1. Manuals
  2. Brands
  3. IEI Technology Manuals
  4. Motherboard
  5. NANO-BT Series
  6. User manual

IEI Technology NANO-BT Series User Manual

Hide thumbs Also See for NANO-BT Series:
Table of Contents

Advertisement

Quick Links

Download this manual See also: User Manual
NANO-BT EPIC SBC
MODEL:
NANO-BT Series
EPIC SBC with 22nm Intel® Atom™ or Celeron® SoC,
Dual GbE, DDR3, HDMI, VGA, LVDS, USB 2.0/3.0, COM Ports
Two SATA 3Gb/s Ports, IPMI 2.0 and RoHS

User Manual

Page i
Rev. 1.10 – May 28, 2015

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the NANO-BT Series and is the answer not in the manual?

Questions and answers

Related Manuals for IEI Technology NANO-BT Series

Summary of Contents for IEI Technology NANO-BT Series

  • Page 1: User Manual

    NANO-BT EPIC SBC MODEL: NANO-BT Series EPIC SBC with 22nm Intel® Atom™ or Celeron® SoC, Dual GbE, DDR3, HDMI, VGA, LVDS, USB 2.0/3.0, COM Ports Two SATA 3Gb/s Ports, IPMI 2.0 and RoHS User Manual Page i Rev. 1.10 – May 28, 2015...
  • Page 2 NANO-BT EPIC SBC Revision Date Version Changes May 28, 2015 1.10 Updated for R11 version October 1, 2014 1.03 Updated Section 1.6: Dimensions June 27, 2014 1.02 Updated supported memory specifications in Chapter 1. May 7, 2014 1.01 Updated Section 1.6: Dimensions Updated Chapter 6: Software Drivers Updated Table 3-15: LVDS Connector Pinouts April 3, 2014...
  • Page 3 NANO-BT EPIC SBC Copyright COPYRIGHT NOTICE The information in this document is subject to change without prior notice in order to improve reliability, design and function and does not represent a commitment on the part of the manufacturer. In no event will the manufacturer be liable for direct, indirect, special, incidental, or consequential damages arising out of the use or inability to use the product or documentation, even if advised of the possibility of such damages.

  • Page 4: Table Of Contents

    NANO-BT EPIC SBC Table of Contents 1 INTRODUCTION......................1 1.1 I ......................2 NTRODUCTION 1.2 M ....................3 ODEL ARIATIONS 1.3 B ........................4 ENEFITS 1.4 F ........................4 EATURES 1.5 C ......................5 ONNECTORS 1.6 D ....................... 7 IMENSIONS 1.7 D ........................
  • Page 5 NANO-BT EPIC SBC 3.2.10 Front Panel Connector .................. 29 3.2.11 IPMI LED Connector ..................30 3.2.12 iRIS Module Slot (NANO-BT-i1 Models Only) ..........31 3.2.13 LAN LED Connectors ..................32 3.2.14 LVDS Connector .................... 33 3.2.15 Memory Card Slot ..................34 3.2.16 microSD Card Slot (E38xx Models Only) ............
  • Page 6 NANO-BT EPIC SBC 4.3.1 AT/ATX Power Mode Setting ................59 4.3.2 Clear CMOS Button..................60 4.3.3 LVDS Panel Resolution Selection ..............61 4.3.4 LCD Voltage Selection ..................62 4.3.5 mSATA/SATA Selection..................63 4.3.6 PCI-104 Voltage Selection ................64 4.3.7 USB Power Select .................... 64 4.4 I ............
  • Page 7 NANO-BT EPIC SBC 5.4.1 North Bridge ....................93 5.4.1.1 Intel IGD Configuration................93 5.4.2 South Bridge..................... 96 5.4.2.1 PCI Express Configuration ............... 97 5.5 S ......................... 98 ECURITY 5.6 B ........................99 5.7 E ........................101 6 SOFTWARE DRIVERS .................... 103 6.1 S ..................
  • Page 8 NANO-BT EPIC SBC List of Figures Figure 1-1: NANO-BT........................2 Figure 1-2: Connectors (Front Side) .....................5 Figure 1-3: Connectors (Solder Side) ...................6 Figure 1-4: NANO-BT Main Dimensions (mm) ................7 Figure 1-5: NANO-BT Height Dimensions 1 (mm) ...............8 Figure 1-6: NANO-BT Height Dimensions 2 (mm) ...............8 Figure 1-7: Data Flow Diagram......................9 Figure 3-1: Connectors and Jumpers (Front Side) ..............18 Figure 3-2: Connectors and Jumpers (Solder Side) ..............19...
  • Page 9 NANO-BT EPIC SBC Figure 3-24: SATA 3Gb/s Drive Connector Locations ..............41 Figure 3-25: SATA Power Connector Locations ...............42 Figure 3-26: RS-232 Serial Port Connector Locations..............43 Figure 3-27: RS-422/485 Connector Location................44 Figure 3-28: SMBus Connector Location ...................45 Figure 3-29: SPI Flash Connector Location................46 Figure 3-30: SPI EC Flash Connector Location.................47 Figure 3-31: USB 2.0 Connector Location .................48 Figure 3-32: External Peripheral Interface Connector ..............48...
  • Page 10 NANO-BT EPIC SBC List of Tables Table 1-1: Model Variations ......................3 Table 1-2: NANO-BT Specifications....................12 Table 2-1: Packing List.........................16 Table 2-2: Optional Items......................16 Table 3-1: Peripheral Interface Connectors ................20 Table 3-2: Rear Panel Connectors ....................21 Table 3-3: CPU Power Connector Pinouts .................22 Table 3-4: Audio Connector Pinouts ..................23 Table 3-5: Battery Connector Pinouts ..................24 Table 3-6: Backlight Inverter Connector Pinouts ..............25...
  • Page 11 NANO-BT EPIC SBC Table 3-27: SPI EC Flash Connector Pinouts ................47 Table 3-28: USB 2.0 Connector Pinouts ..................48 Table 3-29: LAN1 Ethernet Connector Pinouts .................49 Table 3-30: LAN2 Ethernet Connector Pinouts .................49 Table 3-31: Connector LEDs......................50 Table 3-32: HDMI Connector Pinouts ..................51 Table 3-33: Keyboard Connector Pinouts..................52 Table 3-34: USB 2.0 Port Pinouts....................52 Table 3-35: USB 3.0 Port Pinouts....................53...
  • Page 12 NANO-BT EPIC SBC BIOS Menus BIOS Menu 1: Main ........................72 BIOS Menu 2: Advanced ......................73 BIOS Menu 3: ACPI Configuration ....................74 BIOS Menu 4: F81866 Super IO Configuration ................75 BIOS Menu 5: Serial Port n Configuration Menu...............75 BIOS Menu 6: iWDD H/W Monitor....................80 BIOS Menu 7: Smart Fan Mode Configuration ................81 BIOS Menu 8: RTC Wake Settings ....................83 BIOS Menu 9: Serial Port Console Redirection .................84...

