Accessories; Water Filter Certifications - Kenmore 106.5942 series Use & Care Manual

• Has the ice melted around the auger (metal spiral) in the ice
bin? Empty the ice container. Use warm water to melt the ice
if necessary.
Cut Hazard
Use a sturdy glass when dispensing ice.
Failure to do so can result in cuts.
Is the ice dispenser stalling while dispensing "crushed" ice?
Change the ice button from "crushed" to "cubed." If cubed
ice dispenses correctly, depress the button for "crushed" ice
and begin dispensing again.
Has the dispenser arm been held in too long? Ice will stop
dispensing when the arm is held in too long. Wait 3 minutes
for dispenser motor to reset before using again.
The water dispenser will not operate properly
Freezer door closed completely? Close the door firmly. If it
does not close completely, see "The doors will not close
completely."
Refrigerator connected to a water supply and the supply
shutoff valve turned on? Connect refrigerator to water
supply and turn water shutoff valve fully open.
Is the water pressure at least 30 psi (207 kPa)? The water
pressure to the home determines the flow from the dispenser.
See "Water Supply Requirements."
Kink in the home water source line? Straighten the water
source line.
• New installation? Flush and fill the water system.
• Water filter installed on the refrigerator? The filter may be
clogged or incorrectly installed.
• Is a reverse osmosis water filtration system connected to
your cold water supply? See "Water Supply Requirements."
Water is leaking from the dispenser
NOTE: One or two drops of water after dispensing is normal.
• Glass not being held under the dispenser long enough? Hold
the glass under the dispenser for 2 to 3 seconds after
releasing the dispenser lever/pad.
• New installation? Flush the water system. See "Prepare the
Water System" or "Water and Ice Dispensers."
• Recently changed water filter? Flush the water system. See
"Prepare the Water System" or "Water and Ice Dispensers."
The dispenser water is not cool enough (on some models)
NOTE: Water from the dispenser is chilled to only 50°F (10°C).
• New installation? Allow 24 hours after installation for the
water supply to cool completely.
• Recently dispensed large amount of water? Allow 24 hours
for water supply to cool completely.
• Water not been recently dispensed? The first glass of water
may not be cool. Discard the first glass of water.
• Refrigerator connected to a cold water pipe? Make sure the
refrigerator is connected to a cold water pipe. See "Water
Supply Requirements."
ACCESSORIES
Replacement Parts:
To order stainless steel cleaner or replacement filters, call
1-800-4-MY-HOME ® and ask for the appropriate part number
listed below or contact your authorized Kenmore dealer.
Stainless Steel Cleaner and Polish:
Order Part #D22 M40083 R
Base Grille Water Filter:
Order Part #9030
(T1RFKB2 or T1RFKB1 or P1RFKB2or P1RFKB1)
WATER FILTER
CERTIFICATIONS
State of California
Department of Heahh Services
Water Treatment Device
CertificateNmnber
Trademark/Model Desiffnation
04- 1606
Date issued: January 5, 2004
Date Revised. August I0, 2(_)6
ReDlacemen/Elements
Cysts
I'urbldlty
()r_anic Contaminants
l'etrachloroethyIene
Toxapbcne
R_tedServicoC_pzcity: 200gaI Rated Serviee Flow: 0.5gpr
Conditions of Certification:
Do nol use where water is mlcrohlologicaily unsa{i_ or wi_h water of unknown quahty, except that system_ certified for
cy_/reduction may, be used on disinfected watelx that may contain fiherable cysts
27