - Disabled Enables or disables IGD Turbo Enable - Enabled DVMT Pre- - 32M Selects DVMT 5.0 Pre-Allocated Allocated (Fixed) Graphics Memory size used - 64M PA-6225 SERIES USER MANUAL Page 187...
Page 195 3-4-5-2. South Bridge South Bridge Screen BIOS Setting Options Description/Purpose Sub-menu Configures USB parameters. Configuration PCI Express Sub-menu Configures PCH PCIE parameters. Configuration High Precision - Disabled Enables or disables the HPET (High Precision PA-6225 SERIES USER MANUAL Page 188...
Page 196 AC power is removed. USB Configuration Screen BIOS Setting Options Description/Purpose USB 2.0 - Disabled (XHCI Mode must be disabled.) (EHCI) Enables Enhanced Host Controller - Enabled Support Interface 1 for high-speed USB PA-6225 SERIES USER MANUAL Page 189...
Page 197 Enables or Disables USB port 1. - Enabled USB Port 2 - Disabled Enables or Disables USB port 2. - Enabled USB Port 3 - Disabled Enables or Disables USB port 3. - Enabled PA-6225 SERIES USER MANUAL Page 190...
Page 198 - Gen1 - Gen2 PCI Express - Disabled Enables or Disables PCI Express port 3. Port 3(For - Enabled RTL8111) Speed - Auto Selects the speed of PCI Express port 3. - Gen1 - Gen2 PA-6225 SERIES USER MANUAL Page 191...
Page 199: Security
Chapter 3 Software 3-4-6. Security Security Screen BIOS Setting Options Description/Purpose Administrator Password can be 3-20 Specifies the administrator password. Password alphanumeric characters. User Password Password can be 3-20 Specifies the user password. alphanumeric characters. PA-6225 SERIES USER MANUAL Page 192...
Page 200: Boot
- Off • On: Enables the NumLock function automatically after the system is powered on. • Off: Disables the NumLock function after the system is powered Quiet Boot - Disabled Enables/Disables Quiet Boot option. PA-6225 SERIES USER MANUAL Page 193...
Page 201 Hard Drive Sub-Menu Defines the boot order for all the hard BBS Priorities drives connected to the system, e.g. SATA, USB drive. PA-6225 SERIES USER MANUAL Page 194...
Page 202 Enter to enter the sub-menu and press <↑> or <↓> arrow keys to select the device. Another way is to press <+> or <-> to move the selected device up/down in the priority list. PA-6225 SERIES USER MANUAL Page 195...
Page 203: Save & Exit
Chapter 3 Software 3-4-8. Save & Exit Save & Exit Screen PA-6225 SERIES USER MANUAL Page 196...
Page 204 Resets the system without saving any Changes and changes made in BIOS settings. Reset Restore No changeable options Loads the optimized defaults for BIOS Defaults settings. Boot Override - [Drive(s)] Forces to boot the system from the selected [drive(s)]. PA-6225 SERIES USER MANUAL Page 197...
Page 205: Watchdog Timer Configuration
To exit the Extended Function Mode, writing 0xAA to the EFER is required. Once the chip exits the Extended Function Mode, it is in the normal running mode and is ready to enter the configuration mode. PA-6225 SERIES USER MANUAL Page 198...