  • Page 13: Introduction

    NANO-BT EPIC SBC Chapter Introduction Page 1...

  • Page 14: Introduction

    1.1 Introduction Figure 1-1: NANO-BT The NANO-BT series is an EPIC form factor single bard computer. It has an on-board 22nm Intel® Atom™ or Celeron® processor, and supports one 204-pin 1333/1066 MHz dual-channel unbuffered DDR3 Low Voltage (DDR3L) SDRAM SO-DIMM with up to 8.0 GB of memory.

  • Page 15: Model Variations

    NANO-BT EPIC SBC 1.2 Model Variations There are several models of the NANO-BT series. The model variations are listed in Table 1-1. Model On-board SoC Max. Operating iRIS Memory Temp. Standard NANO-BT-i1-J19001 Intel® Celeron® processor J1900 8 GB -20ºC – 60ºC...

  • Page 16: Benefits

    NANO-BT EPIC SBC 1.3 Benefits Some of the NANO-BT motherboard benefits include:  Powerful graphics with multiple monitors  Staying connected with both wired LAN connections  Speedy running of multiple programs and applications 1.4 Features Some of the NANO-BT motherboard features are listed below: ...

  • Page 17: Connectors

    NANO-BT EPIC SBC 1.5 Connectors The connectors on the NANO-BT are shown in the figure below. Figure 1-2: Connectors (Front Side) Page 5...

  • Page 18: Figure 1-3: Connectors (Solder Side)

    NANO-BT EPIC SBC Figure 1-3: Connectors (Solder Side) Page 6...

  • Page 19: Dimensions

    NANO-BT EPIC SBC 1.6 Dimensions The main dimensions of the NANO-BT are shown in the diagram below. Figure 1-4: NANO-BT Main Dimensions (mm) Page 7...

  • Page 20: Figure 1-5: Nano-Bt Height Dimensions 1 (Mm)

    NANO-BT EPIC SBC The height of the NANO-BT series varies depending on the heatsink installed on the board. Figure 1-5 shows the height dimensions of the following models:  NANO-BT-i1-E38271  NANO-BT-i1-E38261  NANO-BT-i1-E38251  NANO-BT-i1-E38151  NANO-BT-i1-N28071 Figure 1-5: NANO-BT Height Dimensions 1 (mm) Figure 1-6 shows the height dimensions of the following models: ...

  • Page 21: Data Flow

    NANO-BT EPIC SBC 1.7 Data Flow F igure 1-7 shows the data flow between the system chipset, the CPU and other components installed on the motherboard. Figure 1-7: Data Flow Diagram Page 9...

  • Page 22: Technical Specifications

    NANO-BT EPIC SBC 1.8 Technical Specifications NANO-BT technical specifications are listed below. Specification/Model NANO-BT EPIC Form Factor Intel® Atom™ processor E3845 (1.91GHz, quad-core, 2MB cache, TDP=10W) On-board SoC Intel® Atom™ processor E3827 (1.75GHz, dual-core, 1MB cache, TDP=8W) Intel® Atom™ processor E3826 (1.46GHz, dual-core, 1MB cache, TDP=7W) Intel®...
  • Page 23 NANO-BT EPIC SBC Specification/Model NANO-BT One full-size PCIe Mini card slot supports mSATA (co-lay SATA port 2) PCIe One microSD card slot (E38xx models only) microSD I/O Interface Connectors One internal audio connector (10-pin) Audio Connector One VGA port (up to 2560 x 1600, 60Hz) Display Ports One HDMI port (up to 1920 x 1080, 60Hz) 18-bit/24-bit dual-channel LVDS (up to 1920 x 1200, 60Hz)

  • Page 24: Table 1-2: Nano-Bt Specifications

    NANO-BT EPIC SBC Specification/Model NANO-BT Physical Specifications 115 mm x 165 mm Dimensions 850 g / 350 g Weight GW/NW Table 1-2: NANO-BT Specifications Page 12...

  • Page 25: Packing List

    NANO-BT EPIC SBC Chapter Packing List Page 13...

  • Page 26: Anti-Static Precautions

    NANO-BT EPIC SBC 2.1 Anti-static Precautions WARNING! Static electricity can destroy certain electronics. Make sure to follow the ESD precautions to prevent damage to the product, and injury to the user. Make sure to adhere to the following guidelines:  Wear an anti-static wristband: Wearing an anti-static wristband can prevent electrostatic discharge.

  • Page 27: Packing List

    NANO-BT EPIC SBC 2.3 Packing List NOTE: If any of the components listed in the checklist below are missing, do not proceed with the installation. Contact the IEI reseller or vendor the NANO-BT was purchased from or contact an IEI sales representative directly by sending an email to s ales@ieiworld.com The NANO-BT is shipped with the following components:...

  • Page 28: Optional Items

    NANO-BT EPIC SBC Quantity Item and Part Number Image One Key Recovery CD Quick Installation Guide Table 2-1: Packing List 2.4 Optional Items The following are optional components which may be separately purchased: Item and Part Number Image IPMI 2.0 adapter card with AST1010 BMC chip (without KVM over IP function) for PCIe Mini socket interface (P/N: iRIS-1010-R10) Dual USB cable...

  • Page 29: Connectors

    NANO-BT EPIC SBC Chapter Connectors Page 17...

  • Page 30: Peripheral Interface Connectors

    NANO-BT EPIC SBC 3.1 Peripheral Interface Connectors This chapter details all the jumpers and connectors. 3.1.1 NANO-BT Layout The figures below show all the connectors and jumpers. *CN1 is only available in E38xx models. Figure 3-1: Connectors and Jumpers (Front Side) Page 18...

  • Page 31: Peripheral Interface Connectors

    NANO-BT EPIC SBC *IPMI1 is only available in NANO-BT-i1 models. Figure 3-2: Connectors and Jumpers (Solder Side) 3.1.2 Peripheral Interface Connectors The table below lists all the connectors on the board. Connector Type Label 12 V DC input connector 4-pin connector CN10 Audio connector 10-pin header...

  • Page 32: Table 3-1: Peripheral Interface Connectors

    NANO-BT EPIC SBC Connector Type Label Fan connector (CPU) 3-pin wafer CPU_FAN1 Fan connector (system) 3-pin wafer SYS_FAN1 Front panel connector 6-pin wafer CN11 iRIS module connector Half-size PCIe Mini slot IPMI1 IPMI LED connector 2-pin header ID_LED2 LAN1 LED connector 2-pin header LAN2 LED connector 2-pin header...

  • Page 33: External Interface Panel Connectors

    NANO-BT EPIC SBC 3.1.3 External Interface Panel Connectors The table below lists the connectors on the external I/O panel. Connector Type Label Ethernet ports RJ-45 LAN1, LAN2 HDMI connector HDMI CN12 Keyboard/Mouse connector PS/2 USB 2.0 connector USB 2.0 USB 3.0 connector USB 3.0 VGA connector 15-pin female...

