Download Print this page

AEG AS-IC01-4000 Installation Instructions Manual

Three-phase grid-tied solar inverter as-ic01 series and as-ic01-2 series (4 kw to 10 kw).
Hide thumbs

Advertisement

1-5
PL201708 EN LIMITED PRODUCT WARRANTY SOLAR INVERTERS - V. 1. 0
THREE-PHASE GRID-TIED SOLAR INVERTER
AS-IC01 & AS-IC01-2 (4 kW TO 10 kW)
INSTALLATION INSTRUCTIONS
PD201709 AEG GRID-TIED THREE-PHASE SOLAR INVERTER V. 1 -17 EN
Solar Solutions GmbH | Schneckenhofstrasse 19 | 60596 Frankfurt am Main | Germany | www.aeg-industrialsolar.de

Advertisement

   Related Manuals for AEG AS-IC01-4000

   Summary of Contents for AEG AS-IC01-4000

  • Page 1

    PL201708 EN LIMITED PRODUCT WARRANTY SOLAR INVERTERS - V. 1. 0 THREE-PHASE GRID-TIED SOLAR INVERTER AS-IC01 & AS-IC01-2 (4 kW TO 10 kW) INSTALLATION INSTRUCTIONS PD201709 AEG GRID-TIED THREE-PHASE SOLAR INVERTER V. 1 -17 EN Solar Solutions GmbH | Schneckenhofstrasse 19 | 60596 Frankfurt am Main | Germany | www.aeg-industrialsolar.de...

  • Page 2

    AEG GRID-TIED THREE-PHASE SOLAR INVERTER INSTALLATION MANUAL Product series: AEG grid-tied three-phase solar inverters AS-IC01-xxx and AS-IC01-xxx-2 (4 kW to 10 kW) Thank you for choosing the reliability of AEG grid-tied solar inverters! This installation manual is intended for dealers and installers involved in the planning, installation and commissioning of photovoltaic systems deploying AEG solar inverters.

  • Page 3: Table Of Contents

    3.3 Mechanical installation ..........................................17 3.3.1 Installation of three-phase inverters .................................. 18 3.4 Electrical installation ............................................ 19 3.4.1 Connection of solar modules ....................................20 3.4.2 AC connection of three-phase inverters ............................... 21 PD201709 AEG GRID-TIED THREE-PHASE SOLAR INVERTER (4-10 kW) V.1-17 EN...

  • Page 4

    6.3 AEG WiFi200 module ..........................................40 6.3.1 AEG WiFi200 product overview ................................... 40 6.3.2 Monitoring solutions .........................................41 6.3.3 Installation ............................................. 43 7. Troubleshooting ............................................... 48 8. Contact ....................................................49 9. Annex: Warranty Card ............................................50 PD201709 AEG GRID-TIED THREE-PHASE SOLAR INVERTER (4-10 kW) V.1-17 EN...

  • Page 5: Safety Precautions

    1. Safety Precautions This section describes relevant warning symbols recurring in the installation and operation manual of AEG three-phase solar inverters of the series AS-IC01 and AS-IC01-2. Icons highlight relevant information for the physical and property safety of the user. Compliance to the provided instructions is essential to prevent physical injury and product damage.

  • Page 6

    The inverter must be grounded before operation. Do not unauthorizedly open the inverter cover. The electrical parts and components inside the inverter are electrostatic. Take measurements to avoid electrostatic discharge during relevant operations. PD201709 AEG GRID-TIED THREE-PHASE SOLAR INVERTER (4-10 kW) V.1-17 EN...

  • Page 7: Delivery And Installation

    Only qualified electricians are allowed to operate the inverter under the permission of local energy authorities. Ensure reliable installation and electrical connection before operation. Do not unauthorizedly open the inverter cover during operation. The electrical parts and components inside the inverter are electrostatic. PD201709 AEG GRID-TIED THREE-PHASE SOLAR INVERTER (4-10 kW) V.1-17 EN...