Page 206 ;------ Enter to extended function mode -------------------------------------------------------- ;------ Select Logical Device 7 of watchdog timer -------------------------------------------- ;------ Enable Watch dog feature -------------------------------------------- 030h ;------ Enable Watch PME-------------------------------------------- 0FAh ;------ Set second as counting unit -------------------------------------------------------------- 0f5h PA-6225 SERIES USER MANUAL Page 199...
Page 207 Chapter 3 Software ;------ Set timeout interval as 30seconds and start counting --------------------------------- 0f6h ;------ Exit the extended function mode -------------------------------------------------------- 0aah PA-6225 SERIES USER MANUAL Page 200...
Page 208: Bios Update Instructions
Select [Boot] menu as the picture shows below. Select [Hard Drive BBS Priorities], set the USB bootable device as the 1 boot device. Press <F4> key to save configuration and exit the BIOS setup menu. PA-6225 SERIES USER MANUAL Page 201...
Page 209 The recommended options for BIOS ROM update consist of following parameters: program main BIOS image /B: program Boot Block /N: program NVRAM /X: don’t check ROM ID PA-6225 SERIES USER MANUAL Page 202...
Page 210 Restart the system and boot up the system with new BIOS now. The BIOS Update procedure is completed after the system is restarted. Reboot the system and verify if the BIOS version shown on the initialization screen has been updated. PA-6225 SERIES USER MANUAL Page 203...
Page 211 Chapter 3 Software PA-6225 SERIES USER MANUAL Page 204...
Page 212: System Resource Map
81~511 Microsoft ACPI-Compliant System-Compliant System ® 4294967291 Intel HD Graphics ® 4294967292 Intel USB 3.0 eXtensible Host Controller - 0100 (Microsoft) ® 4294967293 Intel Trusted Execution Engine Interface 4294967294 Realtek PCIe GBE Family Controller PA-6225 SERIES USER MANUAL Page 205...
Page 213 Chapter 3 Software DMA Channels Map TIMER CHANNEL ASSIGNMENT Channel 4 Direct memory access controller PA-6225 SERIES USER MANUAL Page 206...
Page 214 PCI Express Root Complex 0x00000080-0x0000008F Motherboard resources 0x00000092-0x00000092 Motherboard resources 0x000000A0-0x000000A1 Programmable interrupt controller 0x000000A4-0x000000A5 Programmable interrupt controller 0x000000A8-0x000000A9 Programmable interrupt controller 0x000000AC-0x000000AD Programmable interrupt controller 0x000000B0-0x000000B1 Programmable interrupt controller 0x000000B2-0x000000B3 Motherboard resources 0x000000B4-0x000000B5 Programmable interrupt controller PA-6225 SERIES USER MANUAL Page 207...
Page 215 N- and J-series AHCI - 0F23 ® ® ® 0x0000F050-0x0000F057 Intel Pentium processor N- and J-series / Intel ® Celeron processor N- and J-series AHCI - 0F23 ® ® ® 0x0000F060-0x0000F063 Intel Pentium processor N- and J-series / Intel PA-6225 SERIES USER MANUAL Page 208...
Page 216 Celeron processor N- and J-series AHCI - 0F23 ® ® ® 0x0000F070-0x0000F077 Intel Pentium processor N- and J-series / Intel ® Celeron processor N- and J-series AHCI - 0F23 ® 0x0000F080-0x0000F087 Intel HD Graphics PA-6225 SERIES USER MANUAL Page 209...
