Table of Contents
Advertisement
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Tornado 99726
Summary of Contents for Tornado 99726
- Page 1 TORNADO INDUSTRIES, LLC 333 CHARLES COURT WEST CHICAGO, IL 60185 (630)-818-1300 FAX (630)-818-1301 WWW.TORNADOVAC.COM Operations & Maintenance Manual For Commercial Use Only BD 26/26 AUTOMATIC SCRUBBER MODEL NO: 99726 Form No. L9746AA 05/15 ©Tornado Industries, LLC. All rights reserved...
- Page 2 2. All non-wear item parts purchased after warranty expiration are warranted for 90 days. 3. Warranty starts from the date of sale to the consumer or, at Tornado’s discretion, 6 months after the dealer purchased the unit from Tornado, whichever comes first.
- Page 3 NOTES...
-
Page 4: Table Of Contents
SUMMARY Adjustment of the brushes pressure Brushes motor overload protection device LEGEND INSTRUMENT BOARD AND CON- Overflow device TROLS STOP THE MACHINE LEGEND MACHINE TECHNICAL DESCRIPTION DAILY MAINTENANCE Recovery tank cleaning INTRODUCTORY COMMENT Suction filter cleaning GENERAL RULES OF SECURITY Brushes cleaning SYMBOLOGY BEFORE USE... -
Page 5: Legend Instrument Board And Con- Trols
LEGEND INSTRUMENT BOARD AND CON- SWITCH WITH KEY TROLS INSTRUMENT BOARD 1. DISPLAY HANDLE BARS 2. SWITCH SPEED SELECTION LEVERS DRIVE CONTROL 3. SWITCH SUCTION MOTOR PUSH BUTTON SECURITY DEVICE RE- 4. SIGNAL LAMP BRAKE ON VERSE MOTION 5. SWITCH SOLENOID VALVE/COMMUTATOR LEVER SOLUTION VALVE 3S SYSTEM (OPTIONAL) LEVER BRUSHES BASE GROUP LIFTING... -
Page 6: Legend Machine
LEGEND MACHINE 13. REVERSE MOTION SECURITY DEVICE PUSH BUTTON 1. SOLUTION TANK 14. SOLUTION VALVE LEVER 2. RECOVERY TANK 15. BRUSH LIFTING LEVER (only version with 3. RECOVERY TANK CAP 4. DRAIN HOSE PLUG hydraulic pump) 16. PARKING / EMERGENCY BRAKE LEVER 5. -
Page 7: Technical Description
TECHNICAL DESCRIPTION BD 26 26 Cleaning width mm/in 660/26 Squeegee width mm/in 980/39 Working capacity, up to sqm/h, sqft/h 3000/32,291 Brushes diameter mm/in 2x345/2x13.5 Brushes rpm Pressure on the brushes kg/lbs. 60 max/133 max Brushes motor 600/25 Traction motor 400/13 Type of drive autom. -
Page 8: Introductory Comment
INTRODUCTORY COMMENT - Do not mix different detergents, - Where parts are required, ask for Your new Tornado unit is a high avoiding harmful odours. ORIGINAL spare parts from the quality, precision-made product. - Do not place any liquid containers... -
Page 9: Grounding Instructions
GROUNDING INSTRUCTIONS This appliance must be grounded. If it should malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the risk electric shock. This machine is equipped with a cord having an equipment -grounding conductor and grounding plug. The plug must be inserted into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances. -
Page 10: Symbology
Symbol denoting the solu- Symbol denoting the tion valve. brake. Indicates the solution Indicates the signal lamp valve lever. Indicates the of the brake on. signal lamp of the sole- noid valve functioning. Symbol denoting the brake. Symbol denoting the Indicates the lever of the brush. -
Page 11: Before Use
BEFORE USE the support of the gas shock ab- Handling of the packed machine sorber (1). The machine is supplied with suit- 7. Reassemble everything. able packing foreseen for forklift truck handling. The total weight is 562 lbs. (255kg). Packing dimensions: Base: 70”... -
Page 12: Battery Recharger
avoid their complete discharge Bat- teries must be charged within a few minutes after the battery discharge signal starts blinking. NOTE: Never leave batteries completely discharged even if the Battery charger machine is not used. If using wet ATTENTION: Be sure that the battery charger is lead batteries, please check the The machine and its battery check suitable for the installed batteries... -
Page 13: Hour Meter
