Download
Share
Print this page
Flashforge FINDER Quick Start Manual
  1. Manuals
  2. Brands
  3. Flashforge Manuals
  4. 3D Printers
  5. Finder
  6. Quick start manual
Flashforge FINDER Quick Start Manual

Flashforge FINDER Quick Start Manual

Hide thumbs Also See for FINDER:

Advertisement

Quick Links

Download this manual See also: User Manual
Quick Start Guide
FINDER
SZ05-EN-A02
1. Hot! Avoid touching the heating nozzle in operation.
WARNING
2. Moving parts in printer may cause injury. Do not wear gloves
or other sources of entanglement in operation.
USERGUIDE
The User Guide is in the USB stick.
This guide is only applicable to FLASHFORGE Finder 3D printer

Advertisement

loading

Related Manuals for Flashforge FINDER

Summary of Contents for Flashforge FINDER

  • Page 1 1. Hot! Avoid touching the heating nozzle in operation. WARNING 2. Moving parts in printer may cause injury. Do not wear gloves or other sources of entanglement in operation. USERGUIDE The User Guide is in the USB stick. This guide is only applicable to FLASHFORGE Finder 3D printer...

  • Page 2: Kit Contents

    Kit Contents Filament Spool 3D Printer Quick Start Guide After-sales Service Card Power Adapter Power Cable USB Cable USB Stick Unclogging Pin Tool Filament Guide Tube Screwdriver Wrench GREASE Allen Wrench Solid Glue PTFE Tube Grease...
  • Page 3 Getting to Know Your Finder 1. Filament Cartridge 2. Filament Outlet 3. Y-Axis Guide Rod 4. X-Axis Guide Rod 6. Spring Presser 5. Filament Inlet 7. Touch Screen 8. Build Plate 9. Leveling Knob 11. USB Cable Input 12. USB Stick Input 10.
  • Page 4 2. Remove the side protective foam sheets, lift your Finder out of the box. you will see the Finder in a transparent bag. 3. Remove the tape and then remove the bag. 5. The foam sheet on top of the printer should...
  • Page 5 7. Use scissors to cut the four buckles 8. Take the protective foam for filament that hold the rods in place. out of the Finder. You will see a spool of PLA filament inside. 9. Lift the build plate up with care.

  • Page 6: Hardware Assembly

    5. Connect power adapter with the power cable and then insert the power supply into the power input on the back of the finder. Turn on the power switch and press the touch screen button to turn on the printer.
  • Page 7 [OK] button. 1. Tap [Tools] - [Level] on your Finder touch screen. Please wait while the extruder and platform finish initial movements. Screw three knobs under the platform anticlockwise until you can’t...
  • Page 8 Confirm Are you sure you can’t Verifying the distance between nozzle tighten these three nuts any and plate... more? Wait 2. Tap [Yes] if you can't tighten all the nuts any more, or tap [No] to continue tightening. After selecting [Yes], the extruder will move towards the first point and the plate will move up and down to verify the distance between nozzle and plate.

  • Page 9: Loading / Changing Filament

    Loading / Changing Filament HOME Filament Level Home Manual Build Preheat Tools Setting Status About 1. Tap [Tools] and then tap [Filament] and [Load] to load filament. I’m heating up... 100% 220℃ / 220℃ Extruder Load Unload Cancel 2. The extruder will automatically heat up. Once heated, filament will be drawn through the extruder.
  • Page 10 First Print Build Preheat Tools 1. Please insert the USB stick into Finder. In the print interface, tap [Build]-[USB Stick]. Finder Quick Start Guide 快 Instructional Video 教学视频 速启动指南 Test Files 测试文件 Finder Use Guide 说明书 Flashprint software 切片软 件...
  • Page 11 Scan QR to Get More After-Sales Support After-Sales Service: support@ff3dp.com Amazon.com orders only: 597891915@qq.com Tel: +86 579 82273989 Web: www.flashforge.com Add: 2/F, No.518, Xianyuan Road, Jinhua, Zhejiang, China...