1. Manuals
  2. Brands
  3. Powercom Manuals
  4. UPS
  5. 1000AP
  6. User manual

Powercom 1000AP User Manual

Line interactive sine wave 1000va – 3000va
Hide thumbs Also See for 1000AP:

Advertisement

Table of Contents

U P S
Line Interactive Sine Wave
1000VA – 3000VA
■USER'S MANUAL■

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 1000AP and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Powercom 1000AP

Summary of Contents for Powercom 1000AP

  • Page 1 U P S Line Interactive Sine Wave 1000VA – 3000VA ■USER‘S MANUAL■...

  • Page 2: Important Safety Instructions

    MPORTANT AFETY NSTRUCTIONS IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS CAUTION (UPS having internal batteries): Risk of electric shock - Hazardous live parts inside this  unit are energized from the battery supply even when the input AC power is disconnected. CAUTION (No user serviceable parts): Risk of electric shock, do not remove cover.

  • Page 3: Table Of Contents

    ABLE OF CONTENTS Important Safety Instructions ...................... 2 Table of contents ........................3 Save these instructions ....................... 4 1. Presentation .......................... 5 2. Installation ..........................8 3. Operation ..........................10 4. Alarm ..........................11 5. Software and Interface Port ....................12 6.

  • Page 4: Save These Instructions

    AVE THESE INSTRUCTIONS Please read and save this manual! Thank you for selecting this uninterruptible power system (UPS). It provides you with a perfect protection for connected equipment. The manual is a guide to install and use the UPS. It includes important safety instructions for operation and correct installation of the UPS.

  • Page 5: Presentation

    1. P RESENTATION Front LED Panel 1.1.1 “ON/TEST” button: With the UPS plugged in, press the ON/TEST button to turn on the UPS and power the loads. ON/TEST also activates the UPS‘s self-test and utility line voltage displays. 1.1.2 “OVERLOAD” indicator: The LED lights when the loads connected to the UPS exceed the UPS‘s capacity.
  • Page 6 1.1.8 “LOAD CAPACITY” bar: The display shows the power being drawn by the load. 1.1.9 “BATTERY CAPACITY” bar: The display shows the present battery charge as a percentage of battery capacity. Load Indicator % of Load Value Battery Indicator % of Bat Level Light no.5 over 81% Light no.5...
  • Page 7 3000VA 1.2.1 “TEL./MODEM” connector Telecom transfer ports provide users to extend the applications. CAUTION: To reduce the risk of fire, use only No. 26AWG or larger telecommunication line cord. 1.2.2 “EXTERNAL BATTERY PACK” connector (optional) CAUTION: Use only factory supplied or authorized connecting cable for external battery! 1.2.3 “OUTPUT”...

  • Page 8: Installation

    2. I NSTALLATION Inspect the UPS upon receipt. The packaging is recyclable; keep it for reuse or be disposed of properly. Placement: Install the UPS in a protected area with adequate flowing air and free of excessive dust. Do not operate the UPS where the temperature and humidity is out of the specified limits.
  • Page 9 Installation with accessories of “Rack-mounted” types: Please install the types of units according to the following illustration. Installation with accessories of “Stack” types: Please install the types of units according to the following illustration.

  • Page 10: Operation

    3. O PERATION Switch on: While utility input is connected to the UPS, press the "ON" button and keep pressing over than 1 second. After that, connect the electrical cords of the equipment that is going to be used such as computer or monitor with the terminal on the rear panel of UPS. Don't overload the machine with all the equipment used.

  • Page 11: Alarm

    Cold start: When the UPS is off and there is no utility power, use the cold start feature to apply power to the loads from UPS‘s battery. Press the ON/TEST button until the UPS beeps. Shutdown mode: In shutdown mode the UPS stops supplying power to the load, waiting for return of utility power.

  • Page 12: Software And Interface Port

    “FAULT” (continuous alarm): Here is listing some “FAULT” conditions as following for reference. 4.3.1 ALL LED flashing: The UPS emits continuous beeps and the “FAULT” illuminates when UPS fails. 4.3.2 Overload indicator: When the UPS is working under overload condition (the connected loads exceed the maximum rated capacity), the UPS will emit continuous alarm to warn an overload condition.
  • Page 13 The pin of computer interface port: The pin of computer interface port has the following characteristics: 5.4.1. Pin 6 and 8 are open collector outputs that must be pulled up to a common referenced supply no greater than DC +40V. The transistors are capable of a maximum nonconductive load of DC 25 mA, Use only pin 5 as the common.

  • Page 14: Maintenance And Storage

    6. M AINTENANCE AND TORAGE Maintenance 6.1.1. Keep the unit clean and vacuum the ventilation intake periodically. 6.1.2. Wipe with soft loose and damp cloth. 6.1.3. Check for loose and bad connections monthly. 6.1.4. Never leave the unit on an uneven surface. 6.1.5.

  • Page 15: Appendix A Troubleshooting

    PPENDIX A ROUBLESHOOTING Problems Possible Reasons Solutions Input power source mistake Check out the power source Non-fuse switch on the rear Press the non-fuse switch to its "on" panel hasn't been opened position UPS can't operate after pressing On/Off Time of pressing the ON Keep pressing the ON button over 1 second switches button is too short...

  • Page 16: Appendix B. Specification

    PPENDIX B PECIFICATION Model 1000AP 1500AP 2000AP 3000AP 1000VA / 1500VA / 2000VA / 3000VA / Capacity 900W 1350W 1800W 2700W Voltage 220V, 230V, 240V (adjustable from 149.5V to 310V) INPUT Frequency 50Hz / 60Hz ±10% auto sensing On Battery: Pure sine wave at +/-5% nominally,...

This manual is also suitable for:

1500ap2000ap3000ap

Table of Contents

Save PDF