Related Manuals for SHOWTEC 42486
Summary of Contents for SHOWTEC 42486
- Page 1 Studiobeam Tour Q4 4-in-1 LED ORDERCODE 42486 Highlite International B.V. Vestastraat 2 6468 EX Kerkrade The Netherlands Phone: +31 45-5667700...
- Page 2 Congratulations! You have bought a great, innovative product from Showtec. The Showtec Studiobeam Tour Q4 LED brings excitement to any venue. Whether you want simple plug-&- play action or a sophisticated DMX show, this product provides the effect you need.
-
Page 3: Table Of Contents
Showtec Showtec Studiobeam Tour Q4 LED Product Guide ™ Warning ....................................2 Safety Instructions ................................. 2 Operating Determinations ............................4 Rigging .................................... 4 Return Procedure ................................5 Claims ....................................5 Description of the device ..............................6 Overview ..................................6 Set Up and Operation ............................... 7 Control Modes ................................ -
Page 4: Warning
Warning FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL CAREFULLY BEFORE YOUR INITIAL START-UP! Unpacking Instructions Immediately upon receiving this product, carefully unpack the carton and check the contents to ensure that all parts are present, and have been received in good condition. Notify the dealer immediately and retain packing material for inspection if any parts appear damaged from shipping or the carton itself shows signs of mishandling. - Page 5 If your Showtec device fails to work properly, discontinue use immediately. Pack the unit securely (preferably in the original packing material), and return it to your Showtec dealer for service.
-
Page 6: Operating Determinations
Operating Determinations • This device is not designed for permanent operation. Consistent operation breaks will ensure that the device will serve you for a long time without defects. • The minimum distance between light-output and the illuminated surface must be more than 1.5 meter. •... -
Page 7: Return Procedure
Connection with the mains Connect the device to the mains with the power-plug. Always pay attention, that the right color cable is connected to the right place. International EU Cable UK Cable US Cable BROWN YELLOW/COPPER FASE BLUE BLACK SILVER YELLOW/GREEN GREEN GREEN... -
Page 8: Description Of The Device
Description of the device Features The Showtec Studiobeam Tour Q4 LED is a LED parcan with high output and great effects. • Never change lamps again! • Powersupply: 100-240V multi-voltage • Q4 Technology • Neutrik Powercon in and output • 3 Pole Neutrik XLR Data connection •... -
Page 9: Set Up And Operation
Set Up and Operation Follow the directions below, as they pertain to your preferred operation mode. Before plugging the unit in, always make sure that the power supply matches the product specification voltage. Do not attempt to operate a 120V specification product on 230V power, or vice versa. Damages caused by non-observance are not subject to warranty. -
Page 10: Multiple Studiobeams Tour Q4 Led (Dmx Control)
Multiple Studiobeams Tour Q4 LED (DMX Control) 1. Fasten the effect light onto firm trussing. Leave at least 0,5 meter on all sides for air circulation. 2. Always use a safety cable (ordercode 70140 / 70141). Use a 3-p XLR cable to connect the LED Studiobeams and other devices. Link the units as shown in (figure 5), Connect a DMX signal cable from the first unit's DMX "out"... -
Page 11: Fixture Linking
Fixture Linking You will need a serial data link to run light shows of one or more fixtures using a DMX-512 controller or to run synchronized shows on two or more fixtures set to a master/slave operating mode. The combined number of channels required by all the fixtures on a serial data link determines the number of fixtures the data link can support. -
Page 12: Control Panel
The Studiobeam Tour Q4 LED can be operated with a controller in control mode or without the controller in stand-alone mode. Control Panel Fig. 6 A. LCD Display C. Up Button B. MODE button D. Down Button DMX Control Mode The fixtures are individually addressed on a data-link and connected to the controller. -
Page 13: Menu Overview
Menu Overview Display OFF Display OFF after 10 sec. Display ON by holding down any button for 3 seconds. 4CH Mode: CH1=Red, CH2=Green, CH3=Blue, CH4= Dimmer 6CH Mode: CH1=Red, CH2=Green, CH3=Blue, CH4= Dimmer CH5= Master Dimmer, CH6= Strobe Slave 20 Macro Colors 9 Built-in Programs Program Speed from slow to fast Sound-controlled Mode... -
Page 14: Dmx Mode 4 Channels
3. DMX Mode 4 Channels 1) Press the MODE button on the device, until the display shows 2) The Studiobeam is now in 4 Channel Mode. 3) Use the UP/Down buttons to change the intensity of each color from CH1=Red, CH2=Green, CH3=Blue and CH4= White 4. -
Page 15: Manual Control
10. Manual Control 1) Press the MODE button on the device, until the display shows 2) With these menus you can manually set the intensity of Red, Green, Blue and White. Red, from 0 -100% Green, from 0 -100% Blue, from 0 -100% White, from 0 -100% DMX Channels 4 Channels... -
Page 16: Maintenance
3. Mechanically moving parts like axles, eyes and others may not show any traces of wearing. 4. The electric power supply cables must not show any damages or material fatigue. The Showtec Studiobeam Tour Q4 LED requires almost no maintenance. However, you should keep the unit clean. - Page 17 Problem Probable cause(s) Remedy No power to the fixture • Check that power is switched on One or more and cables are plugged in. fixtures are Primary fuse blown. • Replace fuse. completely dead. Fixtures reset The controller is not connected. •...
-
Page 18: Product Specification
Product Specification Model: Showtec Studiobeam Tour Q4 LED Powersupply: 100-240V multi-voltage Q4 Technology Neutrik Powercon in and output 3 Pole Neutrik XLR Data connection Peak Power 100 Watt Continuous Power 100 Watt LEDs: 18x 4-in-1 LED 5W (RGBW) Control: Manual, Auto, Music, Master/Slave, DMX-512...