Table of Contents
Advertisement
Chapter 2
Chapter 2
2.2 Install the Inverter
2.2 Install the Inverter
2.2 Install the Inverter
2.2 Install the Inverter
Transportation
ransportation
The inverter
The inverter is made of plastics
is made of plastics component
•
carrying the inverter, handle it carefully to prevent
carrying the inverter, handle it carefully to prevent
carrying the inverter, handle it carefully to prevent
carrying the inverter, handle it carefully to prevent
carrying the inverter, handle it carefully to prevent
damage to the parts.
damage to the parts.
damage to the parts.
Do not carry the inverter by holding the front or
Do not carry the inverter by holding the front or
Do not carry the inverter by holding the front or
Do not carry the inverter by holding the front or
Do not carry the inverter by holding the front or
•
terminal block cover. Doing so may
terminal block cover. Doing so may cause the
terminal block cover. Doing so may
terminal block cover. Doing so may
inverter to fall.
inverter to fall.
Do not install and operate the inverter if it is
Do not install and operate the inverter if it is
Do not install and operate the inverter if it is
Do not install and operate the inverter if it is
Do not install and operate the inverter if it is
•
damaged or its parts are missing.
damaged or its parts are missing.
damaged or its parts are missing.
Ambient temperature
mbient temperature
mbient temperature
Avoid installing the inverter in a place where the
Avoid installing the inverter in a place where the
Avoid installing the inverter in a place where the
Avoid installing the inverter in a place where the
Avoid installing the inverter in a place where the
•
ambient temperature goes above or below the
ambient temperature goes above or below the
ambient temperature goes above or below the
ambient temperature goes above or below the
ambient temperature goes above or below the
allowable range defined by
allowable range defined by
allowable range defined by the standard inverter
specification.
specification.
Ambient temperature:
Ambient temperature:
Ambient temperature:
ND rated
ND rated
: -10 to 50°C
LD rated
LD rated
: -10 to 45°C
VLD rated
VLD rated
: -10 to 40°C
Keep
sufficient space around the inverter.
ent space around the inverter.
ent space around the inverter.
ent space around the inverter.
•
Measure the temperature in a position about 5 cm
Measure the temperature in a position about 5 cm
Measure the temperature in a position about 5 cm
Measure the temperature in a position about 5 cm
Measure the temperature in a position about 5 cm
distant from the bottom
distant from the bottom-center poi
distant from the bottom
inverter,
inverter,
inverter,
inverter,
inverter,
and
and
and
and
and
check
check
check
check
check
temperature
temperature is within the allowable range.
is within the allowable range.
is within the allowable range.
is within the allowable range.
Operating the inverter at a temperature outside
Operating the inverter at a temperature outside
Operating the inverter at a temperature outside
Operating the inverter at a temperature outside
Operating the inverter at a temperature outside
this range will shorten the inverter life (especially
this range will shorten the inverter life (especially
this range will shorten the inverter life (especially
this range will shorten the inverter life (especially
this range will shorten the inverter life (especially
the capacitor life), resulting in damage to the
the capacitor life), resulting in damage to the
the capacitor life), resulting in damage to the
the capacitor life), resulting in damage to the
the capacitor life), resulting in damage to the
inverter.
inverter.
Do not install on
Do not install
humidity
umidity or easily condensa
or easily condensation area
or easily condensa
Avoid installing the inverter in a place where the
Avoid installing the inverter in a place where the
Avoid installing the inverter in a place where the
Avoid installing the inverter in a place where the
Avoid installing the inverter in a place where the
•
relative humidity goes above or below the range
relative humidity goes above or below the range
relative humidity goes above or below the range
relative humidity goes above or below the range
relative humidity goes above or below the range
(20% to 90% RH), as defined by the standard
(20% to 90% RH), as defined by the standard
(20% to 90% RH), as defined by the standard
(20% to 90% RH), as defined by the standard
(20% to 90% RH), as defined by the standard
inverter specification. Avoid a place where the
inverter specification. Avoid a p
inverter specification. Avoid a p
inverter specification. Avoid a p
inverter is subject to condensation.
inverter is subject to condensation.
inverter is subject to condensation.
inverter is subject to condensation.
