ADJ ELEMENT QA User Instructions page 17

Element Hex
This unit can only be controlled using WiFly. Your DMX controller must
be connected to a ADJ WiFly Transceiver to use this function. You are
able to communicate up to 2500 feet/760 meters (open line of sight).
1. Follow the instructions on page 30 to set the WiFly address and to
activate WiFly. The address must match the address set on the
WiFly WiFly Transceiver.
2. After you have set the WiFly address, follow the DMX instructions
on page 29 to select your desired DMX Channel mode and set
your DMX address.
3. Apply power to the ADJ WiFly Transceiver. The fixture must be set
up first before you apply power to WiFly Transceiver.
4. If everything is set up properly and the fixture is receiving a
Wireless signal, you should now be able to control it with a DMX
controller.
Element Hex
Master-Slave Configuration:
This function will allows you to link units together to run in a Master-
Slave setup. In a Master-Slave set up one unit will act as the control-
ling unit and the others will react to the controlling units built-in pro-
grams. Any unit can act as a Master or as a Slave however, only one
unit can be programmed to act as the "Master."
1. Follow the instructions on page 30 to set the WiFly address and to
activate WiFly. The addresses on each fixture must be the same.
2. After you have set the WiFly address, select your "Master" unit
and set your desired operating mode.
3. For the "Slave" unit(s), put the unit in Slave mode. See page 31
Master-Slave configuration to set the unit as a Slave.
4. If everything is set up correctly, the "Slave" units will start follow-
ing the "Master" unit.
ADJ Products, LLC - www.adj.com - Element QA User Manual Page 32
WiFly Set Up
WiFly Master-Slave Set Up
Element QA
The UC IR (sold separately) infrared remote gives you control of
various functions (See below). To control the fixture you must aim the
remote at the front of the fixture and be no more than 30 feet away.
To use the ADJ UC IR you must first activate the fixtures infrared sen-
sor, to activate the sensor please see the instructions on page 30.
The Airstream IR (sold separately) remote transmitter plugs into the
headphone jack of your iOS phone or tablet. To control your IR fixture
you must raise the volume to the maximum on your iOS phone or tab-
let and aim the transmitter at the fixture sensor and be no more than
15 feet away. After you have purchased the Airstream IR transmitters,
the app is a free download from the app store for your iOS phone
or tablet. The app comes with 3 pages of control depending on the
fixture you are using. Please see below for IR functions including the
corresponding app page.
Works with App page 1.
STAND BY - Pressing this button will blackout the fixture. Press the button
again to return to the initial state.
FULL ON - Press this button to fully light up the unit.
FADE/GOBO - This button activates color change mode, color fade mode
and color chang/fade mode. Each press of the button will cycle through the
modes.
"DIMMER +" and "DIMMER -" - Use these buttons to adjust the output in-
tensity in color mode.
STROBE - Press this button to activate strobing. Use buttons 1-4 to adjust
the strobe speed. "1" being the slowest, "4" being the fastest.
COLOR - Press this button to activate color mode. Use buttons 1-9 to find
your desired color.
1-9 - Use buttons 1-9 to select your desired color in static color mode or
your desired color fade mode and color change mode. In color fade mode
and color change mode, press the Show 0 button to activate show 10. Press
the 1 button twice to activate show 11.
SOUND ON & OFF - Use the buttons to activate and deactivate sound ac-
tive mode.
SHOW 0 - See buttons 1-9.
ADJ Products, LLC - www.adj.com - Element QA User Manual Page 33
UC IR & Airstream App Control