Powerspot 10 SW White Warning Unpacking Instructions Immediately upon receiving this product, carefully unpack the carton and check the contents to ensure that all parts are present, and have been received in good condition. Notify the dealer immediately and retain packing material for inspection if any parts appear damaged from shipping or the carton itself shows signs of mishandling.
Page 4
• If your Showtec device fails to work properly, discontinue the use immediately. Pack the unit securely (preferably in the original packing material), and return it to your Showtec dealer for service.
Powerspot 10 SW White • The user is responsible for correct positioning and operating of the Powerspot 10 SW. The manufacturer will not accept liability for damages caused by the misuse or incorrect installation of this device. • This device falls under protection class I. Therefore it is essential to connect the yellow/green conductor to earth.
Powerspot 10 SW White The Powerspot 10 SW can be placed on a flat stage floor or mounted to any kind of truss with a clamp. Improper installation can cause serious injuries and/or damage of property! Connection with the mains Connect the device to the mains with the power-plug.
Powerspot 10 SW White Return Procedure Returned merchandise must be sent prepaid and in the original packing, call tags will not be issued. Package must be clearly labeled with a Return Authorization Number (RMA number). Products returned without an RMA number will be refused. Highlite will not accept the returned goods or any responsibility.
Powerspot 10 SW White Description of the device Features The Powerspot 10SW brings the right white tone to your stage or venue. It is equipped with 10 pieces LED which are built out of cool white, warm white and amber in one single chip ensuring a perfect white balance.
Powerspot 10 SW White Backside Fig. 02 04) LCD display + control buttons 05) 5-pin DMX signal connector IN 06) 3-pin DMX signal connector IN 07) Blue Pro Power connector 100-240V IN 08) White Pro Power connector 100-240V OUT 09) 3-pin DMX signal connector OUT...
Powerspot 10 SW White Control Modes There are 6 modes: • Auto run • Built-in programs • Static Color (dimmer) • Sound-controlled • Master/slave • DMX-512 (3CH, 6CH or 7CH) One Powerspot 10 SW (Auto Run Mode, Built-in programs and Static Color Mode) 01) Fasten the effect light to a firm trussing.
Powerspot 10 SW White Multiple Powerspots 10 SW (DMX Control) 01) Fasten the effect light to a firm trussing. Leave at least 0,5 meter on all sides for air circulation. 02) Always use a safety cable (ordercode 70140 / 70141).
Powerspot 10 SW White Fixture Linking You will need a serial data link to run light shows of one or more fixtures using a DMX-512 controller or to run synchronized shows of two or more fixtures set to a master/slave operating mode. The combined number of channels required by all the fixtures on a serial data link determines the number of fixtures the data link can support.
Powerspot 10 SW White Control Panel A) LCD display MODE button C) SETUP button D) UP button DOWN button Fig. 05 Control Mode The fixtures are individually addressed on a data-link and connected to the controller. The fixtures respond to the DMX signal from the controller. (When you select the DMX address and save it, the controller will display the saved DMX address, next time.)
Powerspot 10 SW White Main Menu Options Auto run Built in programs Static Color Mode Sound-controlled Mode DMX address / DMX configuration Slave mode Settings Info Auto Run Mode With this menu you can start the Auto Run program of the Powerspot 10 SW.
Powerspot 10 SW White 08) Use the UP/DOWN buttons to change the values. Speed from 00-100 Flash Frequency from 00-99 Static Color control With this menu you can manually set a desired color. 01) Press the MODE until the display shows 02) Press the SETUP button to open this menu.
Powerspot 10 SW White Settings With this menu you can set various options. 01) Press the MODE button until the display shows 02) Press the SETUP button to open this menu. 03) Use the UP/DOWN buttons to choose between the 2 options.
Powerspot 10 SW White DMX Channels 3 channels Channel 1 – Amber Dimmer intensity 0-255 Amber from 0-100% Channel 2 – Warm White Dimmer intensity 0-255 Warm White from 0-100% Channel 3 – Cool White Dimmer intensity 0-255 Cool White from 0-100% 6 channels Channel 1 –...
Page 19
Powerspot 10 SW White Channel 4 – Cool White Dimmer intensity ( CH1 must be set between 001-255 and CH5 between 0-24 0-255 Cool White from 0-100% Channel 5 – Dimming/Program/Sound mode 0-24 Dimming mode 25-49 Auto run 50-74 Built-in program 1...
01) Power supply. Check that the unit is plugged into an appropriate power supply. 02) The LEDs. Return the Powerspot to your Showtec dealer. 03) The internal fuse. Return the Powerspot to your Showtec dealer. 04) If all of the above appears to be O.K., plug the unit in again.
Page 21
Powerspot 10 SW White Problem Probable cause(s) Solution No power to the fixture • Check if power is switched on and One or more cables are plugged in fixtures do not function at all Internal fuse blown • Return the Powerspot to your...