Safety Notices 1. Please use the specified power adapter. If you need to use the power adapter provided by other manufacturers under special circumstances, please make sure that the voltage and current provided is in accordance with the requirements of this product, meanwhile, please use the safety certificated products, otherwise may cause fire or get an electric shock.
Table of Content 1. INTRODUCING DPH-150S/DPH-150SE VOIP PHONE ............7 DPH-150S/DPH-150SE ..........7 1.1 T HANK YOU FOR YOUR PURCHASING ......................7 1.2 D ELIVERY ONTENT ..........................7 1.3 K EYPAD ..................... 9 1.4 P ORT FOR CONNECTING ......................9 1.5 I...
4.5.3 Voice Message ......................18 ..........................18 4.7 P ................18 4.8 P ROGRAMMABLE ONFIGURATION 5. OTHER FUNCTIONS ......................21 ......................21 5.1 A ANDDOWN ....................21 5.2 B NONYMOUS ........................21 5.3 D ........................21 5.4 D ........................22 5.5 A EDIAL ......................
1. Introducing DPH-150S/DPH-150SE VoIP Phone 1.1 Thank you for your purchasing DPH-150S/DPH-150SE Thank you for your purchasing DPH-150S/DPH-150SE. DPH-150S/DPH-150SE is a full-feature telephone that provides voice communication over the same data network that your computer uses. This phone’s functions not only much like a traditional phone, allowing to place and receive calls, and enjoy other features that traditional phone has, but it also own many data services features which you could not expect from a traditional telephone.
Key name Function Description Navigation key assist users for operating. In desktop, dialer, calling, desktop long pressed state they have Navigation special function. You can configure through the web page according to your patterns of use. Temporarily hold the active call during the talking; press the key again to unhold the call.
and so on. DSS keys You can configure them in the web page. 1.4 Port for connecting Port Port name Description Power switch Input: 5V DC, 0.6A 10/100M Connect it to Network 10/100M Connect it to PC External console Port type: RJ-11 direct connector interface Headset Port type: RJ-9 connector...
Call out Call in Call hold Auto answer Call mute Contact DND (Do not Disturb) In hand-free mode In headset mode In headset mode Missed call Call forward 1.6 LED introduction Table 1 Programmable key LEDs for BLF LED Status Description Steady green The object is in idle status.
LED Status Description Steady green The account is active. Fast blinking red There is an incoming call to the account. Slow blinking red The call is on hold. Slow blinking red Registration is unsuccessful. The line is not unapplied or idle. Table 4 Programmable key LEDs for MWI LED Status Description...
Make sure that the power you use is comply with the parameters of power adaptor. 1. Plug power adaptor to power socket. 2. Plug power adaptor’s DC output to the DC5V port of DPH-150S/DPH-150SE to start up. 3. There will be displayed blue line and “Dlink” Logo on the screen. After finishing startup, phone will show greeting, current date and time and so forth.
DPH-150S/DPH-150SE uses DHCP to get WAN IP configurations, so phone could access to network as long as there is DHCP server in it. If there is no DHCP server available, phone has to be changed WAN network setting to Static IP or PPPoE.
2. Press back six times to return to the idle screen. 3. Check the status, the screen shows “DHCP”, if the screen shows the IP address and gateways which were set just now, it shows that DHCP mode takes effect. 3 Basic Function 3.1 Making a call 3.1.1 Call Device...
3.3 DND Press DND softkey to active DND Mode. Further incoming calls will be rejected and the display shows: icon. Press DND softkey twice to deactivate DND mode. You can find the incoming call record in the Call History. 3.4 Call Forward This feature allows you to forward an incoming call to another phone number.
normal conversation. 3.8 Call transfer 1. Blind Transfer During talk, press the key Transf, and then dial the number that you want to transfer to, and finished by "#". Phone will transfer the current call to the third party. After finishing transfer, the call you talk to will be hanged up.
4 Advanced Function 4.1 Redial / Unredial If B is in busy line when A calls B, A will get notice: busy, please hang up. If A want to connect B as soon as B is in idle, he can use redial function at the moment and he can dials an appointed prefix number plus B’s number to realize redial function.
Inbox/Outbox. 3) After view the new message, you can press Reply to reply the message, and use the 2aB softkey to change the Input Method, when enter the reply message, press OK, then use the navigation keys to select the line from which you want to send, then Send. 4) If you want to write a message, you can press New and enter message.
description for each function. The default configuration for each key is N/A which means the key hasn’t been set for any functions. 1. Set the type as Memory Key Press Menu->Settings->Basic Settings->Enter->Keyboard->DSS Key Settings, you have two options: Line Key Settings and Function Key Settings, choose one you want to make the assignment, use the navigation key to choose the type as memory key.
