Denon DN-X100 Service Manual page 9

Pin
Pin Name Symbol
No.
33 D14 D6
34 D15 D7
35 Vcc Vcc
36 A0 A0
37 A1 A1
38 A2 A2
39 A3 A3
40 A4 A4
41 A5 A5
42 A6 A6
43 A7 A7
44 Vss Vss
45 A8 A8
46 A9 A9
47 A10 A10
48 A11 A11
49 A12 A12
50 A13 A13
51 A14 A14
52 A15 A15
53 A16 A16
54 A17 A17
55 P52 _FX1ON
56 P53 _FX2ON
57 Vss Vss
58 P60 LEDFX1
59 P61 LEDFX2
60 P62 FX1SW
61 P67 P67
62 _STBY _STBY
63 _RES _RES
64 NMI NMI
65 Vss Vss
66 EXTAL EXTAL
67 XTAL XTAL
68 Vcc Vcc
69 _AS _AS
70 _RD _RD
71 _HWR _HWR
72 P66 JDET
73 MD0 MD0
74 MD1 MD1
75 MD2 MD2
76 Avcc Avcc
77 Vref Vref
78 P70,AN0 CH1FADER
79 P71,AN1 CFFADER
80 P72,AN2 CH2FADER
81 P73,AN3 CH1CUREV
82 P74,AN4 CFCUREV
83 P75,AN5 CH2CUREV
84 P76,AN6 AN6
85 P77,AN7 AN7
86 Avss Avss
87 P80 P80
I/O Det Int Pu Ext Res
D/I - - - -
D/I - - - -
- - - - -
A/O - - - -
A/O - - - -
A/O - - - -
A/O - - - -
A/O - - - -
A/O - - - -
A/O - - - -
A/O - - - -
- - - - -
A/O - - - -
A/O - - - -
A/O - - - -
A/O - - - -
A/O - - - -
A/O - - - -
A/O - - - -
A/O - - - -
A/O - - - -
A/O - - - -
O - ON - L
O - ON - L
- - - - -
O - - Pu L
O - - Pu L
I - - - L
I - - - H
- - - - -
- - - - -
I - - Pu -
- - - - -
- - - - -
- - - - -
- - - - -
- - - - -
O - - - -
- - - - -
I - - - L
I - - - -
I - - - -
I - - - -
- - - - -
- - - - -
I - - - -
I - - - -
I - - - -
I - - - -
I - - - -
I - - - -
I - - - -
I - - - -
- - - - -
O - - Pu L
Ini
- Data bus
- Data bus
- Power supply(+5V)
- Address bus
- Address bus
- Address bus
- Address bus
- Address bus
- Address bus
- Address bus
- Address bus
- GND(0V)
- Address bus
- Address bus
- Address bus
- Address bus
- Address bus
- Address bus
- Address bus
- Address bus
- Address bus
- Address bus
H PGM1 EFFECT LOOP enabler 'L' : enabler (DN-X300 only)
H PGM2 EFFECT LOOP enabler 'L' : enabler (DN-X300 only)
- GND(0V)
H PGM1 EFFECT LOOP LED control.
H PGM2 EFFECT LOOP LED control.
H PGM1 EFFECT LOOP ON/OFF SW 'L' : ON (DN-X300 only)
H DN-X100/300 program selected Pin 'L' : DN-X300
H When driven low,this pin forces a transition to hardware standby mode.
- Reset signal 'L' : Reset
H Not used
- GND(0V)
- OSC 16MHz
- OSC 16MHz
- Power supply(+5V)
- Not used
- Goes low to indicate reading from the external address space
- Not used
H Check Send Return jack inserted
- IC Operating mode control
- IC Operating mode control
- IC Operating mode control
- Power supply pin for the A/D converters(+5V).
- Reference voltage input pin for the A/D converters(+5V).
Hi-z CH1 FADER VR A/D converter
Hi-z CROSS FADER VR A/D converter
Hi-z CH2 FADER VR A/D converter
Hi-z CH1 FADER CONTOUR VR A/D converter
Hi-z CROSS FADER CONTOUR VR A/D converter
Hi-z CH2 FADER CONTOUR VR A/D converter
Hi-z Not used
Hi-z Not used
- Ground pin for A/D converters(0V).
L Not used
8
DN-X100
Function
(DN-X300 only)
(DN-X300 only)