Table of Contents
Advertisement
matrix 1 led continued
1. EXIT LOOP
2. CENTER LOOP
3. SAFETY LOOP
ID plug MUST be plugged in.
2200
1400
2200HP
1400HP
4. 12 VDC
5. 24 VDC
6. SECONDARY LIMIT SWITCH ON-LINE
Matrix 1 LED
Problem Condition
"PHOTOCELL" LED is ON
"PHOTOCELL" LED is FLASHING
"MOTOR OVERLOAD" LED is ON
"NO LIMIT SW / CLAMP SLIPPING" LED is ON
"EXIT" LOOP LED is FLASHING or
contstantly ON
"SAFETY" LOOP LED is FLASHING or
contstantly ON
"CENTER" LOOP LED is FLASHING or
contstantly ON
"GATE DISABLE" LED is ON
"MAG LOCK" LED is FLASHING
"GATE TAMPER" LED is FLASHING
"12VDC" LED is OFF. "24VDC" LED is OFF
MATRIX 1
BATTERY
BACK-UP MODE
CLOSED
MADE in USA
LEAVE
OPEN
AUTOMATIC OPEN/CLOSE CONTROLS
ANTI
TAILGATE
EXIT
ON
OFF
CENTER
SAFETY
MIN
MAX
OFF
CLOSE TIMER
PARTIAL
OPEN
ID
PLUG
FAST
POSITION
RECORDER
12VDC
GND
OBD PORT
BLACK BOX
24VDC
GND
7. PRIMARY LIMIT SWITCH ON-LINE
Normal
LED
OFF
•
Jumper between PHOTOCELL and GND is missing or broken (jumper is required if a sensor is not
12
present).
•
Sensor on PHOTOCELL input (photocell or edge) may have detected an obstruction while opening or
closing gate.
OFF
•
Photocell on PHOTOCELL input is misaligned with reflector.
12
•
Sensor on PHOTOCELL input (photocell or edge) may not be wired properly, (see
•
Sensor is NOT a N.C. monitored sensor that is UL325 2016 compliant.
•
Sensor on PHOTOCELL is damaged or malfunctioning.
•
Sensor might need to be re-learned.
OFF
•
Check if gate is binding against catch post or bracket in opened or closed position.
18
•
Check if gate moves manually with low resistance throughout its full range of motion.
•
Check if hinges are operational and well greased.
•
Check if operator is positioned properly relative to the gate hinge, (see
OFF
•
Gate may be too heavy for operator (check manual for maximum gate capacity).
19
•
Check if OPEN / CLOSE limit rings are tightened.
•
Check that clamp is tight on output shaft of operator.
OFF
•
Loop fault condition: Check if EXIT loop wires are connected into to loop input connector properly.
1
•
Check if loop detector is inserted properly in Matrix 1 slot.
•
Set unique loop detector frequency for each loop detector used.
•
Loop Detector might be defective. Replace defective loop detector.
NOTE: RENO loop detector LED's flash as default, but function normally (ignore the flashing).
OFF
•
Loop fault condition: check if SAFETY loop wires are connected into to loop input connector properly.
3
•
Check if SAFETY loops are wired in series.
•
Check if loop detector is inserted properly in Matrix 1 slot.
•
Set unique loop detector frequency for each loop detector used.
•
Loop Detector might be defective. Replace defective loop detector.
NOTE: RENO loop detector LED's flash as default, but function normally (ignore the flashing).
OFF
•
Loop fault condition: check if CENTER loop wires are connected into to loop input connector properly.
2
•
Check if CENTER loops are wired in series.
•
Check if loop detector is inserted properly in Matrix 1 slot.
•
Set unique loop detector frequency for each loop detector used.
•
Loop Detector might be defective. Replace defective loop detector.
NOTE: RENO loop detector LED's flash as default, but function normally (ignore the flashing).
OFF
•
Check if an external device is triggering GATE DISABLE input on Matrix 1. Disconnect devices
22
individually to determine possible false triggering of GATE DISABLE.
OFF
•
Maglock power is lost. Check if maglock power transformer is wired properly to Matrix 1 or needs to be
10
replaced.
OFF
•
Gate was manually moved off of its CLOSED position causing Tamper Relay to trigger for few seconds.
11
ON
•
Check for a short in wiring to connected device. DO NOT power external keypads or telephone entry to
4 or 5
this port (only use for radio receiver / photocell).
PRIMARY
GATE
LEAVE
MAGLOCK
DELAY
OPEN
OPEN
OPEN
MAG
1 TIME
LEFT
RIGHT
OFF
1.5Sec
2Sec
LOCK
Tamper NO
GATE
EXIT
CENTER
SAFETY
TAMPER
Tamper IN
PHOTOCELL
UL
EDGE 1
ENTRAP
EDGE 2
ID PLUG
MOTOR MOTION
ERROR
UL ALARM 12V
ALARM RET
RESET
OPEN
STOP
CLOSE
MAX
REVERSE SENSITIVITY
GATE SPEED
MOTOR OVERLOAD
GATE
MIN
NO LIMIT SWITCH /
STATUS
CLAMP SLIPPING
MAX
LIMIT
BATTERY
SWITCH
ON-LINE
MOTOR
POWER
ON-LINE
PRIMARY
SEC
GATE
GATE
8. SECONDARY MOTOR ON-LINE
9. PRIMARY MOTOR ON-LINE
15
COM
10. MAGLOCK
NC
11. GATE TAMPER
COM
GND
12. PHOTOCELL
13. EDGE 1
14. EDGE 2
15. ID PLUG ERROR
16. UL ENTRAPMENT
GND
17. REVERSE SENSITIVITY
18. MOTOR OVERLOAD
OPEN
19. NO LIMIT SWITCH
COM
CLOSE
CLAMP SLIPPING
20. BATTERY IN USE
IN USE
21. POWER
22. GATE DISABLE
Solution(s) for
Problem Condition
).
1
UL 325 2016 Standard-Megatron Quick Install Rev 10
).
8
Hide quick links:
Advertisement
Table of Contents
Troubleshooting
