Advertisement
Quick Links
Vince Ottoman Bed Frame
Assembly Instructions
Dimensions
Depth x Width x Height
213cm x 148cm x 111cm (Double)
223cm x 163cm x 111cm (King)
Important
– Please read these instructions fully before starting assembly
f I
o y
u
n
e
e
d
h
e
p l
r o
Argos = 0345 6400800
- Please keep for future reference
h
a
e v
d
a
m
a
g
e
d
r o
i m
s s
n i
g
p
a
s t r
c ,
l l a
h t
e
Customer Helpline:
355/4845
330/7281
Issue 1 - 01/12/14
Advertisement
Related Manuals for hygena Vince Ottoman Bed Frame
Summary of Contents for hygena Vince Ottoman Bed Frame
- Page 1 Vince Ottoman Bed Frame Assembly Instructions - Please keep for future reference 355/4845 330/7281 Dimensions Depth x Width x Height 213cm x 148cm x 111cm (Double) 223cm x 163cm x 111cm (King) Important – Please read these instructions fully before starting assembly...
- Page 2 Safety and Care Advice Important – Please read these instructions fully before starting assembly • To reduce • Check you have all the • Assemble the item as close components and tools listed on to its fi nal position (in the same the likelihood of the following pages.
- Page 3 Components - Panels If you have damaged or missing components, call the Customer Helpline: Argos = 0345 6400800 Please check you have all the panels listed below Right side rail Headboard Left side rail Left side bar Footboard Right side bar Front bar Rear bar Middle bar...
-
Page 4: Tools Required
Components - Fittings Please check you have all the fittings listed below Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required. 12mm Bolt x 4 19mm Bolt x 8 19mm Bolt x 16 29MM Bolt x 12 34mm Bolt x 4... - Page 5 Assembly Instructions Step 1 Assemble slat frame Fix side bars & to front bar and rear using bolts Fix middle bar to front and rear bar using bolts Note: Make sure the arrows on side bars & middle bar are pointed to the front bar.
- Page 6 Assembly Instructions Step 2 & Fix side rails headboard footboard using bolts Follow step A-B-C. Important note: Do not fully tighten bolts at this stage. Step 3 Fix bottom support bar to side rails using bolts...
- Page 7 Assembly Instructions Step 4 Fix pistons to the lifting mechanism using nuts Note: Make sure the the pistons are placed as the figure shown. Step 5 Place the assembled unit as shown. Fix corner brackets to headboard and side rails using bolts shown.
- Page 8 Assembly Instructions Step 5 - continued Fix corner brackets to footboard and side rails using bolts shown. Important note: Important note: After all the parts are positioned, you Make sure the side can now fully tighten all bolts fixed on previous steps. with label faces top.
- Page 9 Assembly Instructions Step 7 Fix the assembled slat frame onto the lifting mechanism using plain washers and bolts Fix leg under the millde bar using bolt Step 8 Push the slat frame down. Continued on next page.
- Page 10 Assembly Instructions Step 8 - continued Slot the slats the slat caps & then insert it to the slat frame Step 9 Tie the strap to the end of the middle bar as shown. Assembly is complete.
- Page 11 Assembly Instructions Additional information The headboard can be opened for storage.
- Page 12 Important Ottoman Safety Warnings • Caution. This bed uses a pressurised mechanism. • Use caution when operating - Always use two hands at arm’s length, and only where illustrated on the product. • You must ensure the mattress is on the bed frame before lifting the mechanism - Failure to do so may result in injury.
Need help?
Do you have a question about the Vince Ottoman Bed Frame and is the answer not in the manual?
Questions and answers