Key Digital KD-IP922ENC Operating Instructions Manual page 15
Enterprise av over ip encoder
Hide thumbs
Also See for KD-IP922ENC:
- Operating instructions manual (42 pages) ,
- Manual (119 pages) ,
- Manual (88 pages)
Table of Contents
Advertisement
26
-- IP922DEC Audio Setup Command ( xxxx=[0~1024,A] A=All )
-- SPD xxxx AV yy : Set Output xxxx Audio Volume to yy=[00-99],U,D
-- SPD xxxx AB yy : Set Output xxxx Audio Balance to yy=[00-40],U,D
-- SPD xxxx AL yy : Set Output xxxx Audio Bass to yy=[00-24],U,D
-- SPD xxxx AM yy : Set Output xxxx Audio Middle to yy=[00-24],U,D
-- SPD xxxx AH yy : Set Output xxxx Audio Treble to yy=[00-24],U,D
-- SPD xxxx AD yy : Set Output xxxx Audio Delay to yy=[00-99],U,D
-- SPD xxxx A E/D : Set Output xxxx Audio Mute Enabled/Disabled/Toggle --
--
-- IP922DEC Video Setup Command ( xx/xxx/xxxx=[0000~1024,A] A=All )
-- SPD xxxx VS y
: Set Output xxxx Video Source to y [1=IP, 2=Local]
--
-- Network Setup Command
( xxx=[000-255], zzzz=[0001~9999], y=[1~3] ) --
-- SPCETIPA xxx.xxx.xxx.xxx : Set Host IP Address to xxx.xxx.xxx.xxx
-- SPCETIPM xxx.xxx.xxx.xxx : Set Net Mask to xxx.xxx.xxx.xxx
-- SPCETIPR xxx.xxx.xxx.xxx : Set Route IP Address to xxx.xxx.xxx.xxx
-- SPCETIPP zzzz
: Set TCP/IP Port to zzzz
-- SPCETDCP E/D
: Set DHCP E=Enable/D=Disable
-- SPCETIPB
: Apply New Network Config
-- SPCETLN1 y
: Set LAN Port1 by y [1=1G-BaseT, 2=100BaseT, 3=Auto]
-- SPCETLN2 y
: Set LAN Port2 by y [1=1G-BaseT, 2=100BaseT, 3=Auto]
--
-- Control I/O Port Setup Command ( x=[0~3], y=[0~9], z=[0001-9999] )
-- SPB x CM y
: Set Control Mode of I/O Port x=[1~3] by y
--
[1=IP922 Control, 2=Compass Control, 3=Open API, 4=Control Ext.]
-- SPB x PC y
: Set Port Configuration of I/O Port x=[1~3] by y
[0=None, 1=IR IN, 2=IR OUT, 3=RS232, 4=TRIGGER IN, 5=TRGGER OUT] --
-- SPB 1 IRS y
: Set IR Source by y [1=IR Sensor, 2=Serial IR ]
-- SPB x RSB y
: Set RS232 Baud Rate of I/O Port x=[2~3] by y bps
--
[0=115200, 1=57600, 2=38400, 3=19200, 4=9600, 5=4800]--
-- SPB x RSL y
: Set RS232 Data Length of I/O Port x=[2~3] by y=[7~8] --
-- SPB x RSP y
: Set RS232 Parity Bit of I/O Port x=[2~3] by y=[0~2]
[0=None, 1=Odd, 2=Even]
-- SPB x RSS y
: Set RS232 Stop Bit of I/O Port x=[2~3] by y=[0~2]
-- SPB x OSL y
: Set Output Level of I/O Port x by y [1=MIN ~ 7=MAX]
-- SPB x TCP zzzz : Set TCP Port of I/O Port x[0=I/O Port Cfg.] by zzzz--
-- SPB x IGD zzz
: Set IR IN/RS232 RxD Group ID of I/O Port x by zzz
-- SPB x OGD zzz
: Set IR OUT/RS232 TxD Group ID of I/O Port x by zzz --
--
-- System Control Setup Command ( xx=[0000-1024], y=[1~4], z=[0-4] )
-- SPC DN cccccccccccccccc
: Set Device Name
