Table of Contents
Advertisement
locations have been shown to have a detrimental effect
on signal strength.
A fair amount of care may be required to mount the ra-
dio so as to achieve an optimal RF path. The installer
should spend as much time as needed to obtain the
highest signal level possible.
For Commercial Burglary installations, install in accord-
ance with UL 681, Standard for Installation and Classifi-
cation of Burglary and Holdup Alarm Systems. Installa-
tion shall also be in accordance with UL 827, Standard
for Central-Station Alarm Services, and UL 1641, Stand-
ard for Installation and Classification of Residential Bur-
glar Alarm Systems.
a. Before applying power, be sure to connect the
antenna. Temporarily connect power to the radio
from a fully charged 12V (4AH minimum) battery.
DO NOT mount the StarLink radio at this time.
b. Position the unit in the desired mounting location,
with antenna oriented vertically. The signal strength
is displayed by the Green "Signal Strength LED" la-
beled "D3" (located at the lower right corner of the
PC board). The GSM radio tower signal strength
may fluctuate from day to day, therefore it is best to
try to find a mounting location where the LED pro-
vides a minimum of 4 blinks.
c. Once a location has been selected based on signal
coverage, permanently secure the unit using #8
screws (not supplied) in the two mounting holes.
WARNING: To ensure user safety and to satisfy FCC
RF exposure requirements, this unit must be installed so
that a minimum separation distance of 60cm (24") is al-
ways maintained between the antenna of the transmitting
device and nearby persons. Use ONLY the existing an-
tenna supplied by radio to comply with this warning
(Exception: The SLE-ANTEXT extended antenna with
15 feet of cable).
STEP 3: WIRING (PRIMARY AND BACKUP MODES)
22-gauge wire may be used if mounted up to 50 feet from
the control panel, and 18-gauge wire should be used for up
to 100 feet. Reference the wiring diagrams further in this
manual. See the section CONTROL PANEL PROGRAM-
MING further in this manual.
NOC Originated
Alarms
Supervisory Fail
Press to Send
Test Signal
Press to Send
Radio Test
™
StarLink
SLE Commercial Series Alarm Communicators -- Installation Instructions
S I G N A L S O R I G I N AT E D A T T H E N O C
Contact ID
Pulse Format
Event Data
Event Code
Sent
Sent
E356 A00 Zn000
99
E601 A00 Zn000
98
Not Applicable
Nothing sent to
Not Applicable
CS receiver
STARLINK RADIO RELATED EVENT
REPORT CODES
EVENT
IN 1 Fire
IN 2 Panic
IN 3 Trouble
Low Battery/Voltage
Tamper Trouble
Line Cut
Reboot
IN 1 CO (Carbon Monoxide)
Panic Alarm*
Holdup Alarm*
Medical Alarm*
24 hour Aux. Alarm*
24 hour Aux. Restore*
Burg Perimeter Alarm*
Burg Interior Alarm*
Keypad Holdup Alarm (ambush)*
Keypad Panic Alarm*
Keypad Emergency Alarm*
Opening*
Closing*
A.C. Trouble*
Tel 1 Fail*
*Not generated by the StarLink radio.
**See table "NOTICE TO AUTHORITIES HAVING JURISDICTION..." on page 2.
Cover Tamper
The SLE series radios in the plastic housings are provided
with a front tamper switch. Note: The tamper switch on
the radio PC board is always functional and requires no
programming.
Initiated By
Automatically by NOC if fail to receive
any signal from StarLink radio within
Supervisory Timeout duration.
Manually by dealer from the Manage-
ment Center Signal Log screen
(located at www.napconoc.com).
Sends test into CS receiver.
Manually by dealer from the Manage-
ment Center Checkins screen (located
at www.napconoc.com). Sends a com-
mand to the StarLink radio to force a
check-in to the NOC.
(Contact ID by default)
CONTACT ID
AREA
CODE
ZONE #
0
E110
990
0
E120
992
0
E300
993
0
E302
994
0
E341
995
0
E352
996
0
E625
997
0
E162
998
E123
E122
E100
E150
R150
E131
E132
E121
E123
E140
E401
R401
E301
E351
Comments
For Auto Enroll, uses captured telephone
number, Sub ID and format. For Dealer
Programmed, uses entered telephone
number, Sub ID and format.
Same comment as above.
----
PULSE
4/2**
1A
22
F3
F4
F5
F6
F7
18
5
Hide quick links:
Advertisement
Table of Contents