  • Page 8: Maintenance And Inspection

    2. Product Overview The following section describes product appearance, packaging, accessories, technical parameters and other relevant information concerning the AEG grid-tied three-phase solar inverters of the AS-IC01 and AS-IC01-2 series. PD201709 AEG GRID-TIED THREE-PHASE SOLAR INVERTER (4-10 kW) V.1-17 EN...

  • Page 9: Solar Grid-tied Power Generation Systems

    AEG AS-IC01 and AS-IC01-2 series of three-phase grid-tied solar inverters are only deployed in solar grid-tied power generation system. The DC input is only provided by crystalline silicon solar modules whose negative and positive poles are not grounded.

  • Page 10: Product Appearance

    AEG AS-IC01 and AS-IC01-2 series of grid-tied three-phase solar inverters are meant to be deployed only with crystalline silicon solar modules. 2.2 Product Appearance 2.2.1 Three-phase inverters Figure 3: Scheme of AEG inverter AS-IC01 and AS-IC01-2 series 4000 W to 10000 W Item Instruction Cover...

  • Page 11: Labels

    The product label includes relevant information on the technical properties of the product including model name (Product Number Code), DC Input, AC Output, Protection Level, Grid standards, Certifications, and serial number of the product. PD201709 AEG GRID-TIED THREE-PHASE SOLAR INVERTER (4-10 kW) V.1-17 EN...

  • Page 12: Product Models

    Three-phase grid-tied solar inverter AS-IC01-6000-2 6000 Three-phase grid-tied solar inverter AS-IC01-8000-2 8800 Three-phase grid-tied solar inverter AS-IC01-10000-2 9800 Table 3: Current inverter models in the AEG AS-IC01 and AS-IC01-2 series PD201709 AEG GRID-TIED THREE-PHASE SOLAR INVERTER (4-10 kW) V.1-17 EN...

  • Page 13: Technical Parameters

    IEC/EN 62109-1:2010, IEC/EN 62109-2:011;, EN 61000-6-3:2007/A1:2011; VDE0126-1-1:2013, VDE-AR-N4105:2011, C10/11 Standards PV array insulation protection, PV array leakage current protection, Ground fault monitoring, Grid monitoring, Island Protection protection, DC monitoring, Short current protection Table 4: Technical parameters PD201709 AEG GRID-TIED THREE-PHASE SOLAR INVERTER (4-10 kW) V.1-17 EN...

  • Page 14: Dimensions And Weight

    The following section describes how to install and connect the inverter to the grid-tied solar system. Please ensure that all installation requirements are met before installation. Only qualified electricians are allowed to install the inverter. PD201709 AEG GRID-TIED THREE-PHASE SOLAR INVERTER (4-10 kW) V.1-17 EN...

  • Page 15: Unpacking Inspection

    1 unit Hexagon assembling bolt M5*16 2 units Communication connector 1 unit Expansion bolts M6*60 4 units 2 pairs DC connector Table 6 Packing list of AS-IC01 and AS-IC01-2 series PD201709 AEG GRID-TIED THREE-PHASE SOLAR INVERTER (4-10 kW) V.1-17 EN...

  • Page 16: Before Installation

    6. The inverter needs to be installed on a firm and sturdy surface, such as a wall, or metal brackets. The installation surface should be perpendicular to the horizontal line. Please refer to Figure 9 PD201709 AEG GRID-TIED THREE-PHASE SOLAR INVERTER (4-10 kW) V.1-17 EN...

  • Page 17

    200mm 450mm Bottom 450mm Table 8: Minimum clearance Figure 9: Installation position Do not remove any inverter part or component, otherwise damage to the device and physical injury may occur. PD201709 AEG GRID-TIED THREE-PHASE SOLAR INVERTER (4-10 kW) V.1-17 EN...