Page 217 0xD0500000-0xD05FFFFF Intel Trusted Execution Engine Interface ® 0xD0400000-0xD04FFFFF Intel Trusted Execution Engine Interface ® ® ® 0xD0711000-0xD07117FF Intel Pentium processor N- and J-series / Intel ® Celeron processor N- and J-series AHCI - 0F23 PA-6225 SERIES USER MANUAL Page 210...
Page 218 High Definition Audio Controller IRQ 17 PCI standard PCI-to-PCI bridge IRQ 81 Microsoft ACPI-Compliant System IRQ 82 Microsoft ACPI-Compliant System IRQ 83 Microsoft ACPI-Compliant System IRQ 84 Microsoft ACPI-Compliant System IRQ 85 Microsoft ACPI-Compliant System PA-6225 SERIES USER MANUAL Page 211...
Page 219 IRQ 99 Microsoft ACPI-Compliant System IRQ 100 Microsoft ACPI-Compliant System IRQ 101 Microsoft ACPI-Compliant System IRQ 102 Microsoft ACPI-Compliant System IRQ 103 Microsoft ACPI-Compliant System IRQ 104 Microsoft ACPI-Compliant System IRQ 105 Microsoft ACPI-Compliant System PA-6225 SERIES USER MANUAL Page 212...
Page 220 IRQ 131 Microsoft ACPI-Compliant System IRQ 132 Microsoft ACPI-Compliant System IRQ 133 Microsoft ACPI-Compliant System IRQ 134 Microsoft ACPI-Compliant System IRQ 135 Microsoft ACPI-Compliant System IRQ 136 Microsoft ACPI-Compliant System IRQ 137 Microsoft ACPI-Compliant System PA-6225 SERIES USER MANUAL Page 213...
Page 221 IRQ 162 Microsoft ACPI-Compliant System IRQ 163 Microsoft ACPI-Compliant System IRQ 164 Microsoft ACPI-Compliant System IRQ 165 Microsoft ACPI-Compliant System IRQ 166 Microsoft ACPI-Compliant System IRQ 167 Microsoft ACPI-Compliant System IRQ 168 Microsoft ACPI-Compliant System PA-6225 SERIES USER MANUAL Page 214...
Page 222 Microsoft ACPI-Compliant System IRQ 11 SM Bus Controller IRQ 18 PCI standard PCI-to-PCI bridge DMA Channels Map TIMER CHANNEL ASSIGNMENT Channel 3 Printer Port (LPT1) I /O Map I/O MAP ASSIGNMENT 0x00000064-0x00000064 Standard PS/2 Keyboard PA-6225 SERIES USER MANUAL Page 215...
Page 223 Intel Celeron Processor J1900 ® ® 0x000003B0-0x000003BB Intel Celeron Processor J1900 ® ® 0x000003C0-0x000003DF Intel Celeron Processor J1900 0x00000378-0x0000037F Printer Port (LPT1) 0x000003F8-0x000003FF Communications Port (COM1) 0x000002F8-0x000002FF Communications Port (COM2) 0x000003E8-0x000003EF Communications Port (COM3) PA-6225 SERIES USER MANUAL Page 216...
Page 224 Motherboard resources 0x00000A20-0x00000A2F Motherboard resources 0x000000B2-0x000000B3 Motherboard resources 0x0000164E-0x0000164F Motherboard resources 0x00000070-0x00000077 Motherboard resources 0x0000002E-0x0000002F Motherboard resources 0x0000004E-0x0000004F Motherboard resources 0x00000063-0x00000063 Motherboard resources 0x00000065-0x00000065 Motherboard resources 0x00000067-0x00000067 Motherboard resources 0x00000080-0x0000008F Motherboard resources 0x00000092-0x00000092 Motherboard resources PA-6225 SERIES USER MANUAL Page 217...
Page 225 ® 0xA0000-0xBFFFF Intel Celeron Processor J1900 0xA0000-0xBFFFF PCI bus 0xD0604000-0xD0604FFF Ethernet Controller 0xD0600000-0xD0603FFF Ethernet Controller 0xD0600000-0xD0603FFF PCI standard PCI-to-PCI bridge 0xD0705000-0xD07053FF Standard Enhanced PCI to USB Host Controller 0xC0000-0xDFFFF PCI bus 0xE0000-0xFFFFF PCI bus PA-6225 SERIES USER MANUAL Page 218...
