Related Manuals for ADRF Duo-i6515NM
Summary of Contents for ADRF Duo-i6515NM
- Page 1 Duo-i6515/6525/8030NM ANUAL Version 1.6 2607 Colorado Blvd. Los Angeles, CA 90041 Tel: 323-254-8131 Fax: 323-254-4928 www.adrftech.com...
- Page 2 The following is a list of abbreviations and terms used throughout this document. Abbreviation/Term Definition Automatic Gain Control Automatic Level Control AROMS ADRF’s Repeater Operation and Management System Base Transceiver Station CDMA Code Division Multiple Access Continuous Wave (unmodulated signal) Distributed Antenna System...
- Page 3 Duo-i6515/6525/8030NM User Manual V1.6 Version 1.6 (Released March 31, 2008) Information in this document is subject to change without notice. Advanced RF Technologies, Inc. 1996-2008. All rights reserved. Please send comments to: E-Mail: info@adrftech.com Phone: (323) 254-8131 (800) 313-9345 Fax: (323) 254-4928 Address: Advanced RF Technologies, Inc.
-
Page 4: Table Of Contents
Duo-i6515/6525/8030NM User Manual V1.6 ABLE OF ONTENTS 1. D 6515/6525/8030NM....................6 1.1. Introduction...................... 6 1.1.1. Highlights..................6 1.1.2. Parts List ................... 7 1.1.3. Repeater Quick View................ 8 1.2. Warnings and Hazards ..................9 2. D 6515/6525/8030NM O ................ 11 VERVIEW 2.1 Operation Modes..................... - Page 5 Duo-i6515/6525/8030NM User Manual V1.6 B: M ................35 PPENDIX ECHANICAL RAWINGS 6515/6525/8030NM O ............37 PPENDIX VERVIEW C.1 Block Diagram ....................37 C.2 Components....................38 Advanced RF Technologies, Inc. Proprietary Document Page 5 of 40...
-
Page 6: Duo-I6515/6525/8030Nm
Duo-i6515/6525/8030NM User Manual V1.6 Duo-i6515/6525/8030NM 1.1. Introduction The Duo-i6515/6525/8030NM is a dual band SMR (800 and 900 MHz) RF repeater which enhances in-building wireless coverage in the most effective and cost efficient way. For its intelligent design and versatility, the Duo-i6515/6525/ 8030NM is the ideal choice for wireless coverage problems indoors. -
Page 7: Parts List
Duo-i6515/6525/8030NM User Manual V1.6 1.1.2. Parts List Label Description iDEN Repeater AC Power Cable Ethernet Cable (cross over) Ground Cable 4 (for Duo-i6515/6525NM) Anchor Bolts or 6 (for Duo-i8030NM) Table 1 – Parts List Figure 1 – Duo-i6515/6525/8030NM Repeater Parts List ** CD includes: (1) Duo-i6515/6525/8030NM User Manual &... -
Page 8: Repeater Quick View
Duo-i6515/6525/8030NM User Manual V1.6 1.1.3. Repeater Quick View Power LED (Page12) Upper Guard Screw Soft Fail LED (Page12) (Page15) Hard Fail LED (Page12) Bracket Screw (Page15) Lower Guard Screw (Page15) Ground Hole (Page16) DC power port for external modem box Figure 2 –... -
Page 9: Warnings And Hazards
Duo-i6515/6525/8030NM User Manual V1.6 1.2. Warnings and Hazards WARNING! ELECTRIC SHOCK Opening the Duo-i6515/6525/8030NM could result in electric shock and may cause severe injury. WARNING! EXPOSURE TO RF Working with the repeater while in operation, may expose the technician to RF electromagnetic fields that exceed FCC rules for human exposure. - Page 10 Duo-i6515/6525/8030NM User Manual V1.6 WARRANTY Opening or tampering the Duo-i6515/6525/8030NM will void all warranties. Lithium Battery : CAUTION. RISK OF EXPLOSION IF BATTERY IS REPLACED BY INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO INSTRUCTIONS. Ethernet Instructions : This equipment is for indoor use only. All cabling should be limited to inside the building.
-
Page 11: Duo-I6515/6525/8030Nm Overview
In this case, the Duo-i6515/6525/8030NM works as a remote unit sending its information to the collocated external modem box. Note: ADRF’s Web GUI has not been developed for Microsoft Internet Explorer and other web browsers (e.g. Netscape, FireFox, Mozilla, etc.) may not be compatible. ADRF’s Web GUI has not been tested with Microsoft Internet Explorer versions higher than 6.0. -
Page 12: Switches & Indicators
Duo-i6515/6525/8030NM User Manual V1.6 2.2 Switches & Indicators 2.2.1. LEDs The Duo-i6515/6525/8030NM has three LEDs on the front panel of the repeater as show below in Figure 4. Figure 4 – Duo-i6515/6525/8030NM Repeater LED View POWER If the LED is lit GREEN, it indicates that there is AC power to the repeater. SOFT FAIL If the LED is lit YELLOW, it indicates that there is a soft fail alarm in the system. -
Page 13: Ac Power Switch & Dc Power Port For External Modem Box
Duo-i6515/6525/8030NM User Manual V1.6 2.2.2. AC Power Switch & DC Power Port for External Modem Box The AC Power on/off switch is located on the bottom of repeater (Figure 5). The switch should be powered on after the repeater has been installed properly. The DC Power Port can be used to provide power to the optional External Modem Box (Figure 5). -
Page 14: Installation
⑤ Make sure the Duo-i6515/6525/8030NM is securely placed onto the wall bracket ⑥ Fasten the 8 bracket screws back properly ⑦ Inspect that everything is secure * Rack Mount option is also available. Please contact ADRF for additional information. Advanced RF Technologies, Inc. Proprietary Document Page 14 of 40... - Page 15 Duo-i6515/6525/8030NM User Manual V1.6 Figure 7 – Repeater Mounting Instructions Advanced RF Technologies, Inc. Proprietary Document Page 15 of 40...