  • Page 18: Connection Cables

    As the installation place can be chosen among different construction materials, the inverter can be installed by different mounting methods. Taking the typical installation environment as the example, the manual describes how to install the inverter on concrete wall. PD201709 AEG GRID-TIED THREE-PHASE SOLAR INVERTER (4-10 kW) V.1-17 EN...

  • Page 19: Installation Of Three-phase Inverters

    4. Finally, fasten the M5 screws connecting the inverter with the bracket. For firm installation, the operators cannot release the device until the inverter is installed on the bracket firmly. PD201709 AEG GRID-TIED THREE-PHASE SOLAR INVERTER (4-10 kW) V.1-17 EN...

  • Page 20: Electrical Installation

    Figure 11: Installation of three-phase inverters 3.4 Electrical installation This section illustrates the detailed electrical installation and related safety instructions for AEG inverter series AS-IC01 and AS-IC01-2. Public Solar modules AEG solar electric grid meter inverter Monitoring Communication equipment converter...

  • Page 21: Connection Of Solar Modules

    The solar modules connected with the inverter needs to be the configured ones other than some connecting devices without authorized. Otherwise, device damage, unstable operation or fire may occur. PD201709 AEG GRID-TIED THREE-PHASE SOLAR INVERTER (4-10 kW) V.1-17 EN...

  • Page 22: Ac Connection Of Three-phase Inverters

    Fix and connect the DC output cables of the solar module with the matching DC connectors, and then connect the connectors to the inverter’s DC port. Only cables qualified according to the local electrical safety laws and regulations are allowed to be used for connection. PD201709 AEG GRID-TIED THREE-PHASE SOLAR INVERTER (4-10 kW) V.1-17 EN...

  • Page 23: Operation

    Switch on the integrated DC switch; 4. Switch on the switch on the DC side; Observe the LED indicators and information displayed on the screen. Refer to chapter 5 for detailed information. PD201709 AEG GRID-TIED THREE-PHASE SOLAR INVERTER (4-10 kW) V.1-17 EN...

  • Page 24: Stopping

    Check the ambient humidity and dust around inverter, clean Clean the surface Every six months the inverter when necessary. See Section 4.4.2 PD201709 AEG GRID-TIED THREE-PHASE SOLAR INVERTER (4-10 kW) V.1-17 EN...

  • Page 25: Maintenance Guide

    4. Repeat Section 4.1 operating content. Restart the inverter. 5. Display panel This section describes the panel display and provides instructions for display operation, including the LED indicators and the LCD display. PD201709 AEG GRID-TIED THREE-PHASE SOLAR INVERTER (4-10 kW) V.1-17 EN...

  • Page 26: Led Indicators

    Red indicator blinks every 0.5s, others are off: Hardware or software fault (E003, E004, E005, E008, E009, Unrecoverable fault Warn E011, E013 or E015). De-couple the inverter from the system Fault before maintenance. PD201709 AEG GRID-TIED THREE-PHASE SOLAR INVERTER (4-10 kW) V.1-17 EN...

  • Page 27: Operation Panel

    The inverter can be turned on and off by pressing the buttons: press "ESC" and "ENT" (about 3 seconds) at the same time; this activates the quick start-up and stop function. 5.3 LCD display LED indicators Operation panel Operation panel LCD screen Figure 15: Operation panel PD201709 AEG GRID-TIED THREE-PHASE SOLAR INVERTER (4-10 kW) V.1-17 EN...

  • Page 28: Functions Operation

    E - t o d : 0 W h $ - t o d : € 0 . 0 0 P - i n : 0 . 0 0 k W Figure 18: Monitoring parameters PD201709 AEG GRID-TIED THREE-PHASE SOLAR INVERTER (4-10 kW) V.1-17 EN...

