Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for dallmeier DDZ4120HD-SMDDZ4130HD-SMDDZ4220HD-SMDDZ4230HD-SM
Summary of Contents for dallmeier DDZ4120HD-SMDDZ4130HD-SMDDZ4220HD-SMDDZ4230HD-SM
- Page 1 DDZ4X(20)(30)HD-SM Commissioning English 005921 / 1.0.2 / 2016-12-20...
- Page 2 All trademarks identified by ® are registered trademarks of Dallmeier electronic. Third-party trademarks are named for information purposes only. Dallmeier electronic respects the intellectual property of third parties and always attempts to ensure the complete identifi- cation of third-party trademarks and indication of the respective holder of rights.
-
Page 3: Table Of Contents
5 General Notes Scope of Delivery Transportation and Packaging Warranty Approvals/Certifications Appropriate Use Operation 6 Requirements Ambient Conditions Power Supply 7 Maintenance 8 Installation and Commissioning 9 Pin Assignment Power In LAN / PoE Audio Out/In Alarm In / Relay Out / RS485 10 Technical Specifications 11 Dimensions www.dallmeier.com... -
Page 4: Validity
Always follow the instructions, notes and warnings and observe the tech- nical specifications in the product data sheet. Keep all documents in legible condition and in a suitable location for future reference. Regularly check the website www.dallmeier.com for the latest updates on product documentation. www.dallmeier.com... -
Page 5: This Document
The target audience of the document is trained system integrators. Configuration The document “Configuration” contains detailed descriptions on the con- figuration of the device. The target audience of the document is trained system integrators. www.dallmeier.com... -
Page 6: Typographical Conventions
WARNING indicates a hazardous situation which, if not avoided, could result in death or serious injury. CAUTION CAUTION indicates a hazardous situation which, if not avoided, could result in minor or moderate injury. NOTICE NOTICE is used to address practices not related to physical injury. www.dallmeier.com... - Page 7 “Expressions” in quotation marks generally indicate a control element on the device (switches or labels) or on its user interface (buttons, menu items). Paragraphs in italics provide information on basic principles, special features and efficient procedures as well as general recommenda- tions. www.dallmeier.com...
-
Page 8: Safety Instructions
• Modifications Do not make any modifications to the hardware or software that have not been tested and approved by Dallmeier. Inappropriate modifications may cause malfunctions, damages and data loss and may result in the loss of warranty. - Page 9 To avoid damage to the device by electrical surge during lightning storms, all protective measures, which are specified by the currently valid DIN, VDE and ISO standards and which provide for a standard- compliant lightning protection equipotential bonding, are mandatory and must be fulfilled by all means. www.dallmeier.com...
- Page 10 The device may only be opened by qualified personnel for commission- ing, inspection, maintenance and repair. • Disposal Do not dispose waste electrical and electronic equipment into the household trash. Disconnect the device from the power supply. Remove all connected devices. Return the device to your respective sales partner. www.dallmeier.com...
