[Freeze]; [Waveform Monitor] - Panasonic PT-RZ21K Operating Instructions Manual

f When anything other than [OFF] is selected, the diagnostic result is displayed in [LINK STATUS], indicating
if all the projectors including the projectors targeted for synchronization are correctly connected, and if
[MODE] is correctly set.
[LINKED]
[NO LINK]
7) Press as to select [SHUTTER SYNC].
8) Press qw to switch the item.
f The items will switch each time you press the button.
[OFF]
[ON]
Note
f The [MULTI PROJECTOR SYNC] setting item is common with the following menu item.
g The [PROJECTOR SETUP] menu → [MULTI PROJECTOR SYNC]
For details on contrast synchronization function, refer to the [PROJECTOR SETUP] menu → [MULTI PROJECTOR SYNC] (x page 162).
f The shutter synchronization function will operate when all of the following conditions are fulfilled.
g All the projectors to be linked are connected in a loop with the daisy chain connection. (Maximum 64 projectors)
g [MODE] on only one projector that is linked is set to [MASTER], and [MODE] on all other projectors are set to [SLAVE].
g [SHUTTER SYNC] on the projectors to perform the shutter synchronization is set to [ON].
f It is possible to set [SHUTTER SYNC] to [OFF] for the projectors that are linked but not to synchronize.
f The shutter operation by the shutter synchronization function will follow the setting of the [DISPLAY OPTION] menu → [SHUTTER
SETTING] on the projector that [MODE] is set to [MASTER].
f The operation of the mechanical shutter is not included in the shutter synchronization function.
f When the input signal to each linked projector is not synchronized, the timing of the shutter operation between the projectors may shift up to
1 frame while using the shutter synchronization function.
f The shutter function of the projector with [MODE] set to [SLAVE] can be operated individually. The shutter operation at this time will follow
the setting of the [DISPLAY OPTION] menu → [SHUTTER SETTING] set in that projector.
f The [3D SYNC SETTING] setting is disabled and fixed to [OFF] when [MULTI PROJECTOR SYNC] → [MODE] is set to anything other than
[OFF].
f The following settings are disabled and the contrast synchronization function and shutter synchronization function cannot be used when [3D
SYNC SETTING] is set to anything other than [OFF].
g The [PICTURE] menu → [DYNAMIC CONTRAST] → [USER] → [MULTI PROJECTOR SYNC]
g The [DISPLAY OPTION] menu → [SHUTTER SETTING] → [MULTI PROJECTOR SYNC]
g The [PROJECTOR SETUP] menu → [MULTI PROJECTOR SYNC]

[FREEZE]

Pause the projected image temporarily regardless of the playback of the external device.
1) Press as to select [FREEZE].
2) Press the <ENTER> button.
f Press the <MENU> button to release.
Note
f [FREEZE] is displayed on the screen when video is paused.

[WAVEFORM MONITOR]

Use the input signals from a connected external device to display in a waveform. Check whether video output
(luminance) signal level is within the recommended range for the projector and adjust.
1) Press as to select [WAVEFORM MONITOR].
2) Press qw to switch the item.
[OFF]
[ON]
3) Press the <MENU> button two times to clear.
4) Press as to select any horizontal line.
Chapter 4 Settings — [DISPLAY OPTION] menu
All the projectors are correctly connected, and correctly set. They are in the condition that the contrast
synchronization function or the shutter synchronization function can be used.
The projectors are not correctly connected, or not correctly set. Check the cable connection status
and the projector setting for each projector that is linked.
Select this item when the shutter synchronization function is not used.
Select this item when the shutter synchronization function is used.
Does not display the waveform monitor.
Displays the waveform monitor.
ENGLISH - 135