3. The batteries charge level indica- Squeegee assembly tor (1) is digital. The battery charge 1. Hold the squeegee support (1) level starts at 90, which indicates slightly off of the floor. the 90% of the total charge and 2. Insert the two stud bolts (3) decreases by 10’s. -
Page 14: Splash Guard Assembly
in their slots; rotate the brush to push the button towards the cou- pling spring until they are locked in place. The figure shows the rotating direc- tion for brush coupling. ATTENTION: Brush assembly Every type of floor requires a specific adjustment. -
Page 15: Recovery Tank
To do this, it is necessary to reach STARTING OF THE MACHINE the battery compartment as indi- 1.Turn the key (9) clockwise. cated under paragraph “ACCESS 2.Check the battery type and the TO THE BATTERY COMPART- charge level on the display (1). MENT”. -
Page 16: Forward Movement
Forward movement A large-sized push button (13), Adjustment of the brush pressure The traction of the machine is placed on the rear of the machine Through the knob (1) it is possible given through an electronically is for the automatic drive reversal. to adjust the brush pressure on the controlled motor. -
Page 17: Brushes Motor Overload Protection Device
Brush motor overload protection device The machine is equipped with a protection device for the brush motor. This device locks the motor functioning in order to protect it and indicates the overload on the Daily maintenance display (1) with ”AL01”. Recovery tank cleaning Excessive brush pressure on a 1. -
Page 18: Suction Filter Cleaning
Brush cleaning ATTENTION: Disassemble the brush and clean Pick up the brushes and wash them them with a water jet (check under using gloves to protect from paragraph of “BRUSH contact with dangerous solutions. DISASSEMBLY”). Squeegee cleaning Brush disassembly Keeping the squeegee clean For machines that have the guarantees the best drying action. -
Page 19: Squeegee Hose Cleaning
2. Release the hook (9) of the Cleaning of the solution tank 4. Rinse the hose by pouring some rubber blade holder and take the 1. Bring the machine to an water into the solution tank. rubber off. appropriate place for the solution 5. -
Page 20: Cleaning Of The Inner Filter Solution Tank
Cleaning of the inner filter solution Troubleshooting guide tank The suction motor does not work Regularly clean the internal filter 1. Verify that the key switch (9) is of the solution tank that is in the in the on position. rear lower part of the machine. -
Page 21: The Machine Does Not Clean Properly
3. Check that solution filter is The machine does not clean The squeegee does not dry clean (see under paragraph properly perfectly “CLEANING OF THE 1. The brushes do not have the 1. Check that the squeegee SOLUTION FILTER”). suitable bristle dimension: contact rubbers are clean. -
Page 22: Programmed Maintenance
PROGRAMMED MAINTENANCE INTERVENTION DAILY 20 HOURS * 200 HOURS * 1000 HOURS * RECOVERY TANK CLEANING • SUCTION FILTER CLEANING • SOLUTION TANK FILTER CLEANING • BRUSHES CLEANING • BRUSHES DISASSEMBLY AND CLEANING • SQUEEGEE CLEANING • FRONT SQUEEGEE RUBBER REPLACE- •... - Page 23 MACHINE CODE QTY DESCRIPTION BD 26 26 48903010 Brush PPL 0,3 Ø 345/13in Delicate floors. 48903020 Brush PPL 0,6 Ø 345mm/13in Normal floors. 48903030 Brush PPL 0,9 Ø 345mm/13in Smooth floors with small joints and persistent dirt. 48903040 Brush TYNEX Ø 345mm/13in Floors of resistant material and particularly dirty.
- Page 24 Return to: may or may not apply based on your specific machine. If any defect occurs, the warranty is voided if Tornado Industries service is attempted by non-Authorized Tornado Service Centers. 333 Charles Ct. Unit 109 West Chicago, IL 60185 ©2015 Tornado Industries.
Need help?
Do you have a question about the 99726 and is the answer not in the manual?
Questions and answers