Page 226 Motherboard resources 0xFED0C000-0xFED0FFFF Motherboard resources 0xFED08000-0xFED08FFF Motherboard resources 0xFED1C000- Motherboard resources 0xFED1CFFF 0xFEE00000-0xFEEFFFFF Motherboard resources 0xFEF00000-0xFEFFFFFF Motherboard resources 0xD0700000-0xD0703FFF High Definition Audio Controller 0xD0704000-0xD070401F SM Bus Controller 0xD0500000-0xD05FFFFF PCI Encryption/Decryption Controller 0xD0400000-0xD04FFFFF PCI Encryption/Decryption Controller PA-6225 SERIES USER MANUAL Page 219...
Page 227: Chapter 4 System Diagrams
CHAPTER SYSTEM DIAGRAMS This appendix contains exploded diagrams and part numbers of the PA-6225 system. The following topics are included:  Exploded Diagrams for Panel PC  Cable Cover  Storage  Back Cover  Touchscreen  LCD Panel  Inside Case ...
Page 228: Exploded Diagrams For Panel Pc
Chapter 4 System Assembly EXPLODED DIAGRAM FOR PANEL PC 1. Cable Cover PA-6225 SERIES USER MANUAL Page 221...
Page 229 Chapter 4 System Assembly 2. Storage PA-6225 SERIES USER MANUAL Page 222...
Page 230 Chapter 4 System Assembly PA-6225 SERIES USER MANUAL Page 223...
Page 231 Chapter 4 System Assembly PA-6225 SERIES USER MANUAL Page 224...
Page 232 Chapter 4 System Assembly 3. Back Cover PA-6225 SERIES USER MANUAL Page 225...
Page 233 Chapter 4 System Assembly PA-6225 SERIES USER MANUAL Page 226...
Page 234 Chapter 4 System Assembly 4. Touchscreen Resistive PA-6225 SERIES USER MANUAL Page 227...
Page 235 Chapter 4 System Assembly Projected Capacitive PA-6225 SERIES USER MANUAL Page 228...
Page 236 Chapter 4 System Assembly 5. LCD Panel PA-6225 SERIES USER MANUAL Page 229...
Page 237 Chapter 4 System Assembly 6. Inside Case Fundamental PA-6225 SERIES USER MANUAL Page 230...
Page 238 Chapter 4 System Assembly PA-6225 SERIES USER MANUAL Page 231...
Page 239 Chapter 4 System Assembly For Resistive Touchscreen PA-6225 SERIES USER MANUAL Page 232...
Page 240 Chapter 4 System Assembly For Projected Capacitive Touchscreen PA-6225 SERIES USER MANUAL Page 233...
Page 241: Exploded Diagrams For Stand
Chapter 4 System Assembly EXPLODED DIAGRAM FOR STAND 1. Small Stand PA-6225 SERIES USER MANUAL Page 234...
Page 242 Chapter 4 System Assembly Rotation Part PA-6225 SERIES USER MANUAL Page 235...
Page 243 Chapter 4 System Assembly Bottom Case PA-6225 SERIES USER MANUAL Page 236...
Page 244 Chapter 4 System Assembly PA-6225 SERIES USER MANUAL Page 237...
Page 245 Chapter 4 System Assembly 2. Multi-functional Stand – without printer PA-6225 SERIES USER MANUAL Page 238...
Page 246 Chapter 4 System Assembly Rotation Part Item Part Name Part No. Rotate base assembly xx-xxx-xxxxxxx HINGE-FIXING 80-012-03001314 SCREW/M5x0.8Px15m m 22-232-50015011 Stand Rotate Cover 30-002-28410314 SCREW/M3x0.5Px12m m 22-275-30010011 PA-6225 SERIES USER MANUAL Page 239...
Page 247 Chapter 4 System Assembly PA-6225 SERIES USER MANUAL Page 240...