Hold Transfer Phonebook Redial Pickup Join Call Forward History Flash Memo Headset Release: Pressing the key, you can end the call. Lock: Pressing the key, you can lock the keyboard. ...
state of an object changes, the corresponding LED will change. 5. Other Functions 5.1 Auto Handdown 1. Press Menu ->Features-> Enter->Auto Handdown-> Enter. 2. Set the Mode Enable through the navigation key, then set Time, unit is minute, then press Save.
5.5 Auto Redial 1. Press Menu ->Features-> Enter->Auto Redial-> Enter. 2. Choose Mode Enabled or Disabled through the navigation key. If you choose Enable, you also need to set Interval and Times, and then press Save. 3. After enable auto redial, calling out someone, if he is in busy, it will pop up a prompt box whether to auto redial, press OK, the phone will call out him according the Interval and Times that you set.
1. Press Menu ->Features-> Enter->Password Dial-> Enter. 2. Enable this function, you can also set Prefix and Length. For example，you want call out 1234567 and you set Password Dial Prefix 123 and Password Length 3, then enter the dial interface and input 1234567, and then the screen will show 123***7. 5.11 Action URL &...
2. You can enter the message and press Save, it will display in the phone screen when the phone start up. 6.7 Language 1. Press Menu ->Settings-> Enter->Basic Settings-> Enter->Language ->Enter. 2. DPH-150S/DPH-150SE support only one languages, you can’t use the navigation keys to choose. The default one languages is English. 7 Advanced Settings 7.1 Accounts Press Menu->Enter->Settings->Advanced settings, and then input the password to enter the...
Press Menu->Enter->Settings->Advanced settings, and then input the password to enter the interface. Then choose Factory Reset and press Enter, you can choose Yes or No. 8 Web configuration 8.1 Introduction of configuration 8.1.1 Ways to configure DPH-150S/DPH-150SE has three different ways to different users. Use phone keypad. / 68...
Use web browser (recommendatory way). Use telnet with CLI command. 8.1.2 Password Configuration Default user with root level: Username: admin Password: admin The default password of phone screen menu is 123. 8.2 Setting via web browser When this phone and PC are connected to network, enter the IP address of the wan port in this phone as the URL (e.g.
Information Field Name Explanation System Display equipment model, hardware version, software version, uptime, Last uptime Information and MEMinfo. Shows the configuration information for WAN port, including connection mode of Network WAN port (Static, DHCP, PPPoE), MAC address, IP address of WAN port. 220.127.116.11 Account Through this page, user can add or remove users depends on their needs and can modify existing user permission.
Account Field Name Explanation Change Web Authentication Password Can modify the login password to the account Add New User You can add new user User Accounts Show the existing user information 18.104.22.168 Configurations / 68...
Configurations Field Name Explanation Export Save the equipment configuration to a txt or xml file. Please note to Right Configurations click on the choice and then choose “Save Link As.” Import Browse to the config file, and press Update to load it to the equipment. Configurations Reset to factory This will restore factory default and remove all configuration information.
22.214.171.124 Auto Provision Auto Provision Field Name Explanation Common Settings Show the current config file’s version. If the version of configuration Current downloaded is higher than this, the configuration will be upgraded. If the Configuration endpoints confirm the configuration by the Digest method, the configuration Version will not be upgraded unless it differs from the current configuration Show the common config file’s version.
DHCP Option The equipment supports configuration from Option 43, Option 66, or a Option Value Custom DHCP option. It may also be disabled. Custom Option Custom option number. Must be from 128 to 254. Value SIP Plug and Play (PnP) If this is enabled, the equipment will send SIP SUBSCRIBE messages to a multicast address when it boots up.
126.96.36.199 Tools Syslog is a protocol used to record log messages using a client/server mechanism. The Syslog server receives the messages from clients, and classifies them based on priority and type. Then these messages will be written into a log by rules which the administrator has configured.
SIP Log Level Set the level of SIP log. Network Packets Capture Capture a packet stream from the equipment. This is normally used to troubleshoot problems. Reboot Phone Some configuration modifications require a reboot to become effective. Clicking the Reboot button will lead to reboot immediately.
DNS Server Select Configured mode DNS Server of the Configured by Primary DNS Enter the server address of the Primary DNS. Server Secondary DNS Enter the server address of the Secondary DNS. Server After entering the new settings, click the APPLY button. The equipment will save the new settings and apply them.