  • Page 29: History

    Total operation time, total power produced, total power saved, total CO reduction Lifetime in lifetime Total power produced, total power saved, peak power and total CO reduction in Day statistics current day Table 17: Statistical menu PD201709 AEG GRID-TIED THREE-PHASE SOLAR INVERTER (4-10 kW) V.1-17 EN...

  • Page 30: Parameter Settings

    C a s h / p r i c e S e t M o d e l Figure 21: Statistic information Parameters can be set in this interface. LCD menus: PD201709 AEG GRID-TIED THREE-PHASE SOLAR INVERTER (4-10 kW) V.1-17 EN...

  • Page 31

    V a l / k W h : 0 0 . 5 0 € / 1 k W h the edition and press “ESC” to exit. The currency types include EUR, POD, CNY and USD. PD201709 AEG GRID-TIED THREE-PHASE SOLAR INVERTER (4-10 kW) V.1-17 EN...

  • Page 32

    E n d : 2 0 1 2 - 0 2 - 0 1 one of the system setting. The start time needs to be earlier than the end time. The setting date and time are used for statistics. PD201709 AEG GRID-TIED THREE-PHASE SOLAR INVERTER (4-10 kW) V.1-17 EN...

  • Page 33

    The default password is: 2678. MPP Start Volt The MPPT starting voltage can be set in this menu from 120V to 160V under the submenu of ”MPPT start volt”. MPPT Volt 120V PD201709 AEG GRID-TIED THREE-PHASE SOLAR INVERTER (4-10 kW) V.1-17 EN...

  • Page 34

    “ ” and “ ” to modify, and press “ENT” to confirm. ACOV Volt(phase volt) 263V ACOV Time 0.20s ACUF Freqency 47.6Hz ACUF Time 0.20s ACOF Freqency 51.4Hz ACOF Time 0.20s PD201709 AEG GRID-TIED THREE-PHASE SOLAR INVERTER (4-10 kW) V.1-17 EN...

  • Page 35

    ACOF1 and ACOF2 together for ACOF protection. ACOV Volt(phase volt) 252V ACOV Time 01.90s ACUF Frequency 49.49Hz ACUF Time 595s ACOF Frequency 50.2Hz ACOF Time 115s Run Restart Time 060s Island protect:on Table 18: Parameter settings PD201709 AEG GRID-TIED THREE-PHASE SOLAR INVERTER (4-10 kW) V.1-17 EN...

  • Page 36: System Information

    F a c t o r y C l e a r R e s t a r t Figure 25: Control interface Refer to the below table for detailed information. PD201709 AEG GRID-TIED THREE-PHASE SOLAR INVERTER (4-10 kW) V.1-17 EN...

  • Page 37

    P r e s s E S C t o c a n c e l . setting. Press “ENT” to confirm the operation or press “ESC” to return. Table 19: Inverter control PD201709 AEG GRID-TIED THREE-PHASE SOLAR INVERTER (4-10 kW) V.1-17 EN...

  • Page 38: Mode Settings

    I n i t i a l i n g … … W a i t i n g > > > > > > > Figure 27: Initialization and a list of countries will be displayed (as in Figure 28). PD201709 AEG GRID-TIED THREE-PHASE SOLAR INVERTER (4-10 kW) V.1-17 EN...

  • Page 39

    Available Countries and related grid standards. Specifications are subject to change and can be updated at any time. Country Grid standards VDE0126; VDE-AR-N4105 Germany Netherlands VDE0126/EN 50438-NL Belgium C10/C11 Other VDE0126 Table 21: Inverter control PD201709 AEG GRID-TIED THREE-PHASE SOLAR INVERTER (4-10 kW) V.1-17 EN...

  • Page 40: Monitoring Communication

    This section describes the communication connection of inverter and the inverter’s monitoring system (computers, mobile devices etc). The standard communication mode of AEG AS-IC01 and AS-IC01-2 series of grid-tied solar inverters is RS485. The RS485 port can communicate with computers and mobile devices.

