Manufacturer’s Limited Warranty Before returning your Sole product to any retailer, or if you require any assistance with assembly or technical support please call us first for assistance at 866-697-6531. Thank you for your Sole purchase. TT8 -2016 Ver. D...
If you have any questions about your new product contact SOLE Fitness at 866-780-SOLE (7653). If you have a technical problem with your new treadmill contact SOLE technical service at 866-MYSOLE1 (1-866-697-6531).
Note: The clip should be attached securely to make certain it does not come off. Be familiar with its function and limitations. The treadmill will stop, depending on speed, with a one to two step coast anytime the safety key is pulled off the console. Use the red Stop switch in normal operation. TT8 TREADMILL...
Page 7
PREVENTATIVE MAINTENANCE CHART Vacuum Under Motor Cover & Clean & Inspect Deck Lubricate Deck Inspect Belt Tracking Check Wiring for Lubrication (Every 90 hours (Monthly) Adjust if Date (Every Other (Every Other Month) or sooner if dry) necessary Month) TT8 TREADMILL...
Page 8
TT8 ASSEMBLY PACK CHECKLIST HARDWARE STEP 3 #85. Ø10 x 2T #99. 5/16” x 3/4” #100. 3/8” x 2-1/4” Button Split Washer (6 pcs) Flat Head Socket Head Socket Bolt (6 pcs) Bolt (4 pcs) #131. Ø8 x Ø23 x 1.5T #102.
Page 9
#99. 5/16” x 3/4” Flat Head Socket Bolt (4 pcs) HARDWARE STEP 8 #126. M5 x 10mm Phillips Head Screw (4 pcs) ASSEMBLY TOOLS #104. Combination M5 Allen Wrench & Phillips Head Screw Driver #105. M6 L Allen Wrench TT8 TREADMILL...
TT8 ASSEMBLY INSTRUCTIONS ASSEMBLY STEP 1 1. Remove the treadmill base frame from the carton and lay it aside on firm, level ground. ASSEMBLY STEP 2 1. Locate the left and right Console Mast Tubes (5 & 4). Slide the Handrail Bottom Cover (117) onto the left and right (118) tubes as shown in the illustration.
Page 11
Incline Cable (36-47). Before attaching the hardware to Step 5, make sure the cables you just connected don’t get pinched in between the steel tubing. If they do, this may cause issues that prevent the treadmill from operating properly. TT8 TREADMILL...
Page 12
Sheet Metal Screw (6 pcs) 1. Attach the Left (117) and Right (118) Lower Handlebar Covers to the console with six Sheet Metal Screws (90). Tighten with the Combination M5 Allen Wrench & Phillips Head Screw Driver (104). TT8 TREADMILL...
Page 13
Tubes to the frame with the M6 Allen Wrench (105). Attach the console mast covers (40R & 41L) to each mast (5 & 4) with two Phillips Head Screws (126) on each side. Tighten using the Combination Allen Wrench & Phillips Head Screw Driver (104). TT8 TREADMILL...
TRANSPORTATION INSTRUCTIONS The treadmill is equipped with transport wheels that are engaged when the treadmill is folded. After folding simply roll the treadmill away. TT8 TREADMILL...
OPERATION OF OF YOUR TREADMILL GETTING FAMILIAR WITH THE THE CONTROL PANEL TT8 CONSOLE COOLING FANS SPEAKER DOT MATRIX DISPLAY CONTROL KEYS SPEED QUICK KEYS GRADE KEYS HEADPHONE JACK AUDIO IN JACK (MP3, CD, OR SMARTPHONE) CONTACT HEART RATE SENSORS...
Page 16
Stop button is held down for more than 3 seconds the console will reset. GRADE FEATURE The New Grade function of Sole TT8 make user can be stay in decline condition, The Grade level from -6 ~ 15 , When 1~15 level by...
Page 17
DOT MATRIX CENTER DISPLAY Eighteen columns of dots, 8 high for the Eighteen columns of dots, 8 high for the TT8 indicate each segment of a workout. The dots are only to show an segment of a workout. The dots are only to show an...