Advanced Field Name Explanation Link Layer Discovery Protocol (LLDP) Settings Enable LLDP Enable or Disable Link Layer Discovery Protocol (LLDP) Enables the telephone to synchronize its VLAN data with the Network Enable Learning Switch. The telephone will automatically synchronize DSCP, 802.1p, and Function VLAN ID values even if these values differ from those provided by the LLDP server.
802.1X Settings Enable 802.1X Enable or Disable 812.1X Username 802.1X user account Password 802.1X password 188.8.131.52 VPN The device supports remote connection via VPN. It supports both Layer 2 Tunneling Protocol (L2TP) and OpenVPN protocol. This allows users at remote locations on the public network to make secure connections to local networks.
Field Name Explanation VPN IP Address Shows the current VPN IP address. VPN Mode Enable VPN Enable/Disable VPN. L2TP Select Layer 2 Tunneling Protocol Select OpenVPN Protocol. (Only one protocol may be activated. After the OpenVPN selection is made, the configuration should be saved and the phone be rebooted.) Layer 2 Tunneling Protocol (L2TP) L2TP Server...
Field Name Explanation Basic Settings (Choose the SIP line to configured) Display the current line status at page loading. To get the up to date line Line Status status, user has to refresh the page manually. Username Enter the username of the service account. Display name Enter the display name to be sent in a call request.
Activate Whether the service of the line should be activated SIP Proxy Server Enter the IP or FQDN address of the SIP proxy server Address SIP Proxy Server Port Enter the SIP proxy server port, default is 5060 Outbound proxy Enter the IP or FQDN address of outbound proxy server provided by the address service provider...
Enable hotline configuration, the device will dial to the specific number Enable Hotline immediately at audio channel opened by off-hook handset or turn on hands-free speaker or headphone Hotline Number Set the hotline dialing number Enable Do-not-disturb, any incoming call to this line will be rejected Enable DND automatically Blocking Anonymous...
Use STUN Set the line to use STUN for NAT traversal Convert URI Convert not digit and alphabet characters to %hh hex code DTMF Type Set the DTMF type to be used for the line DTMF SIP INFO Set the SIP INFO mode to send ‘*’ and ‘#’ or ‘10’ and ‘11’ Mode Transportation Set the line to use TCP or UDP for SIP transmission...
RTP Encryption Enable RTP encryption such that RTP transmission will be encrypted RTP Encryption Key Set the pass phrase for RTP encryption 184.108.40.206 Dial Peer This functionality offers you more flexible dial rule, you can refer to the following content to know how to use this dial rule.
Dial Peer Field Name Explanation There are two types of matching conditions: one is full matching, the other is prefix matching. In the Full matching, you need input your desired phone number in this blank, and then you need dial the phone number to realize Number calling to what the phone number is mapped.
Call Mode Select different signal protocol, SIP Characters to be added at the end of the phone number. It is an optional Suffix item. Set the number of characters to be deleted. For example, if this is set to 3, Delete Length the phone will delete the first 3 digits of the phone number.
If your dialed phone number starts with When you dial “147”, your set phone number. The phone will the SIP1 server will send out your dialed phone number receive “1470011”. adding suffix number. 220.127.116.11 Dial Plan This system supports 4 dial modes: 1) End with “#”: dial your desired number, and then press #.
Send after Set the timeout of the last dial digit. The call will be sent after timeout. (3-30)seconds Enable Blind Transfer On Hook, when executing Blind Transfer End with Press # to Do Blind #, press # after inputting the number that you want to transfer, the phone Transfer will transfer the current call to the third party.
18.104.22.168 Basic Settings STUN – Simple Traversal of UDP through NAT –A STUN server allows a phone in a private network to know its public IP and port as well as the type of NAT being used. The equipment then use this information to register itself to a SIP server so that it can make and receive calls while in a private network.
STUN blinding period – STUN packets are sent at this interval to keep the Binding Period NAT mapping active. SIP Waiting Time Waiting time for SIP. This will vary depending on the network. SIP Line Using STUN(SIP1 or SIP2) Use STUN Enable/Disable STUN on the selected line.
Common Settings Field Name Explanation DND might be disabled phone for all SIP lines, or line for SIP individually. DND Mode But the outgoing calls will not be affected Ban Outgoing If enabled, no outgoing calls can be made. Enable this setting to allow user to take second incoming call during an Enable Call Waiting established call.
Code Enable Password Dial by selecting it, When number entered is beginning with the password prefix, the following N numbers After the password prefix will Enable Password be hidden as *, N stand for the value which you enter in the Password Length Dial field.
