Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for BullFrog SPA-562
Summary of Contents for BullFrog SPA-562
- Page 1 HOT TUB Model SPA-562 OPERATING INSTRUCTION...
- Page 2 I、 Illustration to buttons Fig.1： Control Panel “ ” “ ” Frequency up- searching / Minute On-off/Setting confirm “ ” “ ” Frequency down- searching/ Hour Radio or CD Switch/ On-off HOUR ℉ ℃ “ ” “ ” Volume up/ Set switch Blower On-off/ Switch “...
- Page 3 1、Max. with 6 KW heating system, pre-heating seting, water temperature displaying and setting 2、Max. with 2 pcs surfing pumps,1 pc circultion pump, and one pc air blower. 3、Spa light and ozone setting 4、CD audio-input / Display of radio frequency,it can be preserved 10 channels 5、Volume display and 87 volume adjusting 6、Circulation cleaning/ time set circulation cleaning 7、24 hours display and setting...
- Page 4 “ ” without stopping. The hour adjustment range is 0 0-23. when pressing HOUR “ ” It will add one minute when pressing each time and the minutes could be adjusted continually “ ” when pressing without stopping. The minute adjustment range is 00~59 The system will quit the time-setting status automatically after 6 seconds without pressing any buttons 4、Pre- circulation-cleaning Setting：...
- Page 5 3)、Press“ ” to set lasting time of circulation. It will be added 5 minutes by pressing “ ” and 1 hour by pressing“ ”each time。The maximum working time is 19 hours and 55 minutes. 4)、 Finally Press “ ” to confirme all settings . Notice: The system will be exit automatically by pressing key of “...
- Page 6 5、 ： Preheating Setting (if required) The display will show clearly whether preheating work or not. See following Fig 7-8 ： ： Fig.7： Pre-heating On 图 8： Pre-heating Off Pre- heating setting should be under the power off status. just turn on the spa , LCD will display “---”...
- Page 7 ” Notice: The system will be exit automatically by pressing key of “ 1） Pre-heating setting is turn off 2） Starting time of pre-heating 3） Lasting time of circulation 4） Preset temperature 5） Finished Chart 3 ***Notice*** 1、All setting of preheating must be in Power OFF mode, just turn on the spa，the LCD will display “---”...
- Page 8 The preheating will be turned off automatically once the preset time is finished. Or Pressing the “ ” key can stop preheating. ***Notice*** When setting temperature is lower than or equal with current water temperature ， Even preheating is on status, the circulation PUMP and HEATER are not working。...
- Page 9 PUMP3 Fig.11： Radio frequency is 105.2 MHZ，Save the present frequency to channel 3 (Save channel) or Exchange the frequency form channel 3 to the present (Searching channel) I、“ ” key is the ON/OFF key of radio and CD。and it is only available in the status of power on. The first pressing “...
- Page 10 ” key can stop the heating ,but start again the heating. During the lasting circulation cleaning,press” 13、 ： Operation of spa lights “ ” Press the key to turn ON/OFF of the the LED lights and the Fiber optic lights. 14、...
- Page 11 5.Warning Information Means for disconnection must be incorporated in the fixed wiring in accordance with the wiring rules. If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard. This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
- Page 12 Solutions of Fault Phenomenon Reason How to Solve the problem No power supply 1. The electric leakage switch was 1. Check and eliminate the malfunction, breaked off restart the spa 2. The Fuse be break off 2. Please change fuse No display on control 1.
Need help?
Do you have a question about the SPA-562 and is the answer not in the manual?
Questions and answers