Table of Contents
Advertisement
Quick Links
CONTENTS
O P E R A T I N G
M A N U A L
FIBARO KEYFOB
FGKF-601
3
4
5
6
7
8
10
EN
v1.0
11
12
13
15
19
20
Advertisement
Table of Contents
Related Manuals for FIBARO KEYFOB FGKF-601
Summary of Contents for FIBARO KEYFOB FGKF-601
-
Page 1: Table Of Contents
O P E R A T I N G M A N U A L FIBARO KEYFOB FGKF-601 CONTENTS v1.0 #1: Description and features #8: Activating scenes #2: Basic activation #9: Battery #3: Adding/removing the device #10: Associations #4: Operating the device... -
Page 2: Fgkf
Compliance with safety standards: The device is designed to be used in Z-wave home automation sys- tems (e.g. FIBARO) and is complaint with IEC/UL/CSA 60950-1. In case of the integration with another system, e.g. alarm system, it is re- quired to verify the compliance with additional standards. -
Page 3: 1: Description And Features
Six buttons allow you to control other devices through the Z-Wave network and run various scenes defined in FIBARO System. Configure actions for one, two, three clicks, holding the button and button sequences to suit all your needs. -
Page 4: 2: Basic Activation
#2: Basic activation 1. Using included keyring or a coin, open the battery cover by turning it counter-clockwise. 2. Remove sticker protecting the battery. 3. Using included keyring or a coin, close the battery cover by turning it clockwise. 4. Locate the device nearby the main Z-Wave controller. 5. -
Page 5: 3: Adding/Removing The Device
#3: Adding/removing the device Adding (Inclusion) - Z-Wave device learning mode, allowing to add NOTE the device to existing Z-Wave network. Adding Security To add the device: Mode must be per- 1. Set the main Z-Wave controller in (Security/non-Security Mode) formed up to 2 meters from the controller. -
Page 6: 4: Operating The Device
#4: Operating the device Menu allows to perform Z-Wave network actions. In order to use the menu: 1. Click simultaneously. 2. Click until LED indicates desired menu position with colour: • White - wake up the device • Green - learning mode (adding/removing) NOTE •... -
Page 7: 5: Visual Indications
#5: Visual indications Visual indications: The KeyFob is equipped with a LED diode, signalling pushing the but- tons, sequences, menu position and status of the device. Indications for scenes and associations: After pressing one of the buttons or using sequence, KeyFob indi- cates status of action with the LED diode. -
Page 8: 6: Lock Mode
#6: Lock Mode The KeyFob can be protected with a sequence of 2 to 5 button clicks. When unlocking sequence is set, the device will lock itself after: • being inactive for time set in parameter 2 (60 seconds by default), •... - Page 9 Setting the unlocking sequence using advanced parameter: 1. Calculate value of parameter using table and formula: Button Value Value of parameter = Value of first button + + 8 * Value of second button + 64 * Value of third button + + 512 * Value of fourth button + 4096 * Value of fifth button 2.
-
Page 10: 7: Sequences
#7: Sequences Sequences: User can create sequences of two to five button to expand number of possible actions. Every sequence sends corresponding Scene ID to the Z-Wave controller with attribute "Key pressed 1 time" (see "Scene activation" on page 11). Sequences are saved in advanced parameters (no. -
Page 11: 8: Activating Scenes
#8: Activating scenes Activating scenes: The KeyFob can activate scenes in the Z-Wave controller by sending scene ID and attribute of a specific action using Central Scene Com- mand Class. By default scenes are activated after single clicking or pressing and holding any of the buttons and sequences. -
Page 12: 9: Battery
#9: Battery The KeyFob can be powered with CR2450 (included) battery. Estimat- CAUTION ed battery life with device added once, default settings, direct range Using batteries other and maximum 5 pushes per day is 2 years. than specified may result in explosion. Checking battery level: Dispose of properly, observing... -
Page 13: 10: Associations
#10: Associations Association (linking devices) - direct control of other devices within NOTE the Z-Wave system network e.g. Dimmer, Relay Switch, Roller Shutter or scene (may be controlled only through a Z-Wave controller). Association ensures direct transfer control commands between devices, is The device provides the association of thirteen groups: performed without... - Page 14 The KeyFob in 2nd to 13th group allows to control 5 de- vices (regular multichannel) association group. “LifeLine” group is reserved solely for the controller and hence only 1 node can be assigned. It is not recommended to associate more than 10 devices in general, as the response time to control commands depends on the number of associated devices.
-
Page 15: 11: Advanced Parameters
#11: Advanced parameters The KeyFob allows to customize its operation to user’s needs. The set- NOTE tings are available in the FIBARO interface as simple options that may be chosen by selecting the appropriate box. Entering invalid value of parameter will re-... - Page 16 4. Second scene sequence This parameter allows to set up sequence that activates scene with ID 8. See "Sequences" on page 10 for more information. Available settings: 0 - 2nd sequence disabled 9-28086 - value of sequence Default setting: Parameter size: 2 [bytes] 5.
- Page 17 10. Single button associations - operating mode This parameter allows to choose operating mode for single button associations. Available settings: 0 - single click switches state to opposite 1 - single click switches state to opposite, dou- ble click sets to maximum level 2 - single click turns on, double click turns off 0 (switch) 1 [byte]...
- Page 18 19. Paired buttons association for This parameter allows to activate paired buttons association mode buttons. Paired buttons are dependent and association are sent only to groups. turns devices on and increases value, turns them off and decreases value. Available settings: 0 - paired buttons association inactive 1 - paired buttons association active Default setting: 0 (inactive)
-
Page 19: 12: Specifications
#12: Specifications Power supply: CR2450 3.0V battery (included) CAUTION Using batteries other Battery life: est. 2 years (default settings, max. 5 than specified may pushes per day and direct range) result in explosion. Dispose of properly, Operating temperature: 10 - 40°C observing environ- mental... -
Page 20: 13: Regulations
All information, including, but not limited to, information regarding the features, functionality, and/or other product specification are subject to change without notice. Fibaro reserves all rights to revise or update its products, software, or documentation without any obligation to no- tify any individual or entity. - Page 21 第十二條 經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用 者均不得擅自變更頻率、加大功率或變更原設計之特性及功能。 第十四條 低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現 有干擾現象時，應立即停用，並改善至無干擾時方得繼續使用。 前項合法通信，指依電信法規定作業之無線電通信。 低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性 電機設備之干擾。 Declaration of conformity hereby, Fibar Group S.A. declares that FIBARO KeyFob is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. REGULATIOnS...