Related Manuals for SHOWTEC Wipe Out 3W
Summary of Contents for SHOWTEC Wipe Out 3W
- Page 1 MANUAL ENGLISH Wipe Out 3W Ordercode: 42567 Highlite International B.V. – Vestastraat 2 – 6468 EX – Kerkrade – the Netherlands...
-
Page 2: Table Of Contents
Wipe Out 3W Table of contents Warning ....................................2 Safety Instructions ................................. 2 Operating Determinations ............................4 Rigging .................................... 4 Connection with the mains............................5 Return Procedure ................................5 Claims ....................................5 Description of the device ..............................6 Overview ..................................7 Installation ................................... -
Page 3: Warning
Save the carton and all packing materials. In the event that a fixture must be returned to the factory, it is important that the fixture be returned in the original factory box and packing. Your shipment includes: ● Showtec Wipe Out 3W ● IEC power cable (1,5m) ●... - Page 4 For replacement use fuses of same type and rating only. The user is responsible for correct positioning and operating of the Wipe Out 3W. The manufacturer will not accept liability for damages caused by the misuse or incorrect installation of this device.
-
Page 5: Operating Determinations
The Wipe Out 3W can be placed on a flat stage floor or mounted to any kind of truss with a clamp. Improper installation can cause serious damage to people and property ! -
Page 6: Connection With The Mains
Wipe Out 3W Connection with the mains Connect the device to the mains with the power-plug. Always pay attention, that the right color cable is connected to the right place. International EU Cable UK Cable US Cable BROWN YELLOW/COPPER FASE... -
Page 7: Description Of The Device
Wipe Out 3W Description of the device Features The Showtec Wipe Out 3W is a compact and powerful fixture for both indoor and outdoor use. ● Input Voltage: 100-240 VAC, 60/50Hz ● Power consumption: 50W ● LED Quantity: 8 x 3W Cool White High Power LED, Cool White 4200K ●... -
Page 8: Overview
Wipe Out 3W Overview Fig. 01 01) 8 x 3W Cool White High Power LED 02) 3-pin DMX signal connector IN 03) IEC power connector 100-240V IN + Fuse T2AL/250V 04) Ground/earth connection 05) Power switch ON/OFF 06) LCD display + menu buttons... -
Page 9: Installation
Wipe Out 3W Installation Remove all packing materials from the Wipe Out 3W. Check that all foam and plastic padding is removed. Connect all cables. Do not supply power before the whole system is set up and connected properly. Always disconnect from electric mains power supply before cleaning or servicing. -
Page 10: Multiple Wipe Outs (Dmx Control)
Wipe Out 3W Multiple Wipe Outs (DMX Control) 01) Fasten the effect light onto firm trussing. Leave at least 0,5 meter on all sides for air circulation. 02) Always use a safety cable (ordercode 70140 / 70141). 03) Plug the end of the electric mains power cord into a proper electric power supply socket. -
Page 11: Fixture Linking
Wipe Out 3W Fixture Linking You will need a serial data link to run light shows of one or more fixtures using a DMX-512 controller or to run synchronized shows on two or more fixtures set to a master/slave operating mode. The combined number of channels required by all the fixtures on a serial data link determines the number of fixtures the data link can support. -
Page 12: Control Panel
Wipe Out 3W The Wipe Out can be operated with a controller in control mode or without the controller in stand-alone mode. Control Panel LCD Display MODE button SETUP Button UP Button DOWN Button Fig. 04 Control Mode The fixtures are individually addressed on a data-link and connected to the controller. -
Page 13: Menu Overview
Wipe Out 3W Menu Overview Ordercode: 42567... -
Page 14: Main Menu Options
Wipe Out 3W Main Menu Options Auto Run Mode Built-in programs Sound-controlled Mode DMX-512 Mode Master/Slave Mode Settings 1. Auto Run Mode With this menu you can set Auto Run mode of the Wipe Out. 01) Press the MODE button until the display shows 02) Press the SETUP button to open the menu. -
Page 15: Bar Menu
Wipe Out 3W 04) Press the SETUP button to enter the desired menu. 05) When the display shows , press the SETUP button to enter the LED speed settings. 06) Press the UP/DOWN buttons to increase/decrease the LED speed. The adjustment range is between , from slow to fast. -
Page 16: Built-In Programs
03) Press the UP/DOWN buttons to set the sound sensitivity. The adjustment range is between , from low to high sensitivity. 04) Turn the music on and the Wipe Out 3W will react to the beat of the music. 4. DMX-512 Mode With this menu you can set the DMX address. -
Page 17: Settings
Wipe Out 3W 6. Settings With this menu you can manually adjust the device’s settings. 01) Press the MODE button until the display shows 02) Press the SETUP button to open the menu. 03) Press the UP/DOWN buttons to toggle between the following 6 options:... -
Page 18: Dmx Channels
Wipe Out 3W 10) Once you have set the desired value and confirmed it, your device will remain tilted. When you want to return to the basic horizontal setting, please reset your Wipe Out and return to its factory default settings. -
Page 19: Channels
Wipe Out 3W 12 Channels Channel 1 – Left Bar Tilt movement 0-180 Gradual tilt movement, from 0-180° 181-255 Not functional Channel 2 – Left Bar Tilt movement speed 0-255 Gradual speed adjustment, from slow to fast Channel 3 – Right Bar Tilt movement 0-180 Gradual tilt movement, from 0-180°... -
Page 20: Channels
Wipe Out 3W 16 Channels Channel 1 – Left Bar Tilt movement 0-180 Gradual tilt movement, from 0-180° 181-255 Not functional Channel 2 – Left Bar Tilt movement speed 0-255 Gradual speed adjustment, from slow to fast Channel 3 – Right Bar Tilt movement 0-180 Gradual tilt movement, from 0-180°... -
Page 21: Maintenance
Flash frequency adjustment, from low to high frequency Maintenance The Showtec Wipe Out requires almost no maintenance. However, you should keep the unit clean. Otherwise, the fixture’s light-output will be significantly reduced. Disconnect the mains power supply and then wipe the cover with a damp cloth. Wipe the front glass panel clean with glass cleaner and a soft cloth. -
Page 22: Troubleshooting
Response: Suspect three potential problem areas as: the power supply, the LEDs, the fuse. 01) Power supply. Check that the unit is plugged into an appropriate power supply. 02) The LEDs. Return the Wipe Out to your Showtec dealer. 03) The fuse. Replace the fuse. See page 20 for replacing the fuse. - Page 23 Wipe Out 3W Problem Probable cause(s) Remedy One or more No power to the fixture. ● Check if power is switched on and fixtures do not cables are plugged in. function at all. Primary fuse blown. ● Replace fuse. Fixtures reset The controller is not connected.
-
Page 24: Product Specification
Wipe Out 3W Product Specification Model: Showtec Wipe Out 3W Input Voltage: 100-240 VAC Continuous Power: Fuse: T2AL / 250V Dimensions: 1065 x 85 x 145 mm (LxWxH) Weight: 8,6 kg Operation and Programming Signal pin OUT: pin 1 earth, pin 2 (-), pin 3 (+) -
Page 25: Dimensions
Wipe Out 3W Dimensions Ordercode: 42567... -
Page 26: Notes
Wipe Out 3W Notes Ordercode: 42567... - Page 27 Wipe Out 3W Ordercode: 42567...
- Page 28 ©2015 Showtec...