Page 248 Storage Item Part Name Part No. Note No Printer Cover 30-002-28210314 RUBBER WASHER 23-680-3958096 3 option SCREW/M3x0.5Px4.8m m 82-272-3000501 3 option 2.5" HDD xx-xxx-xxxxxxxx option ESATA Cable 27-008-3140608 1 option SCREW/T2.6x5mm 22-732-2600581 1 option PA-6225 SERIES USER MANUAL Page 241...
Page 249 Chapter 4 System Assembly Bottom Case PA-6225 SERIES USER MANUAL Page 242...
Page 250 RUBBER FOOT(40x12x4mm ) 30-004-01100314 HEX CU BOSS/M3x0.5Px6L,H=15 22-290-30015051 Power cord xx-xxx-xxxxxxxx 72W Adaptor xx-xxx-xxxxxxxx 72W_ADAPTOR_BRACKE T 80-006-03001314 SCREW/M3x0.5Px5mm 22-242-30005311 120W Adaptor xx-xxx-xxxxxxxx Option 120W_ADAPTOR_BRACKE T 80-029-0300331 4 Option No Printer cover assembl y xx-xxx-xxxxxxxx SCREW/M3x0.5Px6mm 82-275-30006018 PA-6225 SERIES USER MANUAL Page 243...
Page 251 Chapter 4 System Assembly PA-6225 SERIES USER MANUAL Page 244...
Page 252 Printer EMI SHIELDING GASKE T 90-050-3110000 0 for with Printer RJ11 HOLDER 80-029-0300216 5 for with Printer Cash Drawer cable 27-026-1650511 1 for with Printer SCREW/M2.5x0.45Px4m m 22-232-2500401 1 for with Printer PA-6225 SERIES USER MANUAL Page 245...
Page 253 Chapter 4 System Assembly Item Part Name Part No. Stand Cover 30-002-28110314 CABLE CLAMP 90-023-04200314 SCREW/T3.0x8mm 22-122-30080011 PA-6225 SERIES USER MANUAL Page 246...
Page 254 Chapter 4 System Assembly 3. Multi-functional stand – with printer PA-6225 SERIES USER MANUAL Page 247...
Page 255 Chapter 4 System Assembly Extension Power Cable Item Part Name Part No. HEX CU BOSS/M3x0.5Px6L,H=15mm 22-290-30015051 DC IN CLIP 80-014-03001314 DC IN EXTENDED CABLE 27-012-31408111 SCREW/M3x0.5Px5mm 22-242-30005311 PA-6225 SERIES USER MANUAL Page 248...
Page 256 Chapter 4 System Assembly With RAID 2 Storage PA-6225 SERIES USER MANUAL Page 249...
Page 257 Chapter 4 System Assembly Item Part Name Part No. 2.5" HDD xx-xxx-xxxxxxxx HDD HOLDER 80-029-03002314 SCREW/M3x0.5Px4mm 22-215-3000431 1 STAND HDD COVER 30-002-02110314 SCREW/M3x0.5Px4mm 22-272-3000431 8 PA-6225 SERIES USER MANUAL Page 250...
Page 258 Chapter 4 System Assembly PA-6225 SERIES USER MANUAL Page 251...
Page 259 Chapter 4 System Assembly Item Part Name Part No. HDD SOCKET BRACKET 80-006-03004314 ESATA Cable 27-008-31406081 SCREW/M3x0.5Px5mm 22-230-30005811 PA-6225 SERIES USER MANUAL Page 252...
Page 260 Chapter 4 System Assembly Without RAID 2 Storage Front view Rear view Bottom view Item Part Name Part No. Printer Module xx-xxx-xxxxxxxx STAND HDD COVER 30-002-02110314 SCREW/T3.0x8mm 22-122-3008001 1 PA-6225 SERIES USER MANUAL Page 253...
Page 261 Chapter 4 System Assembly Thermal Printer PA-6225 SERIES USER MANUAL Page 254...
Page 262 Chapter 4 System Assembly Item Part Name Part No. Note STAND BRACKET ASSEMBL Y xx-xxx-xxxxxxxx RUBBER FOOT 30-004-01100314 STAND DRESS COVER 30-002-28510314 For with Printer STAND COVER ASSEMBL Y xx-xxx-xxxxxxx SCREW/T3.0x8mm 22-122-3008001 1 PA-6225 SERIES USER MANUAL Page 255...
Page 263 Chapter 4 System Assembly Top View Bottom View Separation View PA-6225 SERIES USER MANUAL Page 256...
Page 264 Chapter 4 System Assembly PA-6225 SERIES USER MANUAL Page 257...