  • Page 34: Audio Connector

    NANO-BT EPIC SBC Figure 3-3: CPU Power Connector Location PIN NO. DESCRIPTION +12 V +12 V Table 3-3: CPU Power Connector Pinouts 3.2.2 Audio Connector CN Label: AUDIO1 10-pin header, p=2.0 mm CN Type: See Figure 3-4 CN Location: See Table 3-4 CN Pinouts: This connector connects to speakers, a microphone and an audio input.

  • Page 35: Battery Connector

    NANO-BT EPIC SBC Figure 3-4: Audio Connector Location Description Description LINE_OUTR LINEIN_R ANALOG_GND ANALOG_GND LINE_OUTL LINEIN_L ANALOG_GND ANALOG_GND MICIN1 MICIN2 Table 3-4: Audio Connector Pinouts 3.2.3 Battery Connector CAUTION: Risk of explosion if battery is replaced by an incorrect type. Only certified engineers should replace the on-board battery.

  • Page 36: Backlight Inverter Connector

    NANO-BT EPIC SBC A system battery is placed in the battery holder. The battery provides power to the system clock to retain the time when power is turned off. Figure 3-5: Battery Connector Location Description VBATT Table 3-5: Battery Connector Pinouts 3.2.4 Backlight Inverter Connector CN Label: INV1...

  • Page 37: Buzzer Connector

    NANO-BT EPIC SBC Description BRIGHTNESS2 ENABKL2 Table 3-6: Backlight Inverter Connector Pinouts 3.2.5 Buzzer Connector CN Label: 2-pin wafer, p=1.25 mm CN Type: See Figure 3-7 CN Location: The connector is connected to a buzzer. Figure 3-7: Buzzer Connector Location Page 25...

  • Page 38: Chassis Intrusion Connector

    NANO-BT EPIC SBC 3.2.6 Chassis Intrusion Connector CN Label: CHASSIS1 2-pin header, , p=2.0 mm CN Type: CN Location: F igure 3-8 See Table 3-7 CN Pinouts: The chassis intrusion connector is for a chassis intrusion detection sensor or switch that detects if a chassis component is removed or replaced.

  • Page 39: Fan Connector (Cpu)

    NANO-BT EPIC SBC Figure 3-9: Digital I/O Connector Location PIN NO. DESCRIPTION PIN NO. DESCRIPTION DOUT3 DOUT2 DOUT1 DOUT0 DIN3 DIN2 DIN1 DIN0 Table 3-8: Digital I/O Connector Pinouts 3.2.8 Fan Connector (CPU) CN Label: CPU_FAN1 3-pin wafer, p=2.54 mm CN Type: See Figure 3-10 CN Location:...

  • Page 40: Fan Connector (System)

    NANO-BT EPIC SBC Figure 3-10: CPU Fan Connector Location PIN NO. DESCRIPTION FAN_IN VCC (+12 V) Table 3-9: CPU Fan Connector Pinouts 3.2.9 Fan Connector (System) CN Label: SYS_FAN1 3-pin wafer, p=2.54 mm CN Type: See Figure 3-11 CN Location: See Table 3-10 CN Pinouts: Each fan connector attaches to a system cooling fan.

  • Page 41: Front Panel Connector

    NANO-BT EPIC SBC Figure 3-11: System Fan Connector Location PIN NO. DESCRIPTION FAN_IN VCC (+12 V) Table 3-10: System Fan Connector Pinouts 3.2.10 Front Panel Connector CN Label: CN11 6-pin wafer, p=2.0 mm CN Type: See Figure 3-12 CN Location: See Table 3-11 CN Pinouts: The front panel connector connects to the indicator LEDs on the computer's front panel.

  • Page 42: Ipmi Led Connector

    NANO-BT EPIC SBC Figure 3-12: Front Panel Connector Location DESCRIPTION DESCRIPTION PWR_LED- HDD_LED+ PWR_LED+ HDD_LED- Table 3-11: Front Panel Connector Pinouts 3.2.11 IPMI LED Connector CN Label: ID_LED2 2-pin header, p=2.0 mm CN Type: See Figure 3-13 CN Location: See Table 3-12 CN Pinouts: The IPMI LED connector is used to connect to the IPMI LED indicator on the chassis.

  • Page 43: Iris Module Slot (Nano-Bt-I1 Models Only)

    NANO-BT EPIC SBC Figure 3-13: IPMI LED Connector Location Description ID_LED+ ID_LED- Table 3-12: IPMI LED Connector Pinouts 3.2.12 iRIS Module Slot (NANO-BT-i1 Models Only) CN Label: IPMI1 Half-size PCIe Mini slot CN Type: CN Location: F igure 3-14 The iRIS module slot is used to install the IEI iRIS-1010 IPMI 2.0 module. This slot is only available in NANO-BT-i1 models.

  • Page 44: Lan Led Connectors

    NANO-BT EPIC SBC Figure 3-14: iRIS Module Slot Location 3.2.13 LAN LED Connectors CN Label: JP8, JP9 2-pin header, p=2.0 mm CN Type: CN Location: F igure 3-15 T able 3-13 and Table 3-14 CN Pinouts: The LAN LED connectors are used to connect to the LAN LED indicators on the chassis to indicate users the link activities of the two LAN ports.

  • Page 45: Lvds Connector

    NANO-BT EPIC SBC Description L2_LINK_ACT- Table 3-14: LAN2 LED Connector (JP9) Pinouts 3.2.14 LVDS Connector CN Label: 30-pin crimp, p=1.25 mm CN Type: See Figure 3-16 CN Location: See Table 3-15 CN Pinouts: The LVDS connector is for an LCD panel connected to the board. Figure 3-16: LVDS Connector Location Description Description...

  • Page 46: Memory Card Slot

    NANO-BT EPIC SBC Description Description LVDS_ A_TX3-P LVDS_ A_TX3-N LVDS_B_TX0-P LVDS_ B_TX0-N LVDS_ B_TX1-P LVDS_ B_TX1-N LVDS_ B_TX2-P LVDS_ B_TX2-N LVDS_ B_TXCLK-P LVDS_ B_TXCLK-N LVDS_ B_TX3-P LVDS_ B_TX3-N +LCD VCC +LCD VCC +LCD VCC +LCD VCC Table 3-15: LVDS Connector Pinouts 3.2.15 Memory Card Slot CN Label: DIMM1...

  • Page 47: Microsd Card Slot (E38Xx Models Only)

    NANO-BT EPIC SBC 3.2.16 microSD Card Slot (E38xx Models Only) CN Label: microSD slot CN Type: CN Location: F igure 3-14 The microSD card slot is used to install microSD card. This slot is only available in E38xx models. Figure 3-18: microSD Card Slot Location 3.2.17 PCI-104 Connector CN Label: PC104_PLUS1...

  • Page 48: Figure 3-19: Pci-104 Connector Location

    NANO-BT EPIC SBC Figure 3-19: PCI-104 Connector Location Row A Row B Row C Row D GND/5 V TBD1 AD00 VI/O1 AD02 AD01 +5 V AD05 AD04 AD03 C/BE0# AD07 AD06 AD09 AD08 AD11 VI/O2 AD10 M66EN AD14 AD13 AD12 +3.3 V C/BE1# AD15...