Condensation inside the inverter will result in
Condensation inside the inverter will result in
Condensation inside the inverter will result in
Condensation inside the inverter will result in
Condensation inside the inverter will result in
•
short circuits, which may c
short circuits, which may c
short circuits, which may cause
inverter.
inverter. Also avoid places where the inverter is
Also avoid places where the inverter is
Also avoid places where the inverter is
Also avoid places where the inverter is
exposed to direct sunlight.
exposed to direct sunlight.
exposed to direct sunlight.
component. When
. When
cause the
the standard inverter
the standard inverter
10 to 50°C
10 to 45°C
10 to 40°C
center point of the
nt of the
that
that
that
that
that
the
the
the
the
the
measured
measured
measured
measured
measured
a high temperature, high
a high temperature, high
a high temperature, high
area
lace where the
ause damage to the
to the
Install inverter on
nstall inverter on nonflammable
(e.g. metal) surface.
metal) surface.
metal) surface.
The inverter will reach a high temperature (up to
The inverter will reach a high temperature (up to
The inverter will reach a high temperature (up to
The inverter will reach a high temperature (up to
The inverter will reach a high temperature (up to
•
about 150°C) during operation. Install the inverter
about 150°C) during operation. Install the inverter
about 150°C) during operation. Install the inverter
about 150°C) during operation. Install the inverter
about 150°C) during operation. Install the inverter
on a vertical wall surface made of nonflammable
on a vertical wall surface made of nonflammable
on a vertical wall surface made of nonflammable
on a vertical wall surface made of nonflammable
on a vertical wall surface made of nonflammable
material (e.g., metal) to avoid the risk of fire.
material (e.g., metal) to avoid the risk of fire.
material (e.g., metal) to avoid the risk of fire.
material (e.g., metal) to avoid the risk of fire.
In particular, keep sufficient distance between the
In particular, keep
•
inverter and other heat sources (e.g., braking
inverter and other heat sources (e.g., braking
inverter and other heat sources (e.g., braking
inverter and other heat sources (e.g., braking
inverter and other heat sources (e.g., braking
resistors and reactors) if they are installed in the
resistors and reactors) if they are installed in the
resistors and reactors) if they are installed in the
resistors and reactors) if they are installed in the
resistors and reactors) if they are installed in the
vicinity.
For
For
P1-00044
00044-L to P1-02950
02950-L
(P1-
-004L to P1-550L)
550L)
or
P1-00041
00041-H to P1-01800
01800-H
(P1-
-007H to P1-550H)
550H)
10 cm
or more
or more
5 cm
5 cm
or more
or more
or more
10 cm
or more
or more
In order to replace life cycle parts on following models require
order to replace life cycle parts on following models require
order to replace life cycle parts on following models require
order to replace life cycle parts on following models require
order to replace life cycle parts on following models require
a clearance of 22cm or more:
a clearance of 22cm or more:
a clearance of 22cm or more:
• P1-00800-L (P1
L (P1-150L) to P1-
• P1-00380-H (P1
H (P1-150H) to P1
150H) to P1-00620-H (P1-220H)
In order to replace life cycle parts on following models is
In order to replace life cycle parts on following models is
In order to replace life cycle parts on following models is
In order to replace life cycle parts on following models is
required to remove the installed units:
remove the installed units:
remove the installed units:
• P1-00044-L (P1
L (P1-004L) to P1-
• P1-00041-H (P1
H (P1-007H) to P1
007H) to P1-00310-H (P1-110H)
Wall
Wall
Air flow
Air flow
2-2
Installation and Wiring
Installation and Wiring
Installation and Wiring
Installation and Wiring
nonflammable
nonflammable
sufficient distance between the
sufficient distance between the
sufficient distance between the
For
For
P1
P1-02160-H to P1
H to P1-03610-H
(P1
(P1-750H to P1-1320H)
1320H)
30 cm
30 cm
or more
or more
5 cm
5 cm
or more
or more
or more
30 cm
30 cm
or more
or more
-01240-L (P1-220L)
220L)
220H)
-00600-L (P1-110L)
110L)
110H)
Keep
Keep
Keep
Keep
enough
enough
enough
enough
clearance
clearance
clearance
clearance
•
between the inverter and the
between the inverter and the
between the inverter and the
between the inverter and the
above and below
above and below
above and below wiring ducts
wiring ducts
to
to
prevent
prevent
cooling
cooling
ventilation from
ventilation from obstructing.
ventilation from
obstructing.
For dimension drawing of
For dimension drawing of
For dimension drawing of
For dimension drawing of
inverter
inverter see chapter
chapter 2-5.
air
air
Advertisement
Table of Contents