-
Page 16: Grounding
Duo-i6515/6525/8030NM User Manual V1.6 2.3.3 Grounding A ground cable is included in the packaging and should be properly connected to the repeater as shown below. Figure 8 – Ground Cable Connection Advanced RF Technologies, Inc. Proprietary Document Page 16 of 40... -
Page 17: Antenna Separation/Isolation
Duo-i6515/6525/8030NM User Manual V1.6 2.3.4 Antenna Separation/Isolation Separation between antennas is necessary to prevent oscillation. Oscillation occurs when the signal entering the system continually reenters, due to the lack of separation between the donor and server antennas. In other words, the signal is being fed back into the system. -
Page 18: Line Of Sight
Duo-i6515/6525/8030NM User Manual V1.6 2.3.5 Line of Sight The donor antenna which points towards the base station typically has a narrow beam antenna pattern. As a result, a slight deviation away from the direction of the BTS can lead to less than optimum results. In addition, obstacles between the repeater and the BTS may impair the repeater from obtaining any BTS signal. -
Page 19: Duo-I6515/6525/8030Nm Aroms Setup
Duo-i6515/6525/8030NM User Manual V1.6 Duo-i6515/6525/8030NM AROMS Setup 3.1 Repeater/PC Connection i) Wait until the Power LED is lit green. Connect the LAN cable between the laptop’s Ethernet port and the repeater’s Ethernet port. Note: Under Local Area Connection in Network Settings, make sure to select Obtain an IP address automatically under Internet Protocol (TCP/IP) properties. - Page 20 User Manual V1.6 ii) Launch MS Internet Explorer (Version 6.0) Note: ADRF’s Web GUI has not been tested for compatibility with any other web browsers (e.g. Netscape, FireFox, Mozilla, etc.). iii) Type the following IP address into the address bar of MS Internet Explorer: http://192.168.63.1/home.asp...
-
Page 21: Repeater Status
Duo-i6515/6525/8030NM User Manual V1.6 3.2 Repeater Status If you click on Status tab, the following window will appear: In this window, the user can view the following: (To change any parameters, e.g., iDEN Band, Gain Settings, you will need to go to the Install or Control window.) iDEN Band: Will display the center frequencies of the 800 and 900 MHz spectrums on the downlink and uplink respectively. - Page 22 Repeater Info: Will display repeater’s serial number, and location information (latitude and longitude coordinates). Repeater Location: Will display the address where the repeater is installed Technical Support: Will display ADRF’s technical support contact information. Installer Contact Info: Will display the installer’s name, phone and e-mail address.
-
Page 23: Repeater Control
Duo-i8030NM: 50 to 80 dB @ 0.5 dB step - Downlink AGC Level Duo-i6515NM: 5 to 15 dBm @ 0.5 dB step, default value: 15 dBm Duo-i6525NM: 15 to 25 dBm @ 0.5 dB step, default value: 25 dBm Duo-i8030NM: 20 to 30 dBm @ 0.5 dB step, default value: 30 dBm Advanced RF Technologies, Inc. - Page 24 User Manual V1.6 - Uplink AGC Level Duo-i6515NM: 5 to 15 dBm @ 0.5 dB step, default value: 15 dBm Duo-i6525NM: 15 to 25 dBm @ 0.5 dB step, default value: 25 dBm Duo-i8030NM: 20 to 30 dBm @ 0.5 dB step, default value: 30 dBm - Uplink Tracking Offset (0 to 10 dB @ 0.5 dB step, default value is 3 dB)
-
Page 25: Repeater Install
Band Selection Simply click on the desired operating bandwidth. SNMP Type in the assigned Site/Cascade ID and Manager IP Address. Default Site ID is ADRF. Default Manager IP address 100.10.10.100 Repeater Click the Install button to automatically setup the repeater. - Page 26 Duo-i6515/6525/8030NM User Manual V1.6 Repeater Location Please type in the physical address where the repeater is installed. Repeater Installer Info Please type in the installer’s name, phone number and e-mail address for technical support. Repeater Static IP: Will display the Repeater’s Static IP Address, Subnet Mask, and Gateway.