Page 265 Chapter 4 System Assembly 3 Inch Printer PA-6225 SERIES USER MANUAL Page 258...
Page 266 Chapter 4 System Assembly 3 Inch Printer Assembly PA-6225 SERIES USER MANUAL Page 259...
Page 267 Printer Holder 80-029-03004314 Printer Board 17-122-10301028 Printer Board 52-370-06310008 Printer Board 17-160-10011023 SCREW/M2x0.4Px4mm 22-272-20004011 PRINTER-PCB-MYLAR 90-056-02100314 SCREW/M3x0.5Px5mm 22-242-30005311 3" Printer (Main body) 52-701-03017003 Front Cover Assembly xx-xxx-xxxxxxxx PAPER COVER PIN 20-004-10011165 ROTRAY DAMPER(15gf-cm) 90-022-09100314 PA-6225 SERIES USER MANUAL Page 260...
Page 268 Chapter 4 System Assembly Item Part Name Part No. STAND PRINTER COVER_ F 30-002-02210314 3" Printer (Main body) 52-701-03017003 SCREW/T3.0x5mm 22-121-3000501 1 PA-6225 SERIES USER MANUAL Page 261...
Page 269 Chapter 4 System Assembly 2 Inch Printer PA-6225 SERIES USER MANUAL Page 262...
Page 270 Chapter 4 System Assembly 2 Inch Printer Assembly PA-6225 SERIES USER MANUAL Page 263...
Page 271 17-122-10301028 Printer Board 52-370-06310008 Printer Board 17-160-10011023 SCREW/M2x0.4Px4mm 22-272-20004011 PRINTER-PCB-MYLAR 90-056-02100314 SCREW/M3x0.5Px5mm 22-242-30005311 2" Printer (Main body) 52-701-01020003 Front Cover Assembly xx-xxx-xxxxxxxx PAPER COVER PIN 20-004-10011165 ROTRAY DAMPER(15gf-cm) 90-022-09100314 2 inch PAPER BLOCK 30-061-28110242 PA-6225 SERIES USER MANUAL Page 264...
Page 272 Chapter 4 System Assembly Item Part Name Part No. STAND PRINTER COVER_ F 30-002-02210314 2" Printer (Main body) 52-701-01020003 SCREW/T3.0x5mm 22-121-3000501 1 PA-6225 SERIES USER MANUAL Page 265...
Page 273: Exploded Diagrams For Peripheral Devices
Chapter 4 System Assembly EXPLODED DIAGRAM FOR PERIPHERAL DEVICES 1. MSR & i-Button PA-6225 SERIES USER MANUAL Page 266...
Page 274 Chapter 4 System Assembly 2. Fingerprint PA-6225 SERIES USER MANUAL Page 267...
Page 275 Chapter 4 System Assembly 3. Adaptor Holder for Panel PC PA-6225 SERIES USER MANUAL Page 268...
Page 276 Chapter 4 System Assembly 4. VFD Kit Normal Type PA-6225 SERIES USER MANUAL Page 269...
Page 277 Chapter 4 System Assembly Rotated Type PA-6225 SERIES USER MANUAL Page 270...
Page 278 Chapter 4 System Assembly 5. Second Display PA-6225 SERIES USER MANUAL Page 271...
Page 279: Exploded Diagrams For Packing
Chapter 4 System Assembly EXPLODED DIAGRAM FOR PACKING PPC Packing PA-6225 SERIES USER MANUAL Page 272...
Page 280 Chapter 4 System Assembly POS Packing PA-6225 SERIES USER MANUAL Page 273...
Page 281 Chapter 4 System Assembly PPC Packing POS Packing PA-6225 SERIES USER MANUAL Page 274...
Page 282 Chapter 4 System Assembly PA-6225 SERIES USER MANUAL Page 275...
Page 283 Chapter 4 System Assembly PA-6225 SERIES USER MANUAL Page 276...

protech PA-6225 User Manual

Chapter 1 Introduction

Chapter 2 System Configuration

Chapter 3 Software Utilities

Chapter 4 System Diagrams

Quick Links

Need help?

Questions and answers

Related Manuals for protech PA-6225

Summary of Contents for protech PA-6225

Table of Contents