Mitsubishi Electric FR-E720-0.1K Instruction Manual page 41

Parameter list
Parameter Name
54 FM terminal function selection
Frequency monitoring
55
reference
56 Current monitoring reference
57 Restart coasting time
58 Restart cushion time
59 Remote function selection
Energy saving control
60
selection
61 Reference current
Reference value at
62
acceleration
Reference value at
63
deceleration
65 Retry selection
Stall prevention operation
66
reduction starting frequency
Number of retries at fault
67
occurrence
68 Retry waiting time
69 Retry count display erase
Special regenerative brake
70
duty
71 Applied motor
72 PWM frequency selection
73 Analog input selection
74 Input filter time constant
Reset selection/disconnected
75 PU detection/PU stop
selection
77 Parameter write selection
Reverse rotation prevention
78
selection
 79 Operation mode selection
80 Motor capacity
81 Number of motor poles
82 Motor excitation current
83 Rated motor voltage
84 Rated motor frequency
Speed control gain (Advanced
89
magnetic flux vector)
90 Motor constant (R1)
91 Motor constant (R2)
Motor constant (L1)/d-shaft
92
inductance
37
Setting Initial
Parameter
Range Value
1 to 3, 5,
7 to 12, 14,
1
21, 24, 52,
53, 61, 62
0 to 400Hz 60Hz
Inverter
0 to 500A rated
current
0, 0.1 to 5s,
9999
9999
0 to 60s 1s
0, 1, 2, 3 0
0, 9 0
0 to 500A,
9999
9999
0 to 200%,
9999
9999
0 to 200%,
9999
9999
0 to 5 0
0 to 400Hz 60Hz
0 to 10,
0
101 to 110
0.1 to 360s 1s
0 0
0 to 30% 0%
0, 1, 3 to 6,
13 to 16, 23,
0
24, 40, 43,
44, 50, 53, 54
0 to 15 1
0, 1, 10, 11 1
0 to 8 1
0 to 3,
14
14 to 17
0, 1, 2 0
0, 1, 2 0
0, 1, 2, 3, 4,
0
6, 7
0.1 to 15kW,
9999
9999
2, 4, 6, 8, 10,
9999
9999
0 to 500A
(0 to ****), 9999
9999 
200/400V 
0 to 1000V

10 to 120Hz 60Hz
0 to 200%,
9999
9999
0 to 50
(0 to ****), 9999
9999 
0 to 50
(0 to ****), 9999
9999 
0 to 1000mH
(0 to 50,
9999
0 to ****),
9999

Name
Motor constant (L2)/q-shaft
93
inductance
94 Motor constant (X)
96 Auto tuning setting/status
PU communication station
117
number
118 PU communication speed
PU communication stop bit
119
length
PU communication parity
120
check
Number of PU communication
121
retries
PU communication check time
122
interval
PU communication waiting
123
time setting
PU communication CR/LF
124
selection
Terminal 2 frequency setting
 125
gain frequency
Terminal 4 frequency setting
126
gain frequency
PID control automatic
127
switchover frequency
128 PID action selection
129 PID proportional band
130 PID integral time
131 PID upper limit
132 PID lower limit
133 PID action set point
134 PID differential time
145 PU display language selection 0 to 7
Built-in potentiometer
146

switching
Acceleration/deceleration time
147
switching frequency
150 Output current detection level 0 to 200%
Output current detection signal
151
delay time
152 Zero current detection level
153 Zero current detection time
Stall prevention operation
156
selection
157 OL signal output timer
 160 User group read selection
Frequency setting/key lock
161
operation selection
Automatic restart after
162 instantaneous power failure
selection
Stall prevention operation level
165
for restart
Setting Initial
Range Value
0 to 1000mH
(0 to 50,
9999
0 to ****),
9999 
0 to 100%
(0 to 500,
9999
0 to ****),
9999

0, 1, 11, 21 0
0 to 31
0
(0 to 247)
48, 96, 192,
192
384
0, 1, 10, 11 1
0, 1, 2 2
0 to 10, 9999 1
0, 0.1 to
0
999.8s, 9999
0 to 150ms,
9999
9999
0, 1, 2 1
0 to 400Hz 60Hz
0 to 400Hz 60Hz
0 to 400Hz,
9999
9999
0, 20, 21,
40 to 43, 50, 0
51, 60, 61
0.1 to 1000%,
100%
9999
0.1 to 3600s,
1s
9999
0 to 100%,
9999
9999
0 to 100%,
9999
9999
0 to 100%,
9999
9999
0.01 to
9999
10.00s, 9999
0
0, 1 1
0 to 400Hz,
9999
9999
150%
0 to 10s 0s
0 to 200% 5%
0 to 1s 0.5s
0 to 31, 100,
0
101
0 to 25s,
0s
9999
0, 1, 9999 0
0, 1, 10, 11 0
0, 1, 10, 11 1
0 to 200% 150%