Page 18
Stop, Enter and Display keys for 5 seconds; the display will show: Display mode - On. Use any of the Program, Grade or Speed keys to ▲ change the setting to Off then press Enter. TT8 TREADMILL...
Sole Fitness App. Just download the free Sole Fitness App from the Apple Store or Google Play, and then follow the instructions in the App to sync with your exercise machine. This allows you to view current workout data in three different Display screens on your device.
PROGRAMMABLE FEATURES The TT8 have ten built-in programs: one Manual program, five preset profiles, one Custom, one Fit Test, and two Heart Rate programs (HR1 & HR2). PRESET PROGRAMS Hill The Hill program simulates going up and down a hill. The workload will steadily increase and then decrease during the program.
Page 21
Press Start to begin the progr gram. The program will begin with a 3 minu in with a 3 minute warm-up. If you want to bypass this and go directly tly to the beginning of the program, press Sta tart again. TT8 TREADMILL...
Page 22
6. Press the Start button to begin the workout and also save the program to memory. 7. The profile picture will be re-scaled to fit in the window, but the actual speed and grade settings will remain the same as programmed. TT8 TREADMILL...
Page 24
The score is taken from the table based on the final stage completed. After the test Cool down for about one to three minutes. Take note of your score because the console will automatically return to the start-up mode after a few minutes. TT8 TREADMILL...
80% or 60%, respectively, of your MHR on a schedule approved by your physician. Consult your physician before participating in any exercise program. TT8 TREADMILL...
Page 27
If you are feeling tired and sluggish, it is because your body needs a break. In this condition, your pace will feel harder. Again, this will show up in your RPE and you will train at the proper level for that day. TT8 TREADMILL...
8. Another Individual wearing a transmitter within 3’ of your machine’s console. If you continue to experience problems contact your dealer. WARNING! - DO NOT USE THE HEART RATE PROGRAM IF YOUR HEART RATE IS NOT REGISTERING PROPERLY ON THE TREADMILL’S DISPLAY! TT8 TREADMILL...
Page 29
HR needs to go and what kind of physical shape you are in. People who are more fit will take longer to reach the target. You can make manual adjustments to the speed throughout the program. TT8 TREADMILL...
- located under the motor cover - that connects the motor to the front roller. If that belt is loose it feels similar to the walking belt being loose. Tightening the motor belt should be done by a trained service person. TT8 TREADMILL...
Page 31
This noise is normal on new higher end belts so there is no need to contact service; the new belt just requires a wear in period. Thank you for choosing Sole and enjoy your new treadmill. TT8 TREADMILL...
Page 32
Check the belt to make sure the tension isn t too tight; adjust as necessary ’ Call your service provider to have the deck flipped if it is on the original side. The other side will have a fresh wax coating. TT8 TREADMILL...
(on a cold day) while Instructions on page 3. walking/running House circuit breaker trips, but not Need to replace the house breaker with a “High In-rush current” type breaker (see page 3 for details) the treadmill circuit breaker TT8 TREADMILL...
Page 34
CHILD LOCK - Allows you to lock the keypad so no unauthorized use of the machine is allowed. When the Child lock is enabled, the console will not allow the keypad to operate unless you press and hold the Start and Enter buttons for 3 seconds to unlock the console. TT8 TREADMILL...
Submit all service requests including serial number, contact information and a brief description of the problem online at http://www.soletreadmills.com/serviceparts.html. If you have any questions about your new product or questions about the warranty contact SOLE Fitness at 1-866-780-SOLE (7653). If you have a technical problem with your new treadmill contact SOLE technical service at 866-MYSOLE1 (697-6531).
Page 36
Before returning your Sole product to any retailer, or if you require any assistance with assembly or technical support please call us first for assistance at 866-697-6531. Thank you for your Sole purchase. TT8 TREADMILL...
Need help?
Do you have a question about the TT8 and is the answer not in the manual?
Questions and answers