Test Mode; Test Functions - Panasonic KX-MB2230JT Service Manual

KX-MB2230JT/ KX-MB2270JT/ KX-MB2515JT/ KX-MB2545JT/ KX-MB2575JT/ DP-MB310JT

10 Test Mode

10.1. Test Functions

The codes listed below can be used to perform simple checks of some of the unit's functions. When complaints are received
from customers, they provide an effective tool for identifying the locations and causes of malfunctions.
Test Mode Type of Mode
MEMORY CLEAR Service Mode
MOTOR TEST Service Mode
MODEM TEST Service Mode
( Fax supported mod-
els only )
ROM CHECK Service Mode
LCD TEST Service Mode
DTMF SINGLE Service Mode
TONE TEST
( Fax supported mod-
els only )
LED TEST Service Mode
KEY TEST Service Mode
SCANNER TEST Service Mode
LSU TEST Service Mode
High Voltage Power Service Mode
Supply Board
CHECK
FAN TEST Service Mode
MEMORY CLEAR Service Mode
(except History data)
PRINT TEST PAT- Service Mode
TERN
Code
Operation after code
input
"5" "5" "0" Clear the memory where the users can store data.
SET
"5" "5" "6" 00:printer motor feed 10:auto document feed 20:carriage
SET
"5" "5" "4" Telephone line circuit is connected automatically, output the following signals on
the circuit line.
SET
1) OFF
8) INFO0c 9) INFO0a 10) ToneB 11) ToneA 12) Lprob 13) CCH Org
14) CCH Ans 15)V21 300bps 16) V27 2,400bps 17) V27 4,800bps
18) V29 7,200bps
22) V17 12,000bps 23) V17 14,400bps 24) V34 2,400bps 25) V34 4,800bps
26) V34 7,200bps 27) V34 9,600bps 28) V34 12,000bps 29) V34 14,400bps
30) V34 16,800bps 31) V34 19,200bps 32) V34 21,600bps
33) V34 24,000bps 34) V34 26,400bps 35) V34 28,800bps
36) V34 31,200bps 37) V34 33,600bps
"5" "5" "1" Indicates the version and checks the sum of the ROM.
SET
"5" "5" "8" Checks the LCD indication.
Illuminates all the dots to check if they are normal.
SET
"5" "5" "2" Outputs the DTMF as single tones. Used to check the frequencies of the individ-
ual DTMF tones. Refer to DTMF Single Tone Transmit Selection (P.125).
1....ON
2....OFF
"5" "5" "7" All LEDs above the operation panel board flash on and off, or are illuminated.
"5" "6" "1" Checks the button operation.
Indicates the button code on the LCD while the button is pressed.
START (any key)
Refer to Button Code Table (KX-MB2230/KX-MB2545 ONLY) or Button Code
Table (KX-MB2270/KX-MB2575 ONLY) (P.126).
"5" "5" "5"
LED lights up, Scanner scanning.
1:RED / 2:GREEN / 3:BLUE / 4:monochrome / 5:Color
"6" "3" "9" Laser radiates, Polygon rotates
SET
"6" "2" "8"
SET
"6" "7" "7" 01:TEST OFF
02:FAN 1 High-speed rotation
03:FAN 1 Low-speed rotation
04:FAN 1 STOP
"7" "1" "0" Refer to Memory Clear Specification (P.133).
SET
"8" "5" "2" 1. Press "852" then the SET key in the service mode.
2. As "PATNO. =" is displayed on the LCD, enter the test pattern No. and press
the SET key.
3. When "NO. = "is displayed on the LCD, enter the printing number and press the
SET key. (Press "00" for the infinite printing.)
4. "MODE=" is displayed on the LCD. Press "0" to start printing or press "1" to go
to the next screen.
5. When "1" is pressed at MODE, "INTVL = "is displayed on the LCD. Enter the
printing interval (000~999 sec).
6. The printing repeats the designated number of times at the programmed print-
ing intervals.
Refer to Print Test Pattern (P.128).
124
Function
2) 1,100Hz 3) 2,100Hz 4) ANSam 5) CI 6) CM 7) JM
19) V29 9,600bps 20) V17 7,200bps 21) V17 9,600bps