-
Page 11: General Notes
Transportation and Packaging Store the original packaging for later transportation. Dallmeier is not responsible for any damage resulting from unprofes- sional/improper transportation. The device should only be shipped in the original packaging. If the original packaging is no longer available, ensure that the used pack- aging sufficiently protects the device against damage, moisture, heat and cold. -
Page 12: Warranty
The following approvals/certifications were valid for the device at the time of this document’s compilation: • CE, FCC, DIN 50130-4 compliant Visit www.dallmeier.com for possible updates. Note (USA) This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. -
Page 13: Operation
• with strong heat emissions (e.g. radiator), • with improper ambient temperatures, • near sources with strong radiation (e.g. radio transmitters, magnetic fields), • with corrosive surroundings (e.g. gases, salt water), • with insufficient air ventilation (e.g. closed cabinet). www.dallmeier.com... -
Page 14: Power Supply
NOTICE Damage to the device resulting from improper power supply ➡ Always ensure the correct polarity when using a separate power supply unit. ➡ Do not use PoE (Power over Ethernet) and a separate power sup- ply unit simultaneously. www.dallmeier.com... -
Page 15: Maintenance
• Do not rub the plastic bubble with a dry cloth. • Do not use common glass cleaners. • Do not use microfiber cleaning cloths. • Avoid excessive rubbing. • Dry gently with a clean dry cloth (e.g. glasses cleaning cloth) to avoid scratching the surface coating. www.dallmeier.com... -
Page 16: Installation And Commissioning
• Mounting ring (included in delivery) • Marking tool (e.g. awl or pencil) • Drilling machine (for expansion nylon plug S6) • 3× Screw anchor (included in delivery) • 3× Mounting screw (included in delivery) • Screwdriver for cross recessed mounting screws www.dallmeier.com... - Page 17 ➡ If necessary, loosen (counter-clockwise) the locking screw of the housing ring. • For loosening the locking screw, use the supplied hexagon socket screw key (wrench size 1.3). • Do not fully unscrew the locking screw in order to avoid losing the screw. www.dallmeier.com...
- Page 18 DDZ4X(20)(30)HD-SM ❷ ➡ Unscrew (counter-clockwise) and remove the housing ring. • Do not touch the bubble with bare fingers. Always use the provided pair of gloves to prevent fingerprints. www.dallmeier.com...
- Page 19 DDZ4X(20)(30)HD-SM ❸ ➡ Carefully remove the PTZ dome camera from the housing base while pushing/compressing both locking tabs. www.dallmeier.com...
- Page 20 DDZ4X(20)(30)HD-SM www.dallmeier.com...
- Page 21 DDZ4X(20)(30)HD-SM ❹ ➡ Remove the adhesive tape and the lens protection cap. www.dallmeier.com...
- Page 22 ❺ ➡ Find the best mounting position for your PTZ dome camera. ➡ Place the supplied mounting ring on the ceiling and mark the drill holes (3×). ➡ Drill the mounting holes for the mounting ring into the ceiling. www.dallmeier.com...
- Page 23 DDZ4X(20)(30)HD-SM ➡ Attach the mounting ring to the supporting structure (ceiling). • Use the supplied mounting screws and screw anchors (however, remember to only use screws and anchors suitable for your ceil- ing material). www.dallmeier.com...
- Page 24 DDZ4X(20)(30)HD-SM ❻ ➡ Remove the cable entry rubber grommet from the bottom side of the housing base. www.dallmeier.com...
- Page 25 DDZ4X(20)(30)HD-SM www.dallmeier.com...
- Page 26 DDZ4X(20)(30)HD-SM ➡ Run the required cables through the cable entry rubber grommet. www.dallmeier.com...
- Page 27 DDZ4X(20)(30)HD-SM ➡ Re-attach the cable entry rubber grommet to the bottom side of the housing base as illustrated above. www.dallmeier.com...
- Page 28 DDZ4X(20)(30)HD-SM ❼ ➡ Open the cover inside the housing base. www.dallmeier.com...
- Page 29 DDZ4X(20)(30)HD-SM www.dallmeier.com...
- Page 30 ➡ Attach the housing base to the mounting ring. • Align the wide openings of the three keyhole-shaped slots on the bottom side of the housing base with the three pre-assem- bled flat-head screws A of the mounting ring. www.dallmeier.com...
- Page 31 DDZ4X(20)(30)HD-SM 3× Slotted flat-head screw with shoulder (DIN 923) www.dallmeier.com...
- Page 32 3× Slotted flat-head screw with shoulder (DIN 923) Indexing plunger with rest position (knob) ➡ Rotate the housing base counter-clockwise as far as it will go (the indexing plunger B automatically engages when the final position has been reached). www.dallmeier.com...
- Page 33 (the indexing plunger B must be engaged). To remove the housing base, pull and rotate the knob of the indexing plunger B by 90°. Then, the housing base can be unhinged by clockwise rotation. www.dallmeier.com...
