Cisco TelePresence ISDN Link Reference Manual page 18

Cisco TelePresence ISDN Link
Contents Introduction
systemtools rootsettings serial [password]
Command to control the root user availability. Enable access to
the system for the root user on the serial port.
password: The root user password.
systemtools rootsettings off
Command to control the root user availability.
Disable access to the system for the root user on all ports.
systemtools rootsettings never
Command to control the root user availability.
NOTE! The root user is permanently turned off!
To get back the root user the system must be reset to factory
defaults, ref. xCommand SystemUnit FactoryReset.
systemtools securitysettings jitc
Set up security requirements so they meet JITC.
Set or view password and PIN polices enforced on the unit.
systemtools securitysettings isjitc
Check if the current settings are JTIC compliant.
systemtools securitysettings default
Revert to default security settings.
systemtools securitysettings ask
Query for the separate configurations. When issuing this
command you will see each policy separately.
•
Press enter to keep the current value.
•
Enter a number and press enter to change the given policy.
•
The default value "0" indicates no restrictions.
Max failed login attempts [0]?
•
Number of failed log ins until a user is set inactive.
D14953.01 ISDN Link API Reference Guide IL1.0 June 2012.
© 2012 Cisco Systems, Inc. All rights reserved.
About the API About the API xConfiguration
Suspend-time after max failed login attempts (minutes) [0]?
•
Number of minutes the user is set inactive after maximum
failed login attempts have been exceeded.
Max simultaneous sessions total [0]?
•
Maximum number of users that can be logged in
simultaneous to web and maximum number of users that
can be logged in simultaneous to ssh.
Max simultaneous sessions per user [0]?
•
Maximum number of simultaneous sessions per user.
Number of passwords to remember [0]?
•
Number of previous passwords that the new password must
differ from.
Number of PINs to remember [0]?
•
Number of previous PINs that the new PIN must differ from.
Maximum time between password renewals (days) [0]?
•
If the user has not changed the password within the
renewal time the user will be set inactive.
Minimum time between password renewals (hours) [0]?
•
The user can only change password once within this limit.
Maximum time between PIN renewals (days) [0]?
•
If the user has not changed the PIN within the renewal time
the user will be set inactive.
Minimum time between PIN renewals (hours) [0]?
•
The user can only change PIN once within this limit.
Maximum time between log ins (days) [0]?
•
If the user has not logged in within this limit the user will be
set inactive.
Max consecutive equal digits in PINs [0]?
•
Maximum consecutive equal digits in PINs.
Minimum number of digits in PINs [0]?
•
Minimum number of digits in PINs.
Maximum number of digits in PINs [0]?
•
Maximum number of digits in PINs.
18
xCommand xStatus
Max consecutive identical characters in passwords [0]?
•
Maximum consecutive identical characters in passwords.
Minimum number of characters in passwords [0]?
•
Minimum number of characters in passwords.
Maximum number of characters in passwords [0]?
•
Maximum number of characters in passwords.
Minimum number of lower-case letters in passwords [0]?
•
Minimum number of lower-case letters in passwords.
Minimum number of upper-case letters in passwords [0]?
•
Minimum number of upper-case letters in passwords.
Minimum number of numerical characters in passwords [0]?
•
Minimum number of numerical characters in passwords.
Minimum number of special characters in passwords [0]?
•
Minimum number of special characters in passwords.
Minimum number of character groups in passwords [0]?
•
Minimum number of character groups in passwords.
Minimum number of character changed from previous
password [0]?
•
Minimum number of character changed from previous
password.
systemtools securitystatus
Shows the security status for the ISDN Link.
systemtools showlog [n]
List available logs.
n: select archived log number 'n', where n=1 is the most
recent.
systemtools showlog logname|all [n]
Show specific log or all logs.
logname/all: Specify the name of the log or select all.
n: select archived log number 'n', where n=1 is the most
recent.
API Reference Guide
Contact us
www.cisco.com