Save the carton and all packing materials. In the event that a fixture must be returned to the factory, it is important that the fixture be returned in the original factory box and packing. Your shipment includes: Showtec Cameleon Flood 15 Q4 1x Schuko to 3-pins (IP-65 ) Power cable 1,5m ...
Page 4
• If your Showtec device fails to work properly, discontinue the use immediately. Pack the unit securely (preferably in the original packing material), and return it to your Showtec dealer for service.
Cameleon Flood 15 Q4 • The user is responsible for correct positioning and operating of the Cameleon Flood 15 Q4. The manufacturer will not accept liability for damages caused by the misuse or incorrect installation of this device. • This device falls under protection class I. Therefore it is essential to connect the yellow/green conductor to earth.
Cameleon Flood 15 Q4 The Cameleon Flood 15 Q4 can be placed on a flat stage floor or mounted to any kind of truss with a clamp. Improper installation can cause serious injuries and/or damage of property! Connection with the mains Connect the device to the mains with the power-plug.
Cameleon Flood 15 Q4 Return Procedure Returned merchandise must be sent prepaid and in the original packing, call tags will not be issued. Package must be clearly labeled with a Return Authorization Number (RMA number). Products returned without an RMA number will be refused. Highlite will not accept the returned goods or any responsibility.
Cameleon Flood 15 Q4 Description of the device Features The Cameleon Flood 15 Q4 is a wall washer with great output and effects. It is an extension on our Cameleon series. It's an indoor and outdoor solution for illumination of numerous objects. ...
Cameleon Flood 15 Q4 Overview Fig. 01 01) 15x 5W 4-in-1 RGBW ProLight Opto Hornet Series 02) Mounting bracket Backside Fig. 02 03) Special mini 3-pin DMX cable IN IP-65 04) Special mini 3-pin DMX cable OUT IP-65 05) Special mini 3-pin power cable IN IP-65...
Cameleon Flood 15 Q4 Installation Remove all packing materials from the Cameleon Flood 15 Q4. Check if all foam and plastic padding is removed. Connect all cables. Do not supply power before the whole system is set up and connected properly.
Cameleon Flood 15 Q4 Multiple Cameleon Floods (Master/Slave control) 01) Fasten the effect light onto firm trussing. Leave at least 0,5 meter on all sides for air circulation. 02) Always use a safety cable (ordercode 70140 / 70141). 03) Use a 3-p XLR cable to connect the Cameleon Floods and other devices.
Cameleon Flood 15 Q4 Multiple Cameleon Floods (DMX Control) 01) Fasten the effect light onto firm trussing. Leave at least 0,5 meter on all sides for air circulation. 02) Always use a safety cable (ordercode 70140 / 70141). 03) Use a 3-pin XLR cable to connect the Cameleon Floods and other devices.
Cameleon Flood 15 Q4 Fixture Linking You will need a serial data link to run light shows of one or more fixtures using a DMX-512 controller or to run synchronized shows of two or more fixtures set to a master/slave operating mode. The combined number of channels required by all the fixtures on a serial data link determines the number of fixtures the data link can support.
Cameleon Flood 15 Q4 Control Panel A) O-LED Display MODE button C) SET button D) UP button DOWN button Fig. 05 Control Mode The fixtures are individually addressed on a data-link and connected to the controller. The fixtures respond to the DMX signal from the controller. (When you select the DMX address and save it, the controller will display the saved DMX address, next time.)
Cameleon Flood 15 Q4 Main Menu Options 01) Upon start-up, the display will show one screen: 02) Press the SET or MODE button to open the main menu. The display will show: 03) Press the UP/DOWN buttons to toggle between the menus.
Cameleon Flood 15 Q4 3. DMX Address/ DMX Configuration With this menu you can set the device’s DMX starting address and choose a DMX channel mode. 01) While in the main menu, press the UP/DOWN buttons to choose DMX. 02) Press the SET button to open the menu.
Cameleon Flood 15 Q4 6. Settings With this menu you can set the device’s settings. 01) While in the main menu, press the UP/DOWN buttons to choose Settings. 02) Press the SET button to open the menu. 03) Press the UP/DOWN buttons to toggle between the following menus: Curves Select, Dimmer Speed, Dmx Fail, Dmx Sync, Lock, Factory.
Cameleon Flood 15 Q4 6.3. Dmx Fail With this menu, you can adjust the behaviour of the device in case of a DMX signal error . 01) While in Settings menu, press the UP/DOWN buttons to choose Dmx Fail. 02) Press the SET button to open the menu.
Cameleon Flood 15 Q4 DMX Channels 4 DMX Channels Channel 1 – Red Dimmer intensity 0-255 Gradual adjustment Red from 0-100% Channel 2 – Green Dimmer intensity 0-255 Gradual adjustment Green from 0-100% Channel 3 – Blue Dimmer intensity 0-255 Gradual adjustment Blue from 0-100% Channel 4 –...
Page 21
Cameleon Flood 15 Q4 Channel 4 – Color presets (CH1 must be set between 1-255 No function 8-13 Color 1 (R255, G000, B000, W000) 14-20 Color 2 (R255, G000, B000, W100) 21-27 Color 3 (R255, G000, B000, W200) 28-34 Color 4 (R255, G050, B000, W000)
04) The electric power supply cables must not show any damages or material fatigue. The Cameleon Flood 15 Q4 requires almost no maintenance. However, you should keep the unit clean. Otherwise, the fixture’s light-output will be significantly reduced. Disconnect the mains power supply, and then wipe the cover with a damp cloth.
Cameleon Flood 15 Q4 No Response to DMX Suspect the DMX cable or connectors, a controller malfunction, a light effect DMX card malfunction. 01) Check the DMX setting. Make sure that DMX addresses are correct. 02) Check the DMX cable: Unplug the unit; change the DMX cable; then reconnect to electrical power.