  • Page 49: Pcie Mini Card Slot

    NANO-BT EPIC SBC Row A Row B Row C Row D AD29 +5 V AD28 AD27 +5 V AD30 AD31 REQ0# REQ1# VI/O2 REQ2# +5 V GNT0# GNT1# VI/O3 GNT2# +5 V CLK0 CLK1 CLK2 +5 V CLK3 INTD# +5 V RST# +12 V INTA#...

  • Page 50: Table 3-17: Pcie Mini Card Slot Pinouts

    NANO-BT EPIC SBC Description Description PCIE_WAKE# VCC3 1.5 V VCC3 CLK- CLK+ BUF_PLT_RST# VCC3 BUF_PLT_RST# PCIE_RX4DN_M VCC3 PCIE_RX4DP_M 1.5 V SMBCLK PCIE_TX4DN_CM SMBDATA PCIE_TX4DP_CM USBD3- USBD3+ VCC3 VCC3 RF_LINK# BLUELED# 1.5 V M-SATADET VCC3 Table 3-17: PCIe Mini Card Slot Pinouts Page 38...

  • Page 51: Power Button Connector

    NANO-BT EPIC SBC 3.2.19 Power Button Connector CN Label: PWR_BTN1 2-pin wafer, p=2.0 mm CN Type: See Figure 3-21 CN Location: See Table 3-18 CN Pinouts: The power button connector is connected to a power switch on the system chassis. Figure 3-21: Power Button Location Description PWRBTN_SW#...

  • Page 52: Reset Button Connector

    NANO-BT EPIC SBC Figure 3-22: Power Button Location 3.2.21 Reset Button Connector CN Label: RST_BTN1 2-pin wafer, p=2.0 mm CN Type: See Figure 3-23 CN Location: See Table 3-19 CN Pinouts: The reset button connector is connected to a reset switch on the system chassis. Figure 3-23: Reset Button Connector Location Description PM_SYSRST_R#...

  • Page 53: Sata 3Gb/S Drive Connectors

    NANO-BT EPIC SBC Description Table 3-19: Reset Button Connector Pinouts 3.2.22 SATA 3Gb/s Drive Connectors CN Label: SATA1, SATA2 7-pin SATA drive connectors CN Type: See Figure 3-24 CN Location: See Table 3-20 CN Pinouts: The SATA drive connectors can be connected to SATA drives. Figure 3-24: SATA 3Gb/s Drive Connector Locations Description SATA_TX+...

  • Page 54: Sata Power Connectors

    NANO-BT EPIC SBC 3.2.23 SATA Power Connectors CN Label: SATA_PWR1, SATA_PWR2 2-pin wafer, p=2.0 mm CN Type: See Figure 3-25 CN Location: See Table 3-21 CN Pinouts: Use the SATA Power Connector to connect to SATA device power connections. Figure 3-25: SATA Power Connector Locations Description +5VS Table 3-21: SATA Power Connector Pinouts...

  • Page 55: Serial Port Connector, Rs-422/485

    NANO-BT EPIC SBC Figure 3-26: RS-232 Serial Port Connector Locations PIN NO. DESCRIPTION PIN NO. DESCRIPTION SOUT Table 3-22: RS-232 Serial Port Connector Pinouts 3.2.25 Serial Port Connector, RS-422/485 CN Label: COM4 4-pin wafer, p=2.0 mm CN Type: See Figure 3-27 CN Location: See Table 3-23 CN Pinouts:...

  • Page 56: Smbus Connector

    NANO-BT EPIC SBC Figure 3-27: RS-422/485 Connector Location PIN NO. DESCRIPTION RXD422- RXD422+ TXD422+/TXD485+ TXD422-/TXD485- Table 3-23: RS-422/485 Connector Pinouts Use the optional RS-422/485 cable to connect to a serial device. The pinouts of the D-sub 9 connector are listed below. RS-422 Pinouts RS-485 Pinouts Table 3-24: RS-422/485 Pinouts of D-sub 9 Connector...

  • Page 57: Spi Flash Connector

    NANO-BT EPIC SBC The SMBus (System Management Bus) connector provides low-speed system management communications. Figure 3-28: SMBus Connector Location DESCRIPTION SMB_DATA SMB_CLK +5 V Table 3-25: SMBus Connector Pinouts 3.2.27 SPI Flash Connector CN Label: JSPI1 6-pin wafer, p=1.25 mm CN Type: See Figure 3-29 CN Location:...

  • Page 58: Spi Flash Connector, Ec

    NANO-BT EPIC SBC Figure 3-29: SPI Flash Connector Location PIN NO. DESCRIPTION PIN NO. DESCRIPTION +1.8 VA SPI_CLK_SW SPI_CS SPI_SI_SW SPI_SO_SW Table 3-26: SPI Flash Connector Pinouts 3.2.28 SPI Flash Connector, EC CN Label: JSPI2 6-pin wafer, p=1.25 mm CN Type: See Figure 3-30 CN Location: See Table 3-27...

  • Page 59: Usb 2.0 Connector

    NANO-BT EPIC SBC Figure 3-30: SPI EC Flash Connector Location PIN NO. DESCRIPTION PIN NO. DESCRIPTION +3.3 A SPI_CLK_SW_EC SPI_CS#0_CN_EC SPI_SI_SW_EC SPI_SO_SW_EC Table 3-27: SPI EC Flash Connector Pinouts 3.2.29 USB 2.0 Connector CN Label: USB1 8-pin header , p=2.0 mm CN Type: See Figure 3-31 CN Location:...

  • Page 60: External Peripheral Interface Connector Panel

    NANO-BT EPIC SBC Figure 3-31: USB 2.0 Connector Location PIN NO. DESCRIPTION PIN NO. DESCRIPTION +VCC_USB45 DATA4- DATA5+ DATA4+ DATA5- +VCC_USB45 Table 3-28: USB 2.0 Connector Pinouts 3.3 External Peripheral Interface Connector Panel The figure below shows the external peripheral interface connector (EPIC) panel. The EPIC panel consists of the following: Figure 3-32: External Peripheral Interface Connector Page 48...

  • Page 61: Ethernet Connectors

    NANO-BT EPIC SBC 3.3.1 Ethernet Connectors CN Label: LAN1, LAN2 RJ-45 CN Type: See Figure 3-32 CN Location: See Table 3-29 and Table 3-30 CN Pinouts: A 10/100/1000 Mb/s connection can be made to a Local Area Network. The LAN1 Ethernet connector supports IPMI 2.0.

  • Page 62: Hdmi Connector

    NANO-BT EPIC SBC Figure 3-33: Ethernet Connector Description Description on: linked off: 10 Mb/s blinking: data is being sent/received green: 100 Mb/s orange: 1000 Mb/s Table 3-31: Connector LEDs 3.3.2 HDMI Connector CN Label: CN12 23-pin HDMI port CN Type: See Figure 3-32 CN Location: See Table 3-32...

