Page 2
2. All non-wear item parts purchased after warranty expiration are warranted for 90 days. 3. Warranty starts from the date of sale to the consumer or, at Tornado’s discretion, 6 months after the dealer purchased the unit from Tornado, whichever comes first.
Your new Tornado unit is a high quality, precision-made product. All parts used in the manufacturing of this unit have passed rigid quality control standards prior to assembly. Please safeguard the original receipt / invoice. If you experience any problems with your unit during the warranty period, the original receipt / invoice will act as proof of purchase.
LEGEND MACHINE 14. LEVER SOLUTION VALVE 1. SOLUTION TANK 15. LEVER BRUSHES BASE GROUP LIFTING 2. RECOVERY TANK (only version with hydraulic pump) 3. INSPECTION CAP RECOVERY TANK 16. LEVER PARKING / EMERGENCY BRAKE 4. PLUG EXHAUST HOSE RECOVERY TANK 17.
INTRODUCTORY COMMENT Do not place any liquid contain- - Where parts are required, ask This floor cleaning machine is ers onto the machine. for ORIGINAL spare parts to the used for the industrial and civil - Storage temperature: between distributor and/or to an autho- cleaning and is able to clean -25°C and +55°C rized dealer.
Symbol denoting the solu- Symbol denoting the tion valve. brake. Indicates the solution Indicates the signal lamp valve lever. Indicates the of the brake on. signal lamp of the sole- noid valve functioning. Symbol denoting the brake. Symbol denoting the Indicates the lever of the brush.
BEFORE USE Before rotating it, it is necessary BATTERY INSTALLATION AND HANDLING OF THE PACKED SETTING OF THE BATTERY MACHINE 1. Bring the machine on a lev- TYPE The machine is supplied with elled surface. The machine is equipped either suitable packing fore-seen for 2.
All installation and maintenance ON-BOARD BATTERY RE- operations must be executed by CHARGER (OPTIONAL) specialized staff, using suitable If the machine is equipped with protection accessories. the on-board battery recharger For batteries installation it is (see under "OPTIONAL AC- necessary to reach the battery CESSORIES”) please refer to compartment as indicated under the instructions of the construc-...
1. The version (for example HOUR METER A003) of software installed on The machine is equipped with ATTENTION: the machine. an hour meter located on the 2. The setting of the battery same display of the battery Never charge a GEL battery check card is for the 24V ver- charge level indicator (1).
ADJUSTMENT OF THE Height adjustment Block the coupling levers (2) SQUEEGEE Once that the pressure and in the rear part of the brushes In order to have a perfect drying inclination of the squeegee has base group to the rings placed result through the squeegee, been adjusted, it is necessary to at the extremity of the metal...
With the brushes base group in FLOOR CLEANING lifted position, insert the brushes CONNECTION OF THE BAT- into their plate seat underneath TERIES TO THE MACHINE the brushes base turning them Once that the battery recharging until the three metal buttons are has been completed: properly seated in their slots;...
3S “SOLUTION SAVING SYS- STARTING OF THE MACHINE 10. During the first metres TEM” (OPTIONAL) 1. Turn the key (9) clockwise. check that the squeegee ad- The need of an increasing 2. Check the battery type and justment guarantees a perfect carefulness to the environment, the charge level on the display drying action and that the deter-...
ATTENTION: This control blocks the ma- chine immediately. The emer- gency brake functions also as a parking brake. To start again to work, release the lever by ATTENTION: unblocking the parking button SECURITY DEVICE REVERSE on the lever itself and act again MOVEMENT upon the levers drive control A large sized push button (13),...
4. Lift the squeegee acting upon the lever (17). ATTENTION: 5. Bring the machine to an ap- OVERFLOW DEVICE propriate place for tanks drain- In order to avoid serious dam- ing. ages to the suction motor, the 6. Turn the key (9) counterclock- machine is equipped with a wise.
BRUSHES DISASSEMBLY 2. Disassemble the squeegee The machines which have the (2) from its support (1) by rotat- electrical brushes base lifting: ing the lever (4) counterclock- 1. Switch on the machine by wise and making slide the stud turning the key (9) clockwise. bolts (3) in their slots up to their 2.
TWO-MONTHLY MAINTE- Empty the solution tank, remove NANCE the fitting of the water outlet by FRONT SQUEEGEE RUBBER taking off the two screws which CHECK fix it to the tank. Clean the in- Check the wear of the squee- side part of the fitting of dirt and gee rubber and eventually debris.
5. If the machine is equipped with the 3S system (see un- der “3S SYSTEM SOLUTION SAVING SYSTEM”) (optional), check that the switch of the detergent solution supply is acti- vated by choosing between the traditional adjustment system through the solution valve or the THE TRACTION MOTOR system of fixed optimum supply.
3. The detergent solution is 2. Check the adjustment of the EXCESSIVE FOAM PRODUC- insufficient: open more the solu- height and the inclination of the TION tion valve. squeegee (see section “AD- Check that low foam detergent 4. Check that the liquid deter- JUSTMENT OF THE SQUEE- has been used.
RECOMMENDED BRUSHES Material CHARACTERISTICS PPL (Polypropylene) Good wear resistance. Maintains characteristics with hot water up to 140°F (60°C). It is not hygroscopic. NYLON Excellent wear resistance, even with hot water over 140°F (60°C). It is hygroscopic. It looses its physical characteristics over time. TYNEX Nylon bristles with grains of abrasive material.
Need help?
Do you have a question about the 99732 and is the answer not in the manual?
Questions and answers