Matrix 1 Led Troubleshooting - Max Megatron 1400HP Quick Install Manual

matrix 1 led troubleshooting

1. EXIT LOOP
2. CENTER LOOP
3. SAFETY LOOP
ID plug MUST be plugged in.
1400 2200
1400HP 2200HP
4. 12 VDC
5. 24 VDC
6. SECONDARY LIMIT SWITCH ON-LINE
7. PRIMARY LIMIT SWITCH ON-LINE
Matrix 1 LED
Problem Condition
"ID PLUG" LED is FLASHING on Matrix 1 and
board beeping
"POWER" LED is OFF
"BATTERY IN USE" LED is ON
"BATTERY IN USE" and "POWER" LED are
FLASHING
PRIMARY "MOTOR ON-LINE" LED is OFF
SECONDARY "MOTOR ON-LINE" LED is OFF
PRIMARY "LIMIT SWITCH ON-LINE" LED is
OFF
SECONDARY "LIMIT SWITCH ON-LINE" LED is
OFF
"UL Entrap" LED is ON
"REVERSE SENSITIVITY" LED is FLASHING
"EDGE 1" LED is ON
"EDGE 1" LED is flashing
"EDGE 2" LED is ON
"EDGE 2" LED is FLASHING
MATRIX 1
BATTERY
BACK-UP MODE
LEAVE
CLOSED
MADE in USA LEAVE OPEN
OPEN 1 TIME
AUTOMATIC OPEN/CLOSE CONTROLS
ANTI
EXIT
TAILGATE
EXIT
ON OFF
CENTER
SAFETY
MIN MAX
OFF
CLOSE TIMER
PARTIAL
OPEN
ID
PLUG
FAST POSITION
RECORDER
12VDC
GND
OBD PORT
BLACK BOX
24VDC
GND
Normal
LED
OFF • Insert ID PLUG module that is tethered to chassis into "ID PLUG" connector of Matrix 1.
15
ON • Check if AC POWER ON/OFF SWITCH is ON.
21
• Check 24 V wiring from MC-200 PRIMARY.
OFF • AC power is lost, operator is in battery back-up mode.
20
• Check if AC POWER ON/OFF SWITCH is ON.
• Measure power input DC voltage on Matrix 1 ("24V/GND" - 2-pin black connector), (expected reading
34 VDC if AC on, 25VDC if on battery back-up).
OFF / ON • Battery not plugged in to BATTERY IN port on battery charger (BC-7 module)
20 / 21
ON • Check wiring between Matrix 1 RS485 (+,-, gnd) and PRIMARY MC-200 RS485 (+,-, gnd) terminals,
9
connect [(+) to (+)], [(-) to (-)] and [GND to GND]
ON • Check wiring between Matrix 1 RS485 (+,-, gnd) and SECONDARY MC-200 RS485 (+,-, gnd) terminals,
8
connect [(+) to (+)], [(-) to (-)] and [GND to GND].
ON • Check if limit switch box is plugged into PRIMARY MC-200 "LIMIT SWITCH" input on back and MC-200
7
is powered ON.
ON • Check if limit switch box is plugged into SECONDARY MC-200 "LIMIT SWITCH" input on back and
6
MC-200 is powered ON.
OFF • An entrapment event has occurred, check if an entrapment sensor was triggered (see if EDGE 1,
16
EDGE 2, or PHOTOCELL LED is on).
OFF • An ERD event may have occurred. Check for gate obstruction.
17
• ERD sensitivity is too high for application. Re-adjust ERD setting on MC-200, (see
OFF • Sensor on EDGE 1 input (photocell or edge) may have detected an obstruction while closing gate.
13
• Photocell on EDGE 1 input is misaligned with reflector.
OFF • Sensor on EDGE 1 input (photocell or edge) may not be wired properly, (see
13
• Sensor is NOT a N.C. monitored sensor that is UL325 2016 compliant.
• Sensor might need to be re-learned.
• Sensor is damaged or malfunctioning.
OFF • Jumper between EDGE 2 and GND is missing or broken (jumper is required if a sensor is not present).
14
Sensor on EDGE 2 input (photocell or edge) may have detected an obstruction while cycling gate.
• Photocell on EDGE 2 input is misaligned with reflector.
OFF • Sensor on EDGE 2 input (photocell or edge) may not be wired properly, (see
14
• Sensor is NOT a N.C. monitored sensor that is UL325 2016 compliant.
• Sensor on EDGE 2 is damaged or malfunctioning.
• Sensor might need to be re-learned.
Table continued on next page
PRIMARY
GATE
MAGLOCK
DELAY
OPEN OPEN
MAG
LEFT RIGHT
OFF 1.5Sec 2Sec LOCK
COM
NC
Tamper NO
CENTER SAFETY GATE
COM
TAMPER
GND
Tamper IN
PHOTOCELL
UL
EDGE 1
ENTRAP EDGE 2
ID PLUG
MOTOR MOTION
ERROR
UL ALARM 12V
ALARM RET
RESET
OPEN STOP CLOSE
GND
MAX REVERSE SENSITIVITY
GATE SPEED
MOTOR OVERLOAD
OPEN
GATE
MIN
NO LIMIT SWITCH /
STATUS COM
CLAMP SLIPPING
MAX
CLOSE
LIMIT
BATTERY
SWITCH
IN USE
ON-LINE
MOTOR
POWER
ON-LINE
PRIMARY SEC
GATE GATE
8. SECONDARY MOTOR ON-LINE
9. PRIMARY MOTOR ON-LINE
Solution(s) for
Problem Condition
14
10. MAGLOCK
11. GATE TAMPER
12. PHOTOCELL
13. EDGE 1
14. EDGE 2
15. ID PLUG ERROR
16. UL ENTRAPMENT
17. REVERSE SENSITIVITY
18. MOTOR OVERLOAD
19. NO LIMIT SWITCH
CLAMP SLIPPING
20. BATTERY IN USE
21. POWER
22. GATE DISABLE
).
10
).
8
).
8
UL 325 2016 Standard-Megatron Quick Install Rev 10