  • Page 63: Keyboard/Mouse Connector

    NANO-BT EPIC SBC Description Description HDMI_GND HDMI_GND HDMI_GND Table 3-32: HDMI Connector Pinouts Figure 3-34: HDMI Connector 3.3.3 Keyboard/Mouse Connector CN Label: PS/2 CN Type: See Figure 3-32 CN Location: See Table 3-33 CN Pinouts: The keyboard and mouse connector is a standard PS/2 connector. Figure 3-35: PS/2 Pinout and Configuration Description KB DATA...

  • Page 64: Usb 2.0 Connector

    NANO-BT EPIC SBC Description MS CLOCK Table 3-33: Keyboard Connector Pinouts 3.3.4 USB 2.0 Connector CN Label: USB 2.0 port CN Type: See Figure 3-32 CN Location: See Table 3-34 CN Pinouts: The USB connector can be connected to a USB device. Description Description USB3_PWR1...

  • Page 65: Vga Connector

    NANO-BT EPIC SBC Description Description USB3P0_RXDN1 Table 3-35: USB 3.0 Port Pinouts 3.3.6 VGA Connector CN Label: VGA1 15-pin Female CN Type: See Figure 3-32 CN Location: See Table 3-36 and Figure 3-36 CN Pinouts: Both VGA connectors can be connected to monitors that accept standard VGA input for easy dual display setup.

  • Page 66: Installation

    NANO-BT EPIC SBC Chapter Installation Page 54...

  • Page 67: Anti-Static Precautions

    NANO-BT EPIC SBC 4.1 Anti-static Precautions WARNING: Failure to take ESD precautions during the installation of the NANO-BT may result in permanent damage to the NANO-BT and severe injury to the user. Electrostatic discharge (ESD) can cause serious damage to electronic components, including the NANO-BT.
  • Page 68 NANO-BT EPIC SBC WARNING: The installation instructions described in this manual should be carefully followed in order to prevent damage to the components and injury to the user. Before and during the installation please DO the following:  Read the user manual: The user manual provides a complete description of the NANO-BT installation instructions and configuration options.

  • Page 69: So-Dimm Installation

    NANO-BT EPIC SBC 4.2.1 SO-DIMM Installation To install an SO-DIMM, please follow the steps below and refer to Figure 4-1. Figure 4-1: SO-DIMM Installation Locate the SO-DIMM socket on the solder side of the NANO-BT. Place the Step 1: board on an anti-static mat. Align the SO-DIMM with the socket.

  • Page 70: Figure 4-2: Iris-1010 Module Installation

    NANO-BT EPIC SBC Figure 4-2: iRIS-1010 Module Installation Locate the iRIS module slot on the solder side. See Figure 3-14. Step 1: Insert into the socket at an angle. Line up the notch on the RIS-1010 module Step 2: with the notch on the connector. Slide the RIS-1010 module into the socket at an angle of about 20º.

  • Page 71: Pcie Mini Card Installation

    NANO-BT EPIC SBC 4.2.3 PCIe Mini Card Installation To install the PCIe Mini card, please refer to the diagram and instructions below. Figure 4-3: PCIe Mini Card Installation Insert into the socket at an angle. Line up the notch on the card with the notch Step 1: on the connector.

  • Page 72: Clear Cmos Button

    NANO-BT EPIC SBC Figure 4-4: AT/ATX Power Mode Switch Location 4.3.2 Clear CMOS Button To reset the BIOS, remove the on-board battery and press the clear CMOS button for three seconds or more. The clear CMOS button location is shown in Figure 4-5. Figure 4-5: Clear CMOS Button Location Page 60...

  • Page 73: Lvds Panel Resolution Selection

    NANO-BT EPIC SBC 4.3.3 LVDS Panel Resolution Selection Use the SW1 DIP switch to select the resolution of the LCD panel connected to the LVDS connector. SW1 (4-3-2-1) Description 0000 800x600 18-bit (Default) 0001 1024x768 18-bit 0010 1024x768 24-bit 0011 1280x768 18-bit 0100 1280x800 18-bit...

  • Page 74: Lcd Voltage Selection

    NANO-BT EPIC SBC Figure 4-6: LVDS Panel Resolution Selection Switch Location 4.3.4 LCD Voltage Selection The LCD voltage selection switch sets the voltage of the power supplied to the LCD panel. The LCD Voltage Selection settings are shown in Table 4-2. Setting Description +3.3 V (Default)

  • Page 75: Msata/Sata Selection

    NANO-BT EPIC SBC Figure 4-7: LCD Voltage Selection Switch Location 4.3.5 mSATA/SATA Selection Use the J_SATA1 switch to select whether to automatically detect mSATA devices. Setting Description Automatically detect mSATA device (Default) Enable mSATA device Table 4-3: mSATA/SATA Switch Settings Figure 4-8: mSATA/SATA Switch Location Page 63...

  • Page 76: Voltage Selection

    NANO-BT EPIC SBC 4.3.6 PCI-104 Voltage Selection Use the J_PCI104 switch to select the voltage supplied to the PCI-104 expansion module. Setting Description +3.3 V (Default) +5.0 V Table 4-4: PCI-104 Voltage Switch Settings Figure 4-9: PCI-104 Voltage Switch Location 4.3.7 USB Power Select The USB power selection is made through the BIOS option in “Chipset ...

  • Page 77: Internal Peripheral Device Connections

    NANO-BT EPIC SBC 4.4 Internal Peripheral Device Connections This section outlines the installation of peripheral devices to the on-board connectors. 4.4.1 AT Power Connection Follow the instructions below to connect the NANO-BT to an AT power supply. WARNING: Disconnect the power supply power cord from its AC power source to prevent a sudden power surge to the NANO-BT.

  • Page 78: Sata Drive Connection

    NANO-BT EPIC SBC Connect Power Cable to Power Supply. Connect one of the 4-pin (1x4) Molex Step 3: type power cable connectors to an AT power supply. See Figure 4-11. Figure 4-11: Connect Power Cable to Power Supply 4.4.2 SATA Drive Connection The NANO-BT is shipped with two SATA drive cables.

  • Page 79: Single Rs-232 Cable Connection

    NANO-BT EPIC SBC Figure 4-12: SATA Drive Cable Connection Connect the cable to the SATA disk. Connect the connector on the other end Step 3: of the cable to the connector at the back of the SATA drive. See Figure 4-12. To remove the SATA cable from the SATA connector, press the clip on the Step 4: connector at the end of the cable.

  • Page 80: Ipmi Setup Procedure (For Nano-Bt-I1 Models Only)

    NANO-BT EPIC SBC Figure 4-13: Single RS-232 Cable Installation Secure the bracket. The single RS-232 connector has one D-sub 9 male Step 3: connector secured to a bracket. To secure the bracket to the chassis please refer to the reference material that came with the chassis. Step 0: 4.5 IPMI Setup Procedure (for NANO-BT-i1 Models Only) The NANO-BT-i1 features Intelligent Platform Management Interface (IPMI) that helps...

