Washer Operation; Power Up; Ready Mode; Partial Vend Mode - ALLIANCE BF3JGBJG403UN01 Original Instructions Manual

Power Up

When power is applied to the washer, the control will display its
control type as FL, software version as SXXX (XX is the version
number) for one (1) second each. If the control was not powered
down during a running cycle, it will enter the Ready Mode.

Ready Mode

In this mode of operation, the display shows the current selected
cycle, modifier, temperature and the full current vend price for
that cycle. The INSERT COINS/CARD LED is lit.
To start the cycle, the user must satisfy the vend price and then
press the START keypad.
The user will be able to select a different cycle/wash water tem-
perature or modifier by pressing a cycle pad when the machine is
in the ready mode or before the first fill is complete.

Partial Vend Mode

The control enters this mode when part of the vend price has been
entered, but not enough vend is entered to satisfy the vend price.
The control will display the remaining vend price needed to start
the cycle and the INSERT COINS/CARD LED is lit.

Additional Vend Mode

The control enters this mode if a change is made before the first
fill is complete. If the vend price is not satisfied within one (1)
minute, the washer control will go back to the first selection and
the cycle will continue. Pressing the START keypad will cancel
cycle changes and exit this mode. After the first fill, all key
presses will be ignored, allowing the washer to go through the
complete cycle.

Start Mode

The control enters this mode when the full vend price is satisfied,
the vend price is zero, or the control is in OPL Mode. The
START pad LED will flash one (1) second on and one (1) second
off. If Start Mode is entered because the vend price is satisfied or
the control is in OPL Mode, the display will show PUSH for one
(1) second, StArt for one (1) second and the current cycle time
for one (1) second. If Start Mode is entered because the vend
price is zero (0), the display will show FrEE. When first entering
Start Mode, a signal will sound for one (1) second on and one (1)
second off for 10 seconds if Signal for Start is enabled.
After pressing the START keypad, the door will lock and the cy-
cle will begin.
©
Published by permission of the copyright owner -
DO NOT COPY or TRANSMIT

Washer Operation

End of Cycle Mode

Door Locking Mode

Door Unlocking Mode

Cycle Sequence

15
When a cycle is complete, the control will display 00 until the
washer is opened, a key is pressed, or a coin/card is entered.
When one of these three options occurs, the display will revert
back to the ready mode.
The control enters this mode after the Start pad is pressed in Start
Mode or Pause Mode to start or resume a machine cycle. The
control will stay in Door Locking Mode until the loading door is
closed and locked. The control shows the remaining cycle time
and the Door Lock LED flashes one second on/off.
Once the door is locked, the control will exit Door Locking Mode
and will enter Run Mode. If the door is opened prior to being
locked, the control will return to Start Mode.
This mode is entered when there is no time left in the cycle or
when pausing the cycle while in Run Mode. The door will unlock
after the basket stops spinning. The display will continue to flash
the remaining cycle time every second or if the next mode is End
of Cycle Mode, it will flash 01 every second. If the next mode is
Pause Mode, the display will flash PAUSE every second. If the
drive board determines that the water temperature is too hot to
drain or unlock the door, the display will flash Hot in addition to
the other displays.
The machine will always drain water down to an empty level be-
fore attempting to unlock the door. If after the programmed time
of draining, the water level is still not low enough, the control
will enter Machine Error Mode with a drain error, if enabled.
Otherwise the control will continue to drain until it sees the ma-
chine empty.
The Start key can be pressed while in this mode as long as Ma-
chine Error Mode or End of Cycle Mode is not the next mode. If
the Start key is pressed and the next mode is Pause Mode or Start
Mode, the next mode entered will be Door Locking Mode. Other-
wise the press is invalid. All other keys are invalid while in this
mode. Once Door Unlocking Mode is exited, the control will en-
ter the next mode.
Upon the start of a cycle, the control will display the total cycle
time. The appropriate LEDs will light while the machine passes
through different cycle steps. Any coin entered after the first fill
completes will be added to the total coin counter, but the user will
not be able to change cycles.
Washer Operation
Part No. 805405ENR5