Advertisement
Location and Function of Parts and Controls
8 CHARACTER (character signal output)
connector (BNC type)
Supplies the self-diagnostic results of this unit as a
video signal.
9 WF1 and WF2 (waveform monitor 1 and 2
output) connectors (BNC type)
Supply the video signals for a waveform monitor.
The MONITOR SELECT buttons on an RCP-700-
series unit select the signal output from the WF 1
connector, and the WAVEFORM MONITOR
buttons on the MSU-700 select the signal output
from the WF 2 connector.
0 PIX1 and PIX2 (picture monitor 1 and 2
output) connectors (BNC type)
Supply the video signals for a picture monitor.
The MONITOR SELECT buttons on an RCP-700-
series unit select the signal output from the PIX 1
connector, and the PICTURE MONITOR buttons
on the MSU-700 select the signal output from the
PIX 2 connector.
!¡ VBS1, VBS2, and VBS3 (composite video
signal 1, 2, and 3 output) connectors
(BNC type)
Supply composite video signals (VBS) from the
video camera.
!™ SYNC (sync signal output) connector
(BNC type)
Supplies the sync signals (0.3 Vp-p, 75 ohms)
generated by the built-in sync signal generator.
Connect to the sync signal input connector of a
waveform monitor or picture monitor.
!£ ⁄AC IN (AC power input) connector
Connect to an AC power source using the supplied
AC power cord. The power cord can be fixed to
the CCU-700A/700AP using the supplied plug
holder.
!¢ WF MODE (waveform monitor mode)
connector (4-pin)
Connect to the corresponding connector of a
waveform monitor to monitor signals in sequential
mode. A sequential control signal is output from
this connector when you press the SEQ button on
an RCP-700-series unit, which enables
simultaneous monitoring of the R, G, and B
signals.
6
!∞ RCP/CNU REMOTE (remote control panel/
camera command network unit remote
control) connector (8-pin)
Connect an MSU-700, CNU-700, or RCP-700-
series unit using a CCA-5 cable. Control signals
are then accepted. When an RCP-700-series unit is
connected, the power is also supplied to the unit.
!§ AUX (auxiliary) REMOTE connector (8-pin)
Connect an external system. For details on
connections, refer to the authorized Sony
representative.
Note
If you connect an RCP-700-series unit to the RCP/
CNU REMOTE connector, this connector cannot
supply power to the connected equipment.
!¶ SERIAL OUTPUT 1, 2, and 3 (serial digital
video signal 1, 2, and 3 output) connectors
(BNC type)
Signals sent from the video camera are converted
into serial digital video signals and are supplied
from these connectors. These connectors function
when an optional BKP-7311 SDI output board is
installed in the CCU-700A/700AP. Connect these
connectors to the input connectors of a digital
video switcher, component digital VTR, etc.
!• SERIAL INPUT RET 1 and RET 2 (serial
digital return video signal 1 and 2 input)
connectors (BNC type)
These connectors accept a 10-bit 4:2:2 component
serial digital video signals as return video signals.
They function when an optional BKP-7312 SDI
input board is installed in the CCU-700A/700AP,
and function as return video 1 and 2 input
connectors.
When the BKP-7312 is installed, nothing sould be
connected to the RET 1 and RET 2 connectors in
the ANALOG INPUT block.
!ª Spare connectors (BNC type)
@º COAX (coaxial) connector (BNC type)
Accepts and supplies triax signals by setting a
switch on the internal DM board. The unit cannot
supply power to the video camera through this
connector. For connection, use a coaxial cable.
When a return video function is used, the
maximum cable length of a 5C-2V (RG-6A/U)
coaxial cable is 1,000 m (3,280 feet) for a long
triax signal or 800 m (2,624 feet) for a wide triax
signal.
Advertisement