  • Page 81: Bios

    NANO-BT EPIC SBC Chapter BIOS Page 69...

  • Page 82: Introduction

    NANO-BT EPIC SBC 5.1 Introduction The BIOS is programmed onto the BIOS chip. The BIOS setup program allows changes to certain system settings. This chapter outlines the options that can be changed. NOTE: Some of the BIOS options may vary throughout the life cycle of the product and are subject to change without prior notice.

  • Page 83: Getting Help

    NANO-BT EPIC SBC Function Decrease the numeric value or make changes Esc key Main Menu – Quit and not save changes into CMOS Status Page Setup Menu and Option Page Setup Menu -- Exit current page and return to Main Menu F1 key General help, only for Status Page Setup Menu and Option Page Setup Menu...

  • Page 84: Main

    NANO-BT EPIC SBC The following sections completely describe the configuration options found in the menu items at the top of the BIOS screen and listed above. 5.2 Main The Main BIOS menu (BIOS Menu 1) appears when the BIOS Setup program is entered. The Main menu gives an overview of the basic system information.

  • Page 85: Advanced

    NANO-BT EPIC SBC  System Time [xx:xx:xx] Use the System Time option to set the system time. Manually enter the hours, minutes and seconds. 5.3 Advanced Use the Advanced menu (BIOS Menu 2) to configure the CPU and peripheral devices through the following sub-menus: WARNING! Setting the wrong values in the sections below may cause the system...

  • Page 86: Acpi Settings

    NANO-BT EPIC SBC 5.3.1 ACPI Settings The ACPI Settings menu (BIOS Menu 3) configures the Advanced Configuration and Power Interface (ACPI) options. Aptio Setup Utility – Copyright (C) 2013 American Megatrends, Inc. Advanced ACPI Settings Select the highest ACPI sleep state the system ACPI Sleep State [S3 (Suspend to RAM)] will enter when the...

  • Page 87: F81866 Super Io Configuration

    NANO-BT EPIC SBC 5.3.2 F81866 Super IO Configuration Use the F81866 Super IO Configuration menu (BIOS Menu 4) to set or change the configurations for the serial ports. Aptio Setup Utility – Copyright (C) 2013 American Megatrends, Inc. Advanced F81866 Super IO Configuration Set Parameters of Serial Port 1 (COMA) F81866 Super IO Chip...
  • Page 88 NANO-BT EPIC SBC 5.3.2.1.1 Serial Port 1 Configuration  Serial Port [Enabled] Use the Serial Port option to enable or disable the serial port.  Disable the serial port Disabled  Enable the serial port Enabled EFAULT  Change Settings [Auto] Use the Change Settings option to change the serial port IO port address and interrupt address.
  • Page 89 NANO-BT EPIC SBC 5.3.2.1.2 Serial Port 2 Configuration  Serial Port [Enabled] Use the Serial Port option to enable or disable the serial port.  Disable the serial port Disabled  Enable the serial port Enabled EFAULT  Change Settings [Auto] Use the Change Settings option to change the serial port IO port address and interrupt address.
  • Page 90 NANO-BT EPIC SBC 5.3.2.1.3 Serial Port 3 Configuration  Serial Port [Enabled] Use the Serial Port option to enable or disable the serial port.  Disable the serial port Disabled  Enable the serial port Enabled EFAULT  Change Settings [Auto] Use the Change Settings option to change the serial port IO port address and interrupt address.
  • Page 91 NANO-BT EPIC SBC 5.3.2.1.4 Serial Port 4 Configuration  Serial Port [Enabled] Use the Serial Port option to enable or disable the serial port.  Disable the serial port Disabled  Enable the serial port Enabled EFAULT  Change Settings [Auto] Use the Change Settings option to change the serial port IO port address and interrupt address.

  • Page 92: Iwdd H/W Monitor

    NANO-BT EPIC SBC 5.3.3 iWDD H/W Monitor The iWDD H/W Monitor menu (BIOS Menu 6) contains the fan configuration submenus and displays operating temperature, fan speeds and system voltages. Aptio Setup Utility – Copyright (C) 2013 American Megatrends, Inc. Advanced PC Health Status Smart Fan Mode Select :+47 °C...

  • Page 93: Smart Fan Mode Configuration

    NANO-BT EPIC SBC +DDR +5VSB +3.3V +3.3VSB 5.3.3.1 Smart Fan Mode Configuration Use the Smart Fan Mode Configuration submenu (BIOS Menu 7) to configure smart fan temperature and speed settings. Aptio Setup Utility – Copyright (C) 2013 American Megatrends, Inc. Advanced Smart Fan Mode Configuration Smart Fan Mode Select...
  • Page 94 NANO-BT EPIC SBC  SYS_FAN1 Smart Fan Control [Auto Mode] Use the SYS_FAN1 Smart Fan Control option to configure the System Smart Fan.  The fan spins at the speed set in Manual Mode Manual Mode settings.  The fan adjusts its speed using Auto Mode Auto Mode EFAULT settings.

  • Page 95: Rtc Wake Settings

    NANO-BT EPIC SBC 5.3.4 RTC Wake Settings The RTC Wake Settings menu (BIOS Menu 8) configures RTC wake event. The RTC wake function is supported in ACPI (S3/S4/S5) and APM soft off modes. Aptio Setup Utility – Copyright (C) 2013 American Megatrends, Inc. Advanced Wake System with Fixed Time [Disabled]...

  • Page 96: Serial Port Console Redirection

    NANO-BT EPIC SBC  If selected, the following appears with values that Enabled can be selected: *Wake up every day *Wake up date *Wake up hour *Wake up minute *Wake up second After setting the alarm, the computer turns itself on from a suspend state when the alarm goes off.
  • Page 97 NANO-BT EPIC SBC  Console Redirection [Disabled] Use Console Redirection option to enable or disable the console redirection function.  Disabled the console redirection function Disabled EFAULT  Enabled the console redirection function Enabled The following options are available in the Console Redirection Settings submenu when the Console Redirection option is enabled.
  • Page 98 NANO-BT EPIC SBC  Data Bits [8] Use the Data Bits option to specify the number of data bits.  Sets the data bits at 7.  Sets the data bits at 8. EFAULT  Parity [None] Use the Parity option to specify the parity bit that can be sent with the data bits for detecting the transmission errors.

  • Page 99: Iei Feature

    NANO-BT EPIC SBC 5.3.6 IEI Feature Use the IEI Feature menu (BIOS Menu 10) to configure One Key Recovery function. Aptio Setup Utility – Copyright (C) 2013 American Megatrends, Inc. Advanced iEi Feature Auto Recovery Function Reboot and recover Auto Recovery Function [Disabled] system automatically within 10 min, when OS...