  • Page 41: Optional Communication

    WiFi is the standard communication mode for the AEG AS-IC01 and AS-IC01-2. AEG WiFi200 communication module features one RS485 and one WiFi communication port for the data transmission. AEG WiFi200 features a general serial port which meets the network standards and has built-in TCP/IP protocol stack for the transformation between the user serial port and WiFi port.

  • Page 42: Monitoring Solutions

    12. Other frequency: 20MHz, 40MHz and automatic Table 23: AEG WiFi200 features AEG WiFi200 is released from factory in AP mode. It can be connected with the 485 communication interface of inverters and can be operated over computer or mobile software.

  • Page 43

    The AEG InverterControl App for Android and for Apple (iOS) devices are available on Google Play and iTunes Store respectively. For instructions on the use of the AEG WiFi200 module in combination with the dedicated apps please refer to the AEG WiFi200 Quick Installation Guide, which can be downloaded from www.aeg-industrialsolar.de...

  • Page 44: Installation

    InverterControl solar monitoring software (AEG InverterControl Web Portal / AEG InverterControl App) are needed. The AEG InverterControl App for Android and for Apple (iOS) devices are available on Google Play and iTunes Store respectively. For instructions on the use of the apps please refer to www.aeg-industrialsolar.de...

  • Page 45

    WIFI (CLIENT)-SERIAL – serial port to WIFI CLIENT WIFI (AP)-SERIAL – serial port to WIFI AP Different operation modes feature different interfaces. AEG WiFi200 supports types 3 and 4 above. PD201709 AEG GRID-TIED THREE-PHASE SOLAR INVERTER (4-10 kW) V.1-17 EN...

  • Page 46

    Client mode, it designates the remote port number and in Server mode, it designates the local port number. Network Protocol: Network Protocol type, use tcp or udp protocol Network Timeout: Network Timeout. In Server mode, there is no data during the timeout PD201709 AEG GRID-TIED THREE-PHASE SOLAR INVERTER (4-10 kW) V.1-17 EN...

  • Page 47

    Use the “Scan” button to scan the wireless hot spots information and to find the router list. The password and authentication encryption need to be set according to the attribute of the wireless router. PD201709 AEG GRID-TIED THREE-PHASE SOLAR INVERTER (4-10 kW) V.1-17 EN...

  • Page 48

    Select TCP Server in the configuration of the serial port. Input the remote IP address according to the actual. PD201709 AEG GRID-TIED THREE-PHASE SOLAR INVERTER (4-10 kW) V.1-17 EN...

  • Page 49: Troubleshooting

    Voltage-boost fault of the inverter E005 Grid OC AC overcurrent Internal AC overcurrent E006 Overtemperature Internal overtemperature Low isolation impedance of the external E007 Riso Low Low isolation impedance port system PD201709 AEG GRID-TIED THREE-PHASE SOLAR INVERTER (4-10 kW) V.1-17 EN...

  • Page 50: Contact

    MCU software version: • Fault code: • Fault description: 8. Contact Solar Solutions GmbH Schneckenhofstrasse 19 60596 Frankfurt am Main Germany www.aeg-industrialsolar.de Technical Support: Mail: inverter-support@aeg-industrialsolar.de Tel: +31 172 205 011 PD201709 AEG GRID-TIED THREE-PHASE SOLAR INVERTER (4-10 kW) V.1-17 EN...

  • Page 51: Annex: Warranty Card

    Please mail or email a copy of this warranty registration card to: Address:Solar Solutions GmbH, Schneckenhofstrasse 19, 60596 Frankfurt am main Website:www.aeg-industrialsolar.de Email:inverter-support@aeg-industrialsolar.de All rights reserved Solar Solutions GmbH. Information is subject to changes without notice. PD201709 AEG GRID-TIED THREE-PHASE SOLAR INVERTER (4-10 kW) V.1-17 EN...

Comments to this Manuals

Symbols: 0
Latest comments: