Advertisement
RMX™ 4000
Modifying the Default IP Service
This section describes the definition of H.323 Network Service. For detailed description
of H.323, SIP and ISDN Network Service definitions, see the RMX Getting Started Guide,
"First Time Installation and Configuration".
On the RMX 4000, IPv4 is the default protocol for setting the Network Service in the
Fast Configuration Wizard.
In the Fast Configuration Wizard, select Next to move from one window to another.
1
2
3
2
Change the default service
name if required.
4
Enter the address to be
used by IP endpoints when
dialing in to the MCU.
Enter the IP address(es) of
the media card(s).
Enter the subnet mask of
the MCU.
5
Enter the IP address of the
default router.
6
In the IP Network Service creation confirmation, click OK.
Enter the name of the MCU
on the network.
7
Optional. Select Specify to
define a DNS server.
8
Click Save & Close.
Optional. Define the DNS
9
In the Success Message box confirming successful configuration, click OK.
server properties:
10 In the Reset Confirmation dialog box, click Yes.
•
Registration mode
11 In the Please wait for system reset message box, click OK.
•
The name of the MCU
System restart may take up to five minutes.
domain
12 Refresh the browser periodically until the Login screen is displayed and Login.
•
The static IP address of
In the Main Screen an MCU State indicator displays the time remaining until the
the primary DNS server
system start-up is complete.
13 Create a new User with Administrator permissions and delete the default User
(POLYCOM). For system security reasons, only when this step is completed and if
there are no System Errors, the system is fully configured and the green RDY LED
on the CNTL module (on the RMX's front panel) turns ON.
Select H.323 as the IP
Network Type.
Connecting to a Conference Directly or via Entry
The RMX is shipped with pre-configured default conferencing entities that can be used
to dial in and start conferences. Default (Transit) Entry Queue ID: 1000, default Meeting
Room IDs: 1001, 1002, 1003, and 1004.
H.323 Participants
H.323 participants dial:
[MCU Prefix in Gatekeeper][Conference or Entry Queue ID/Name]
For example, if the MCU prefix in gatekeeper is 925, you can dial to the default (Transit)
Select Specify to configure
Entry Queue by entering 925 or 9251000 and be routed to Meeting Rooms by entering its
the gatekeeper parameters.
ID (i.e. 1001, 1002, 1003 or 1004). You can connect directly to one of the default Meeting
Enter gatekeeper's host
Rooms, by dialing its number, for example: 9251001.
name or IP address.
Alternatively, you can use the Entry Queue or conference name to connect directly to
Enter the string with which the
the conference. For example, if the conference name is Maple_Room, the participant can
MCU registers itself with the
dial: 925Maple_Room.
gatekeeper.
Enter the alias that identifies
SIP Participants
the RMX's Signaling Host
The dialing string is composed of the conference routing name as registered with the
within the network. Up to five
SIP server and domain name in the format: conference_name@domain_name
aliases can be defined for
each RMX.
For example, if conference routing name is 1001, the string is 1001@polycom.com.
ISDN and PSTN Participants
ISDN and PSTN participants can connect to conferences and Meeting Rooms directly or
Optional. Modify the default
via an Entry Queue by dialing one of the numbers (including the country and area code
settings of the system flags
if needed) assigned to the conference, Meeting Room or Entry Queue. When connecting
that define the general
to an EQ they are routed to their conference according to the conference ID. For
system behavior such as the
example, if the assigned dial in number is 4045555, the ISDN/PSTN endpoint dials this
number of digits in the
number with the appropriate area code (for example, 678) and country code (001).
conference ID assigned by
the MCU.
Conference Control Using DTMF Codes
These flags can be modified
later, if required, by selecting
the System Configuration
option from the Setup menu.
Operation
Mute My Line
Unmute My Line
Increase Broadcast Volume
Decrease Broadcast Volume
Play Help Menu
Start Click&View to modify
personal layout
Queue (EQ)
DTMF String
Operation
DTMF String
*0
*6
Request individual
assistance
#6
Request assistance for
00
conference
*9
Increase Listening Volume
*76
#9
Decrease Listening Volume
#76
*83
Change To Chairperson
*78
**
Show Number of
*88
Participants
DOC2554A
Advertisement
