Omron E5CN-H Communications Manual page 57
Digital controllers
Hide thumbs
Also See for E5CN-H:
- Datasheet (23 pages) ,
- Instruction manual (2 pages) ,
- User manual (374 pages)
Table of Contents
Advertisement
SECTION 3 Communications Data for CompoWay/F and SYSWAY
Variable
Address
Parameter name
type
C3 (83)
0020
Auxiliary Output 2 Open in Alarm
C3 (83)
0021
Alarm 2 Hysteresis
C3 (83)
0022
Auxiliary Output 3 Open in Alarm
(See note 1.)
C3 (83)
0023
Alarm 3 Hysteresis (See note 1.)
C3 (83)
0024
HB ON/OFF
C3 (83)
0025
Heater Burnout Latch
C3 (83)
0026
Heater Burnout Hysteresis
C3 (83)
0027
ST Stable Range
α
C3 (83)
0028
C3 (83)
002B
Input Digital Filter
C3 (83)
002C
Additional PV Display
C3 (83)
002D
MV Display
C3 (83)
002E
Automatic Display Return Time
C3 (83)
002F
Alarm 1 Latch
C3 (83)
0030
Alarm 2 Latch
C3 (83)
0031
Alarm 3 Latch (See note 1.)
C3 (83)
0032
Move to Protect Level Time
C3 (83)
0033
Input Error Output
C3 (83)
0034
Cold Junction Compensation Method
C3 (83)
0035
MB Command Logic Switching
(See note 2.)
Note:
The alarm function can also be used in Controllers without alarm output terminals. In this case, confirm alarm occurrences
via the status data.
Note 1:
Not displayed on the Controller display when Alarm 3 is not assigned to the output.
Note 2:
The logic is switched only in the MB command (SYSWAY). The logic of CompoWay/F operation command code 00
(communications writing) is not affected.
3-8
Setting (monitor) value
H'00000000 (0): Close in alarm
H'00000001 (1): Open in alarm
Temperature: H'00000001 to H'00007E90 (0.1 to 3240.0)
Analog: H'00000001 to H'0000270F (0.01 to 99.99)
H'00000000 (0): Close in alarm
H'00000001 (1): Open in alarm
Temperature: H'00000001 to H'00007E90 (0.1 to 3240.0)
Analog: H'00000001 to H'0000270F (0.01 to 99.99)
H'00000000 (0): OFF
H'00000001 (1): ON
H'00000000 (0): OFF
H'00000001 (1): ON
H'00000001 to H'000001F4 (0.1 to 50.0)
H'00000001 to H'00007E90 (0.1 to 3240.0)
H'00000000 to H'00000064 (0.00 to 1.00)
H'00000000 to H'0000270F (0.0 to 999.9)
H'00000000 (0): OFF
H'00000001 (1): ON
H'00000000 (0): OFF (display of manipulated variable OFF)
H'00000001 (1): ON (display of manipulated variable ON)
H'00000000 (0): OFF
H'00000001 to H'00000063 (1 to 99)
H'00000000 (0): OFF
H'00000001 (1): ON
H'00000000 (0): OFF
H'00000001 (1): ON
H'00000000 (0): OFF
H'00000001 (1): ON
H'00000001 to H'0000001E (1 to 30)
H'00000000 (0): OFF
H'00000001 (1): ON
H'00000000 (0): OFF
H'00000001 (1): ON
H'00000000 (0): OFF
H'00000001 (1): ON
Level
Advanced
function
setting
Initial
setting
Advanced
function
setting
Initial
setting
Advanced
function
setting
Advertisement
Table of Contents