-
Page 27: Repeater System
Duo-i6515/6525/8030NM User Manual V1.6 3.5 Repeater System If you click on System tab, the following window will appear: Note: If you are the Super-User, you will see an account management section under the System Window. If you are a general user, you will not be able to see the account management portion. - Page 28 Duo-i6515/6525/8030NM User Manual V1.6 Firmware Upgrade If you click on Firmware Upgrade, the following window will appear. You can browse through your PC and locate the firmware file. Once it is selected, simply click on Update and the latest firmware will be automatically uploaded and the session will close.
-
Page 29: Maintenance Guide For Duo-I6515/6525/8030Nm
Duo-i6515/6525/8030NM User Manual V1.6 Maintenance Guide for Duo-i6515/6525/8030NM 4.1 Periodic Inspection Checklist 4.1.1 Check for loose connections to the repeater and antennas. If connections are loose, make sure that all connections are tightly fastened properly. 4.1.2 Check that cables and connectors are in good condition. 4.1.3 Ensure that the repeater brackets are in good condition and that the repeater is securely fastened. -
Page 30: Warranty And Repair Policy
Duo-i6515/6525/8030NM User Manual V1.6 Warranty and Repair Policy 5.1 General Warranty The Duo-i6515/6525/8030NM carries a Standard Warranty period of five (5) years unless indicated otherwise on the package or in the acknowledgment of the purchase order. 5.2 Limitations of Warranty Your exclusive remedy for any defective product is limited to the repair or replacement of the defective product. -
Page 31: Return Material Authorization (Rma)
Duo-i6515/6525/8030NM User Manual V1.6 5.6 Return Material Authorization (RMA) No product may be returned directly to Advanced RF Technologies, Inc. without first getting an approval from Advanced RF Technologies, Inc. If it is determined that the product may be defective, you will be given an RMA number and instructions in how to return the product. -
Page 32: Appendix A: Specifications
862 ~ 869 MHz 806 ~ 824 MHz or SMR800 UL Frequency 817 ~ 824 MHz SMR900 DL 935 ~ 940 MHz SMR900 UL 896 ~ 901 MHz Duo-i6515NM +15 dBm Composite Output Power Duo-i6525NM +25 dBm (DL/UL) Duo-i8030NM +30 dBm ≤... -
Page 33: Mechanical Specifications
Duo-i6515/6525/8030NM User Manual V1.6 A.2 Mechanical Specifications Parameters Specifications Remark Duo-i6515NM 14.13 x 18.88 x 6.42 inches Dimension Mount bracket excluded Duo-i6525NM 14.13 x 18.88 x 6.42 inches Duo-i8030NM 13.95 x 19.5 x 7.41 inches Duo-i6515NM < 38 lbs Weight... -
Page 34: Power Specifications
100 ~ 130 AC AC Frequency 45 ~ 65 Hz AC Supply Protection Fuse DC Power Option -40 ~ -60 V / +20 ~ 30 V ≤ 72 W Duo-i6515NM Power ≤ 140 W Duo-i6525NM Consumption ≤ 170 W Duo-i8030NM Ground External Threaded Stud A.5 Other Specifications... -
Page 35: A Ppendix B: M Echanical D Rawings
Duo-i6515/6525/8030NM User Manual V1.6 Appendix B: Mechanical Drawings Duo-i6515/6525NM: Advanced RF Technologies, Inc. Proprietary Document Page 35 of 40... - Page 36 Duo-i6515/6525/8030NM User Manual V1.6 Duo-i8030NM: Advanced RF Technologies, Inc. Proprietary Document Page 36 of 40...
-
Page 37: A Ppendix C D Uo - I 6515/6525/8030Nm O Verview C.1 Block Diagram
Duo-i6515/6525/8030NM User Manual V1.6 Appendix C Duo-i6515/6525/8030NM Overview C.1 Block Diagram Duo-i6515/6525/8030NM Repeater Block Diagram Advanced RF Technologies, Inc. Proprietary Document Page 37 of 40... -
Page 38: C.2 Components
Duo-i6515/6525/8030NM User Manual V1.6 C.2 Components Duo-i6515/6525NM: Noise Filter DHCP Sub Board Quad-Plexer Quad-Plexer Down Converter Up Converter Controller Interface Board Digital Filter Digital Filter Power Supply Duo-i6515/6525 Repeater Internal Components Diagram Advanced RF Technologies, Inc. Proprietary Document Page 38 of 40... -
Page 39: Advanced Rf Technologies, Inc. Proprietary Document
Duo-i6515/6525/8030NM User Manual V1.6 Duo-i8030NM Quad-plexer Quad-plexer Uplink HPA Downlink HPA Down Converter Up Converter Controller Power Supply Downlink Digital Filter for Modem Box Uplink Digital Filter Power Supply DHCP sub board Noise Filter Power port for Modem box Advanced RF Technologies, Inc. Proprietary Document Page 39 of 40... - Page 40 Duo-i6515/6525/8030NM User Manual V1.6 Power Supply It provides DC power to each module within the repeater. Controller It is responsible for monitoring the status of each module and controls its parameters. Also it interfaces with PC through Ethernet port. Down Converter Module The downlink RF signal entered through the cavity filter is converted to IF frequency, which is later converted back to RF frequency again through digital filtering.