Table of Contents
Advertisement
Maintenance
(continued)...................................
How to Remove Range
Proportional
Valve Adjustment
for Cleaning and Servicing
for Surface Burners
Follow these procedures to remove appliance for cleaning
The WARM setting should pro-
or servicing:
duce a stable flame when turn-
1. Shut off gas supply to appliance,
ing the knob from HIGH to
WARM. The flame should be
2. Disconnect electrical supply to appliance, if equipped.
_/sinch or lower and must be
3. Disconnect gas supply tubing to appliance,
stable on all ports on WARM
setting.
4• Slide range forward to disengage range from the anti-tip
bracket. (See Installation Instructions for location of
To adjust: Operate burner on HIGH for about five rain-
bracket.)
utes to preheat burner cap. Turn knob back to WARM; re-
move knob, and insert a small screwdriver into the center
5. Reverse procedure to reinstall. If gas line has been dis-
of the valve stem. Adjust the flame size by turning adjust-
connected, check for gas leaks after reconnection. NOTE:
merit screw in either direction, while holding the stem.
A qualified servicer should disconnect and reconnect the
Flame must be of sufficient size to be stable on all burner
gas supply,
ports. If flame adjustment is needed, adjust ONLY on the
6. To prevent range from accidentally tipping, range must
WARM setting. Never adjust flame size on a higher set-
be secured to the floor by sliding rear leveling leg into the
ting.
anti-tip bracket.
NOTE: All gas adjustments should be done by a quali-
fied servicer only.
Before
You Call for Service ......................
Check these )oints if...
• Check to be sure plug is securelyinserted into receptacle.
Part or all of the
• Check or re-setcircuit breaker. Check or replace fuse.
appliance does not
work.
• Check power supply.
• Check if surface and/or oven controls have been properly set. See pages 6 and 8.
•
•
•
• •
•
•
0 •
• •
•
•
•
•
•
,
•
* •
•
*
•
•
• •
•
•
*
• •
*
•
•
•
•
• •
•
•
•
•
• •
•
•
•
• •
•
•
•
* •
•
•
•
• •
•
•
• •
"
• Check to be sure unit is properly connectedto power supply.
• Check for a blown circuitfuse or a tripped main circuit breaker.
Surface burner
fails to light.
• Check to be sure burner ports or ignitionports are not clogged. See page 6.
• Check to be sureignitor is dry andclicking. Burnerwill not lightif ignitor is damaged,soiled orwet.
If ignitor doesn't click, turn controlknob OFF.
•
,
•
• •
•
•
• •
•
•
•
•
•
•
•
,
,
• •
,
•
•
•
• *
•
•
•
• •
•
•
•
•
*
• •
,
•
•
•
•
•
•
•
,
• •
,
•
•
,
•
•
•
•
• •
•
•
•
• *
The flame
• Burnerports may be clogged.
is uneven•
• Flame setting may need to be adjusted.
............ m" .... ....... i ";;.... o........................
Surface burner fla e
•
eck tob surea pan is siting on h grateab ve.
lifts off ports•
Baking results differ
• Temperaturesoften varybetween a new oven and an old one. As ovens age, the oven temperature
from previous oven.
ofteu"drifts"and maybecome hotler or cooler.
13
Advertisement
Table of Contents