-- SPC SID xxxx : Set System ID xxxx for Multicast,[0000=Unicast]
-- SPCFB E/D
: Set Panel Button E/D (E=Enable,D=Disable) at IP922DEC--
-- SPCDF
: Reset to Factory Default All
-------------------------------------------------------------------------
--
Status command (STA) returns current state and settings of the unit:
--
-------------------------------------------------------------------------
--
--
--
-------------------------------------------------------------------------
--
--
KD-IP922ENC
--
--
--
-- Device Name = IP922ENC0001
-- Power = ON,
Fanel Button = Enable,
--
--
--
-- Network Setting Status
--
-- MAC Address = 60:89:B1:90:00:01
--
-- Host IP Address = 192.168.001.100
-- Net Mask = 255.255.000.000
--
-- Router IP Address = 192.168.001.001
--
-- TCP Port = 0023,
--
-- LAN1 = AUTO, LAN2 = AUTO
--
--
--
-- Control I/O Ports Status
--
-- Main : TCP = 4580
--
-- I/O1: CM=IP922
--
--
TCP=4581, IGD=0001, OGD = 0002
--
-- I/O2: CM=IP922
--
--
TCP=4582, IGD=0003, OGD=0004
--
-- I/O3: CM=IP922
--
--
TCP=4583, IGD=0005, OGD=0006
--
--
-- IP922ENC Video/Audio Status
--
-- 0001: DN=IP922ENC0001
--
--
IP=192.168.001.101 , VA=HDMI , HPD=ON ,HCP=ON , AUD=2CH PCM
--
AS=HDMI, AV=99, AB=20, AL=12, AM=12, AH=12, AD=00, MUTE=OFF
-- 0002: DN=IP922ENC0002
--
--
IP=192.168.001.102 , VA=HDMI , HPD=ON ,HCP=ON , AUD=2CH PCM
--
--
AS=HDMI, AV=99, AB=20, AL=12, AM=12, AH=12, AD=00, MUTE=OFF
--
-- 0003: DN=IP922ENC0003
--
--
IP=192.168.001.103 , VA=HDMI , HPD=ON ,HCP=ON , AUD=2CH PCM
--
AS=HDMI, AV=99, AB=20, AL=12, AM=12, AH=12, AD=00, MUTE=OFF
--
-- 0004: DN=IP922ENC0004
--
IP=192.168.001.104 , VA=HDMI , HPD=ON ,HCP=ON , AUD=2CH PCM
--
--
AS=HDMI, AV=99, AB=20, AL=12, AM=12, AH=12, AD=00, MUTE=OFF
--
--
--
-- IP922DEC Video/Audio/Video Wall Status
--
-- 0001: DN=IP922DEC0001
--
IP=192.168.002.101, IN=0001, OUT=ON
--
--
AV=99, AB=20, AL=12, AM=12, AH=12, AD=00, MUTE=OFF
--
VW=OFF, VID=00, MWH=01, MWV=01, MWP=001, SWH=01, SWV=01
--
SWP=001, BWL=0001, BHL=0001, SWL=0001, SHL=0001, MSL=000
--
MSR=000, MSU=000, MSD=000, SUH=0000, SUV=0000, SRR=0
Key Digital Systems STATUS
F/W Version : BV1.00, MV1.00, AV1.00
, System ID = 0001
Forced HPD = OFF
DHCP = Disable,
Link = ON
, CFG=IR IN
,OSL=7, RS=57600-8-0-1 , IRS=1
, CFG=NONE
,OSL=7, RS=57600-8-0-1 , IRS=2
, CFG=RS232
,OSL=7, RS=57600-8-0-1 , IRS=2
, MAC=60:89:B1:90:00:01, GID=0001, LINK=ON --
, MAC=60:89:B1:90:00:01, GID=0002, LINK=ON --
, MAC=60:89:B1:90:00:01, GID=0003, LINK=ON --
, MAC=60:89:B1:90:00:01, GID=0004, LINK=ON --
, MAC=60:89:B1:92:00:01, GID=0001, LINK=ON --
, HPD=ON ,HCP=ON , DG=ON --
27
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
Advertisement
Table of Contents