  • Page 100: Cpu Configuration

    NANO-BT EPIC SBC 5.3.7 CPU Configuration Use the CPU Configuration BIOS menu (BIOS Menu 11) to view detailed CPU specifications and configure the CPU. Aptio Setup Utility – Copyright (C) 2013 American Megatrends, Inc. Advanced CPU Configuration Number of cores to enable in each processor Intel(R) Atom(TM) CPU E3845 @ 1.91GHz package.
  • Page 101 NANO-BT EPIC SBC  L2 Cache: Lists the amount of storage space on the L2 cache.  L3 Cache: Lists the amount of storage space on the L3 cache.  Intel Virtualization Technology [Enabled] Use the Intel Virtualization Technology option to enable or disable virtualization on the system.

  • Page 102: Ide Configuration

    NANO-BT EPIC SBC 5.3.8 IDE Configuration Use the IDE Configuration menu (BIOS Menu 12) to change and/or set the configuration of the SATA devices installed in the system. Aptio Setup Utility – Copyright (C) 2013 American Megatrends, Inc. Advanced IDE Configuration Enable/Disable Serial Serial-ATA (SATA) [Enabled]...

  • Page 103: Usb Configuration

    NANO-BT EPIC SBC 5.3.9 USB Configuration Use the USB Configuration menu (BIOS Menu 13) to read USB configuration information and configure the USB settings. Aptio Setup Utility – Copyright (C) 2013 American Megatrends, Inc. Advanced USB Configuration Enables Legacy USB support.

  • Page 104: Chipset

    NANO-BT EPIC SBC  Legacy USB support disabled Disabled  Legacy USB support disabled if no USB devices are Auto connected 5.4 Chipset Use the Chipset menu (BIOS Menu 14) to access the North Bridge and South Bridge subsystem configuration menus. WARNING! Setting the wrong values for the Chipset BIOS selections in the Chipset BIOS menu may cause the system to malfunction.

  • Page 105: North Bridge

    NANO-BT EPIC SBC 5.4.1 North Bridge Use the North Bridge menu (BIOS Menu 15) to configure the north bridge parameters. Aptio Setup Utility – Copyright (C) 2013 American Megatrends, Inc. Chipset > Intel IGD Configuration Configure Intel IGD Settings. Memory Information Total Memory 2048 MB (LPDDR3) ---------------------...
  • Page 106 NANO-BT EPIC SBC  Primary Display [Auto] Use the Primary Display option to select the display device used by the system when it boots. Configuration options are listed below.  Auto  EFAULT   DVMT Pre-Allocated [256M] Use the DVMT Pre-Allocated option to specify the amount of system memory that can be used by the internal graphics device.
  • Page 107 NANO-BT EPIC SBC   HDMI  LVDS  On board LVDS [Enabled] Use the On board LVDS option to enable or disable the LVDS connector on the board.  Disable the on-board LVDS connector. Disabled  Enables the on-board LVDS connector. Enabled EFAULT ...

  • Page 108: South Bridge

    NANO-BT EPIC SBC 5.4.2 South Bridge Use the South Bridge menu (BIOS Menu 17) to configure the south bridge parameters. Aptio Setup Utility – Copyright (C) 2013 American Megatrends, Inc. Chipset Auto Power Button Status [Disabled (ATX)] Select AC power state when power is re-applied Restore AC Power Loss [Last State]...

  • Page 109: Pci Express Configuration

    NANO-BT EPIC SBC  The High Definition Audio controller is enabled. Enabled EFAULT  Serial IRQ Mode [Continuous] Use the Serial IRQ Mode option to configure serial IRQ mode for serial interrupts. Configuration options are listed below:  Quiet  Continuous EFAULT ...

  • Page 110: Security

    NANO-BT EPIC SBC  Speed [Auto] Use the Speed option to configure the PCIe Mini card slot (CN8) speed.  Auto EFAULT  Gen 2  Gen 1 5.5 Security Use the Security menu (BIOS Menu 19) to set system and user passwords. Aptio Setup Utility –...

  • Page 111: Boot

    NANO-BT EPIC SBC 5.6 Boot Use the Boot menu (BIOS Menu 20) to configure system boot options. Aptio Setup Utility – Copyright (C) 2013 American Megatrends, Inc. Main Advanced Chipset Security Boot Save & Exit Boot Configuration Select the keyboard Bootup NumLock State [On] NumLock state...
  • Page 112 NANO-BT EPIC SBC  Quiet Boot [Enabled] Use the Quiet Boot BIOS option to select the screen display when the system boots.  Normal POST messages displayed Disabled  OEM Logo displayed instead of POST messages Enabled EFAULT  UEFI Boot [Disabled] Use the UEFI Boot option to enable or disable to boot from a UEFI device.

  • Page 113: Exit

    NANO-BT EPIC SBC 5.7 Exit Use the Exit menu (BIOS Menu 21) to load default BIOS values, optimal failsafe values and to save configuration changes. Aptio Setup Utility – Copyright (C) 2013 American Megatrends, Inc. Main Advanced Chipset Security Boot Save &...
  • Page 114 NANO-BT EPIC SBC  Save as User Defaults Use the Save as User Defaults option to save the changes done so far as user defaults.  Restore User Defaults Use the Restore User Defaults option to restore the user defaults to all the setup options. Page 102...

  • Page 115: Software Drivers

    NANO-BT EPIC SBC Chapter Software Drivers Page 103...

  • Page 116: Software Installation

    NANO-BT EPIC SBC NOTE: The content of the CD may vary throughout the life cycle of the product and is subject to change without prior notice. Visit the IEI website or contact technical support for the latest updates. 6.1 Software Installation All the drivers for the NANO-BT are on the CD that came with the system.

  • Page 117: Figure 6-1: Driver Cd Main Menu

    NANO-BT EPIC SBC Figure 6-1: Driver CD Main Menu A new screen with a list of available drivers appears (Figure 6-2). Step 4: Figure 6-2: Available Drivers Install all of the necessary drivers in the menu. Step 5: Page 105...

  • Page 118: Available Software Drivers

    NANO-BT EPIC SBC 6.2 Available Software Drivers All the drivers for the NANO-BT are on the utility CD that came with the system. The utility CD contains drivers for Windows 7 and Windows 8 operating systems. Please select the corresponding drivers for the system. The following drivers can be installed on the Windows 7 operating system: ...
  • Page 119 NANO-BT EPIC SBC The following drivers can be installed on the Windows 8 operating system:  Bay Trail SOC Chipset Graphics I/O driver  LAN–Intel Audio  Page 107...

