Service Function Table ( Fax Supported Models Only ) - Panasonic KX-MB2230JT Service Manual

11.1.4. Service Function Table ( Fax supported models only )

Code Function
501 Pause time set
503 Dial speed select
507 V34 transmission start speed
508 V34 reception start speed
514 Bell signal detect time
520 CED frequency select
521 International mode select
522 Auto standby select
523 Receive equalizer select
524 Transmission equalizer select
527 V.8 function select
552 DTMF signal tone test
553 Monitor on
select
554 Modem test
565 Irregular data set
567 T0 timer
570 BREAK% select
573 Remote turn-on ring number set
574 Dial tone detect check
590 FAX auto redial time set
591 FAX auto redial line disconnection
time set
592 CNG transmit select
Set Value
X 100msec
1: 10pps
2: 20pps
0: Disable
1: 33.6
2: 31.2
3: 28.8
4: 26.4
5: 24.0
6: 21.6
7: 19.2
8: 16.8
0: Disable
1: 33.6
2: 31.2
3: 28.8
4: 26.4
5: 24.0
6: 21.6
7: 19.2
8: 16.8
X 100msec
1: 2,100Hz
2: 1,100Hz
1: ON
2: OFF
1: ON
2: OFF
1: 0km
2: 1.8km
3: 3.6km
4: 7.2km
1: 0km
2: 1.8km
3: 3.6km
4: 7.2km
1: OFF
2: ON
1: ON
2: OFF
FAX communication 1: OFF
2: Phase B
3: ALL
1: Non-Delete
e
2: Delete
X sec
1: 61%
2: 67%
3: 63%
X number of
rings
1: ON
2: OFF
X number of
times
X sec
1: OFF
2: ALL
3: AUTO
KX-MB2230JT/ KX-MB2270JT/ KX-MB2515JT/ KX-MB2545JT/ KX-MB2575JT/ DP-MB310JT
Effective Default
Range
001~600 030 ----------
1, 2 1 ----------
0~8 1 If the code 527 is set at 2, the code 507 and 508
work.
0~8 1 If the code 527 is set at 2, the code 507 and 508
work.
1~9 3 ----------
1, 2 1 See How To Output The Journal Report (P.213).
1, 2 1 See How To Output The Journal Report (P.213).
1, 2 1 The resolution reverts to the default when transmis-
sion is complete.
1~4 1 Set RX equalizer to automatic mode.
1~4 1
1, 2 2
1, 2 2 See Test Functions (P.124).
1~3 1 Sets whether to monitor the line signal with the
unit's speaker during FAX communication or not.
See Test Functions (P.124).
1,2 1 Sets whether delete Caller ID irregular data or not .
001~255 052 Sets a higher value when the response from the
other party needs more time during automatic FAX
transmission.
1, 2, 3 1 Sets the% break of pulse dialing according PBX.
00~99 10 Sets the number of rings before the unit starts to
operate TAM in the TEL mode.
1, 2 2 ----------
00~99 05 Selects the number of redial times during FAX com-
munication (not including the first dial).
001~999 065 Sets the FAX redial interval during FAX communi-
cation.
1~3 2 Lets you select the CNG output during FAX trans-
mission. ALL: CNG is output at phase A. AUTO:
CNG is output only when automatic dialing is per-
formed. OFF: CNG is not output at phase A. Refer
to Sometime There is a Transmit Problem
(P.206).
131
Remarks