1. Manuals
  2. Brands
  3. FIBARO Manuals
  4. Home Automation
  5. FGWPA-111
  6. Operating manual

FIBARO FGWPA-111 Operating Manual

Wall plug
Hide thumbs Also See for FGWPA-111:
Table of Contents

Advertisement

Quick Links

Download this manual
CONTENTS
O P E R A T I N G
M A N U A L
FIBARO WALL PLUG
Type A
FGWPA-111
3
4
5
6
7
9
EN
v1.1
10
11
12
14
20
21

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the FGWPA-111 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for FIBARO FGWPA-111

Summary of Contents for FIBARO FGWPA-111

  • Page 1: Table Of Contents

    O P E R A T I N G M A N U A L FIBARO WALL PLUG Type A FGWPA-111 CONTENTS v1.1 #1: Description and features #7: Association #2: Basic activation #8: Z-Wave range test #3: Adding the device...
  • Page 2 General information about the System FIBARO is a wireless smart home automation system, based on the Z-Wave protocol. All available devices can be controlled through a computer (PC or Mac), smartphone or tablet. Z-Wave devices are not only receivers, but can also repeat the signal, increasing the Z-Wave network range.

  • Page 3: 1: Description And Features

    #1: Description and features FIBARO Wall Plug is a remotely controlled plug-in switch with the ability to measure power and energy consumption. It uses a LED frame to visualize the current load and operating mode with color changing illumination. Our smart plug makes it possible to control electrical devices in a convenient and maintenance-free way.

  • Page 4: 2: Basic Activation

    #2: Basic activation 1. Plug the device into a socket near the main Z-Wave controller. NOTE 2. Set the main controller in the add mode (Security/non-Security When powered, the Mode). See the controller manual. device indicates the Z-Wave status with 3.

  • Page 5: 3: Adding The Device

    #3: Adding the device Adding (Inclusion) - Z-Wave device learning mode, which enables adding the device to the existing Z-Wave network. To add the device to the Z-Wave network: 1. Plug the device into a socket near the main Z-Wave controller. 2.

  • Page 6: 4: Removing The Device

    #4: Removing the device Removing (Exclusion) - Z-Wave device learning mode, which en- NOTE ables removing the device from the existing Z-Wave network. Removing Wall To remove the device from the Z-Wave network: Plug from the Z-Wave network restores all 1.

  • Page 7: 5: Operating The Device

    #5: Operating the device Controlling Wall Plug using the button: CAUTION The Wall Plug has a button, enabling the use of menu and perfor- To avoid risk of elec- mance of the following actions: trical shock, don’t 1 x click: turn the controlled device On/OFF, confirm the selected operate the device menu option (if menu is active) with wet or moist...
  • Page 8 Hardware fault state – error in communication with radio chip, NOTE device secured, unplug the device and plug it back into the Disabling socket. frame indications also Disabling visual indicator: affects alarm signal- ization. visual indication frame may be turned off for status signaling (turned On/OFF, power consumption).

  • Page 9: 6: Power And Energy Consumption

    #6: Power and energy consumption The Wall Plug enables monitoring the active power and energy con- sumption. Data is sent to the main Z-Wave controller. Measuring is carried out by the most advanced micro-controller technology, assuring the maximum accuracy and precision (+/- 1% for loads greater than 5 W).

  • Page 10: 7: Association

    #7: Association Association (linking devices) – enables the direct control of oth- NOTE er devices within the Z-Wave system network e.g. Dimmer, Re- lay Switch, Roller Shutter or scene (can be controlled only with a Association ensures direct transfer of con- Z-Wave controller).

  • Page 11: 8: Z-Wave Range Test

    #8: Z-Wave range test The Wall Plug has a built in Z-Wave network main controller range CAUTION tester. To enable the Z-Wave range test, the device must be added to the To test the main controller range: Z-Wave controller. Testing can stress the 1.

  • Page 12: 9: Z-Wave Specification

    #9: Z-Wave specification Generic Device Class: GEnERIC_TyPE_SWITCh_BInARy Specific Device Class: SPECIFIC_TyPE_POWER_SWITCh_BI- nARy Description: represents the main A type socket, enables turining the connected device On or OFF and measure its active power and energy consumption. Supported Command Classes: Command Class version Secure ZWAvEPLuS_InFO [0x5E]...
  • Page 13 Notification Command Class: The device uses notification Command Class to report different events to the controller (“Lifeline” group). notification Event Event Parameters Type Over-load detected [0x08] Power Management Over-current detected [0x08] [0x06] System System hardware Failure Device overheat [0x09] [0x03] [0x01] Protection CC: Protection Command Class prevents local or remote control of the...

  • Page 14: 10: Advanced Parameters

    #10: Advanced parameters The Wall Plug operation can be customised to user needs. The NOTE settings are available in the FIBARO interface as simple options that Entering invalid value can be chosen by selecting the appropriate box. of parameter results...
  • Page 15 ports in the Z-Wave controller. NOTE The Wall Plug reports the power load with specified frequency. The Parameter 11 isn't configuration parameters described below help specify how fre- relevant for loads un- quently the power load is reported. der 5 W. 11.
  • Page 16 Default setting: Parameter size: 1 [byte] „ON/OFF” ASSOCIATION GROUPS 21. UP value – ON/OFF (Power) association group (3) upper power threshold, which is used in parameter 23. uP value can't be lower than the value specified in parameter 22. Available settings: 100-18000 (10.0-1800.0 W, step 0.1 W) Default setting: 500 (50 W) Parameter size:...
  • Page 17 Available settings: 0-99 or 255 Default setting: Parameter size: 2 [bytes] 26. THRESHOLD UP value – ON/OFF (Power) association group (3) The value of BASIC SET command frame sent to the devices asso- ciated in the 3 group ON/OFF (Power) if power exceeds value of parameter 21.
  • Page 18 Available settings: 0 – no reaction NOTE 1 – turn connected device on you can cancel the alarm pressing 2 – turn connected device off and holding the but- 5-50 (0.5-5.0 s, step 0.1 s) – cyclically change ton. the device state with set period 1 [byte] Default setting: Parameter size:...
  • Page 19 42. LED frame color when controlled device is OFF This parameter defines the LED frame light color after turning off. Available settings: 0 – LED frame light turned off 1 – LED frame is illuminated with a color cor- responding to the last measured power, be- fore the controlled device was turned off 3 –...

  • Page 20: 11: Specifications

    #11: Specifications Power supply: 100-120 v AC, 50/60 hz Rated load Resistive loads: 15 A (continuous load): Incandescent loads: 8 A Inductive general purpose (cosφ = 0.75-0.8): 15 A Pilot duty (cosφ < 0.35): 360 VA Motor: 373 W Electronic ballasts: 3 A Rated impulse voltage: 1.5 kv Maximum inrush current:...

  • Page 21: 12: Regulations

    Directive 2014/53/Eu. The full text of the Eu declaration of conformity is available at the following internet address: www.manuals.fibaro.com WEEE Directive Compliance: Device labelled with this symbol should not be disposed with other household wastes.

Table of Contents