  • Page 120: A Regulatory Compliance

    NANO-BT EPIC SBC Appendix Regulatory Compliance Page 108...
  • Page 121 NANO-BT EPIC SBC DECLARATION OF CONFORMITY This equipment is in conformity with the following EU directives: EMC Directive 2004/108/EC  Low-Voltage Directive 2006/95/EC  RoHS II Directive 2011/65/EU  Ecodesign Directive 2009/125/EC  If the user modifies and/or install other devices in the equipment, the CE conformity declaration may no longer apply.
  • Page 122 NANO-BT EPIC SBC Español [Spanish] IEI Integration Corp declara que el equipo cumple con los requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 1999/5/CE. Ελληνική [Greek] IEI Integration Corp ΔΗΛΩΝΕΙ ΟΤΙ ΕΞΟΠΛΙΣΜΟΣ ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ ΤΙΣ ΟΥΣΙΩΔΕΙΣ ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ ΣΧΕΤΙΚΕΣ ΔΙΑΤΑΞΕΙΣ ΤΗΣ ΟΔΗΓΙΑΣ 1999/5/ΕΚ.
  • Page 123 NANO-BT EPIC SBC Româna [Romanian] IEI Integration Corp declară că acest echipament este in conformitate cu cerinţele esenţiale şi cu celelalte prevederi relevante ale Directivei 1999/5/CE. Slovensko [Slovenian] IEI Integration Corp izjavlja, da je ta opreme v skladu z bistvenimi zahtevami in ostalimi relevantnimi določili direktive 1999/5/ES.
  • Page 124 NANO-BT EPIC SBC FCC WARNING This equipment complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: This device may not cause harmful interference, and  This device must accept any interference received, including interference ...

  • Page 125: Bbios Options

    NANO-BT EPIC SBC Appendix BIOS Options Page 113...
  • Page 126 NANO-BT EPIC SBC Below is a list of BIOS configuration options in the BIOS chapter. 　 System Date [xx/xx/xx] ......................72 　 System Time [xx:xx:xx] .......................73 　 ACPI Sleep State [S3 (Suspend to RAM)]................74 　 Serial Port [Enabled]......................76 　 Change Settings [Auto] .......................76 　...
  • Page 127 NANO-BT EPIC SBC 　 DVMT Pre-Allocated [256M] ....................94 　 DVMT Total Gfx Mem [Max]....................94 　 Primary IGFX Boot Display [VBIOS Default] ..............94 　 On board LVDS [Enabled] ....................95 　 Backlight Control Mode [CCFL]..................95 　 Backlight Control Type [PWM] ...................95 　 Backlight Control Voltage Level [3.3V]................95 　...

  • Page 128: C Terminology

    NANO-BT EPIC SBC Appendix Terminology Page 116...
  • Page 129 NANO-BT EPIC SBC Audio Codec 97 (AC’97) refers to a codec standard developed by Intel® AC ’97 in 1997. Advanced Configuration and Power Interface (ACPI) is an OS-directed ACPI configuration, power management, and thermal management interface. Advanced Host Controller Interface (AHCI) is a SATA Host controller AHCI register-level interface.
  • Page 130 NANO-BT EPIC SBC Dual Inline Memory Modules are a type of RAM that offer a 64-bit data DIMM bus and have separate electrical contacts on each side of the module. The digital inputs and digital outputs are general control signals that control the on/off circuit of external devices or TTL devices.
  • Page 131 NANO-BT EPIC SBC Low-voltage differential signaling (LVDS) is a dual-wire, high-speed LVDS differential electrical signaling system commonly used to connect LCD displays to a computer. The Power-on Self Test (POST) is the pre-boot actions the system POST performs when the system is turned-on. Random Access Memory (RAM) is volatile memory that loses data when power is lost.

  • Page 132: D Watchdog Timer

    NANO-BT EPIC SBC Appendix Watchdog Timer Page 120...
  • Page 133 NANO-BT EPIC SBC NOTE: The following discussion applies to DOS environment. Contact IEI support or visit the IEI website for specific drivers for other operating systems. The Watchdog Timer is provided to ensure that standalone systems can always recover from catastrophic conditions that cause the CPU to crash. This condition may have occurred by external EMIs or a software bug.
  • Page 134 NANO-BT EPIC SBC NOTE: When exiting a program it is necessary to disable the Watchdog Timer, otherwise the system resets. EXAMPLE PROGRAM: ; INITIAL TIMER PERIOD COUNTER W_LOOP: AX, 6F02H ;setting the time-out value BL, 30 ;time-out value is 48 seconds ;...

  • Page 135: E Digital I/O Interface

    NANO-BT EPIC SBC Appendix Digital I/O Interface Page 123...

  • Page 136: Introduction

    NANO-BT EPIC SBC E.1 Introduction The DIO connector on the NANO-BT is interfaced to GPIO ports on the Super I/O chipset. The DIO has both 4-bit digital inputs and 4-bit digital outputs. The digital inputs and digital outputs are generally control signals that control the on/off circuit of external devices or TTL devices.

  • Page 137: Assembly Language Sample 1

    NANO-BT EPIC SBC E.2 Assembly Language Sample 1 AX, 6F08H ;setting the digital port as input AL low byte = value AH – 6FH Sub-function: AL – 9 :Set the digital port as OUTPUT :Digital I/O input value E.3 Assembly Language Sample 2 AX, 6F09H ;setting the digital port as output BL, 09H...

  • Page 138: F Hazardous Materials Disclosure

    NANO-BT EPIC SBC Appendix Hazardous Materials Disclosure Page 126...

  • Page 139: Hazardous Materials Disclosure Table For Ipb Products Certified As Rohs Compliant Under 2002/95/Ec Without Mercury

    NANO-BT EPIC SBC F.1 Hazardous Materials Disclosure Table for IPB Products Certified as RoHS Compliant Under 2002/95/EC Without Mercury The details provided in this appendix are to ensure that the product is compliant with the Peoples Republic of China (China) RoHS standards. The table below acknowledges the presences of small quantities of certain materials in the product, and is applicable to China RoHS only.
  • Page 140 NANO-BT EPIC SBC Part Name Toxic or Hazardous Substances and Elements Lead Mercury Cadmium Hexavalent Polybrominated Polybrominated (Pb) (Hg) (Cd) Chromium Biphenyls Diphenyl (CR(VI)) (PBB) Ethers (PBDE) Housing Display Printed Circuit Board Metal Fasteners Cable Assembly Fan Assembly Power Supply Assemblies Battery This toxic or hazardous substance is contained in all of the homogeneous materials for the part is...
  • Page 141 NANO-BT EPIC SBC 此附件旨在确保本产品符合中国 RoHS 标准。以下表格标示此产品中某有毒物质的含量符 合中国 RoHS 标准规定的限量要求。 本产品上会附有”环境友好使用期限”的标签，此期限是估算这些物质”不会有泄漏或突变”的 年限。本产品可能包含有较短的环境友好使用期限的可替换元件，像是电池或灯管，这些元 件将会单独标示出来。 部件名称 有毒有害物质或元素 铅 汞 镉 六价铬 多溴联苯 多溴二苯 醚 (Pb) (Hg) (Cd) (CR(VI)) (PBB) (PBDE) 壳体 显示 印刷电路板 金属螺帽 电缆组装 风扇组装 电力供应组装 电池 O: 表示该有毒有害物质在该部件所有物质材料中的含量均在 SJ/T11363-2006 标准规定的限量要求以下。 X: 表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 SJ/T11363-2006 标准规定的限量要求。 Page 129...

Table of Contents