22.214.171.124 Audio In this page, you can configure voice codec, input/output volume and so on. Audio Setting Field Name Explanation First Codec The first codec choice: G.711A/U, G.722, G.723.1, G.726-32, G.729AB The second codec choice: G.711A/U, G.722, G.723.1, G.726-32, G.729AB, Second Codec None The third codec choice: G.711A/U, G.722, G.723.1, G.726-32, G.729AB,...
Volume Headset Volume Set the headset calls the volume level. Speakerphone Set the speaker ring the volume grade. Ring Volume Headset Volume Set the headset the Volume the Offset. Offset Headset Mic Set the headset MIC the Offset. Offset G.729AB Payload G.729AB Payload Length –...
device, monitor and play the RTP stream which sent by the multicast address. MCAST Settings Equipment can be set up to monitor up to 10 different multicast addresses, used to receive the multicast RTP stream sent by the multicast address. Here are the ways to change equipment receiving multicast RTP stream processing mode in the Web interface: set the ordinary priority and enable page priority.
Blue part (name) "Group 1","Group 2" and "Group 3" are your setting monitoring multicast name.The group name will be displayed on the screen when you answer the multicast. If you have not set, the screen will display the IP: port directly. ...
current call "priority group 2" 3, so multicast call will can come in. If multicast is a new "group of 3", because "the priority group 3" is 4, lower than the current call "priority group 2" 3, "1" will listen to the equipment and maintain the "group of 2".
Time/Date Field Name Explanation Network Time Server Settings Time Synchronized Enable time-sync through SNTP protocol via SNTP Time Synchronized Enable time-sync through DHCP protocol via DHCP Primary Time Server Set primary time server address Secondary Time Set secondary time server address, when primary server is not reachable, the device Server will try to connect to secondary time server to get time synchronization.
126.96.36.199 Advanced Advanced Field Name Explanation Screen Configuration Enable Enable Energysaving by selecting it. Energysaving Backlight Time Set the Backlight Time. LCD Menu Password Settings Set the password for entering the Advanced setting menu of the phone. The Menu Password password is digit.
188.8.131.52 Trusted Certificates User may Update or Delete Certificates File in this webpage. 8.3.5 Phonebook 184.108.40.206 Contacts User can add, delete, or edit contacts in the phonebook in this page. User can browse the phonebook and sorting it by name, phones, or filter them out by group. To add a new contact, user should enter contact’s information and press “Add”...
220.127.116.11 Cloud phonebook Cloud phonebook Field Name Explanation Manage Cloud Phonebooks User may configure up to 8 cloud phonebooks. Each cloud phonebook must be configured with an URL where an XML phonebook is stored. The URL may be based on HTTP/HTTPs or FTP protocol with or without authentication.
Search Base (must) Access username (optional) Access password (optional) 18.104.22.168 Blacklist By adding a number into the blacklist, user will no longer receive phone call from that number and it will be rejected automatically by the device until user delete it from the blacklist.
8.3.6 Call logs User can browse complete call logs in this page, order the call logs by time, caller ID, contact name, duration, or line, and can also filter the call logs by the call log types, in, out, missed, or all. User can save a call log into his/her phonebook or add it to the blacklist.
Function Key Field Name Explanation Function Key Settings Memory Key BLF(NEW CALL/BXFE /AXFER): It is used to prompt user the state of the subscribe extension, and it can also pick up the subscribed number, which help user monitor the state of subscribe extension (idle, ringing, a call). There are 3 types for one-touch BLF transfer method.
22.214.171.124 EXT Key The device support 3 Extension module. User may configure/customize each DSS key in this webpage. 126.96.36.199 Softkey User can configure different functions in different screens for each softkey. / 68...
switch to other line to call. 9 kinds of ring types. DTMF Relay: support SIP info, DTMF Relay, RFC2833 SIP application: SIP Call forward/transfer（blind/attended）/hold/waiting/3 way talking/SMS/pickup /join call /redial /unredial/multi line/intercom/BLF/presence/push to talk/auto redial/call return Call control features: Flexible dial map, hotline, empty calling No. reject service, black list for reject authenticated call, white list, limit call, no disturb, caller ID, CLIR(reject the anonymous call), CLIP(make a call with anonymous), Dial without register.
Support VPN (L2TP/OPEN VPN) function Wan Port supports main DNS and secondary DNS server can select dynamically to get DNS in DHCP mode or statically set DNS address. Support DHCP client on WAN Support DHCP server on LAN ...