- Page 34 ➡ Ensure that the separate power supply unit or the PoE switch are not connected to the mains socket at this moment. ➡ Connect the required cables to the connectors inside the housing base (see chapter “Pin Assignment” on page 41). www.dallmeier.com...
- Page 35 DDZ4X(20)(30)HD-SM ❿ ➡ Close the cover of the housing base. www.dallmeier.com...
- Page 36 DDZ4X(20)(30)HD-SM ⓫ ➡ Carefully insert the PTZ dome camera into the housing base until it clicks twice into place (ensure the correct alignment of the con- nectors). www.dallmeier.com...
- Page 37 DDZ4X(20)(30)HD-SM ➡ Make sure that both locking tabs are clicked into place. ➡ Check that the PTZ dome camera is securely fixed. www.dallmeier.com...
- Page 38 DDZ4X(20)(30)HD-SM ⓬ ➡ Fit the housing ring on the housing base and turn it in clockwise direction until it is tight. www.dallmeier.com...
- Page 39 DDZ4X(20)(30)HD-SM ⓭ Locking screw (included in delivery): Hexagon socket set screw with cone point DIN 914 M 2.5 × 4 mm ➡ Insert the locking screw of the housing ring into the provided thread (as illustrated above). www.dallmeier.com...
- Page 40 For this purpose, use the supplied hexagon socket screw key (wrench size 1.3). ➡ Finally, connect the separate power supply unit or the PoE switch to the mains socket. The device starts booting and is ready for operation after a short self- test. www.dallmeier.com...
-
Page 41: Pin Assignment
In order to comply with UL’s requirements, always use a UL-certified, Limited Power Source (LPS) Class 2 power supply unit when operat- ing the device with a separate power supply unit. Do not use PoE (Power over Ethernet) and a separate power supply unit simultaneously. www.dallmeier.com... -
Page 42: Lan / Poe
2× 3.5 mm phone jack (each for mono TS plug) Green TS (Line Out, mono) Pink TS (Mic In/Line In, mono) Signal Signal Sleeve Ground Ground NOTICE Unavailable audio signals due to improper cabling/connections ➡ Always use a ground loop isolator (with galvanic isolation) for both the Audio In and the Audio Out interface. www.dallmeier.com... -
Page 43: Alarm In / Relay Out / Rs485
Relay Out Relay Out Alarm In 1 Alarm 1 GND Alarm In 2 Alarm 2 GND Alarm In 3 Alarm 3 GND Alarm In 1 – 3 For use with potential-free switch contacts. Relay Out Max. 30 V DC, 1A; no AC. www.dallmeier.com... -
Page 44: Technical Specifications
1× RJ45 female connector Ethernet 10BASE-T/100BASE-TX (PoE+) Power In 1× Weidmüller male connector SL 3.50/02/90G * 1× Weidmüller male connector S2L 3.50/12/90G Electrical Data Voltage supply 24 V AC ±10 % (50/60 Hz) or via PoE+ PoE standard IEEE 802.3at Power consumption Max. 25 W www.dallmeier.com... - Page 45 −10 °C to +50 °C (14 °F to 122 °F) temperature Relative humidity 0% – 90% RH, non-condensing Approvals/Certifications Type CE, FCC, DIN EN 50130-4 compliant For detailed technical specifications of the respective device and pos- sible updates, read the current technical product data sheet that is available on www.dallmeier.com. www.dallmeier.com...
-
Page 46: Dimensions
DDZ4X(20)(30)HD-SM 11 Dimensions Ø 179 mm (7.05") Ø 156 mm (6.14") www.dallmeier.com... - Page 48 Dallmeier electronic GmbH & Co.KG Bahnhofstr. 16 · 93047 Regensburg · Germany Phone +49 941 8700-0 · Fax +49 941 8700-180 www.dallmeier.com · info@dallmeier.com...