Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Commell LV-602
Summary of Contents for Commell LV-602
- Page 1 LV-602 Mini-ITX Motherboard User’s Manual 1.1 2005/3/18...
- Page 2 LV-602 User’s Manual Copyright Copyright 2004 - 2005. All rights reserved. This document is copyrighted and all rights are reserved. The information in this document is subject to change without prior notice to make improvements to the products. This document contains proprietary information and protected by copyright. No part of this document may be reproduced, copied, or translated in any form or any means without prior written permission of the manufacturer.
-
Page 3: Packing List
LV-602 User’s Manual Packing List: Please check the package before you starting setup the system Hardware: LV-602 series motherboard x 1 Cable Kit: 40-pin ATA100 IDE Flat Cable ..........34-pin Floppy Cable .............. Dual-USB Port Cable ............DB9 COM Port Cable ............ - Page 4 LV-602 User’s Manual Index Chapter 1 <Introduction> ..................5 <Product Overview>................5 1.2 <Specification>..................6 1.3 <Component Placement> ................ 8 Chapter 2 <Hardware Setup>................9 2.1 <Connector Location>................9 2.2 <Jumper Reference> ................10 2.3 <Connector Reference>................. 11 2.3.1 <Internal Connector>..............11 2.3.2 <External Connector>..............
-
Page 5: Chapter 1
PRO/100+ LAN, USB 1.1, IEEE 1394, AC’97 3D audio and TV-out interfaces. Compact Mini-ITX Form Factor @ 170 x 170 mm LV-602 is based on the ultra compact Mini-ITX form factor at only 170 x 170 mm of dimension, meets the demand of compact and powerful computing platform. With this feature, LV-602 should be the ideal solution for the high-end, Pentium III level book-size, slim type and other embedded PC systems. -
Page 6: Specification
LV-602 User’s Manual Introduction 1.2 <Specification> General Specification Form Factor Mini-ITX motherboard Intel Pentium III / Celeron / VIA C3 processors Package: FC-PGA370 FSB: 100/133MHz Memory 2 x 168-pin PC133 DIMM up to 1GB Unbufferred, none-ECC memory supported only Chipset... - Page 7 LV-602 User’s Manual Introduction Audio Codec VIA VT1612A Output Interface Line-in, line-out, MIC-in and CD-in Connectors Onboard 5-pin header for line-out, 5-pin for line-in and MIC-in, 4-pin header for CD-in External Line-out and MIC-in jack IEEE1394 Controller AGERE FW323 PCI IEEE1394 controller...
-
Page 8: Component Placement
LV-602 User’s Manual Introduction 1.3 <Component Placement> VIA VT1612A IEEE1394a REALTEK 8139C+ Socket370 BIOS VIA VT686B (Southbridge) VIA PL133 (Northbridge) Component Placement... -
Page 9: Chapter 2
LV-602 User’s Manual Hardware Setup Chapter 2 <Hardware Setup> This chapter contains the information for installation of hardware. The install procedure includes jumper settings, CPU and memory installation, fan, I/O and panel connections. 2.1 <Connector Location> JP5 JP3 PCI1 IDE0 IDE1... -
Page 10: Jumper Reference
LV-602 User’s Manual Hardware Setup 2.2 <Jumper Reference> Jumper Function CMOS Operating/Clear Setting JP15 IDE1 Pin-20 voltage setting CPU FSB setting JP15 Jumper Reference... -
Page 11: Connector Reference
LV-602 User’s Manual Hardware Setup 2.3 <Connector Reference> 2.3.1 <Internal Connector> Connector Function Remark PGA370 PGA370 CPU socket Standard ATX power connector Standard JWR1 DIMM1~2 DIMM module sockets Standard PCI connector Standard PCI1 IDE0 IDE connector Standard IDE1 IDE connector... -
Page 12: Cpu And Memory Setup
LV-602 User’s Manual Hardware Setup 2.4 <CPU and Memory Setup> 2.4.1 <CPU Setup> The board supports Intel Pentium III / Celeron and VIA C3 processors, and supports 66/100/133MHz of front side bus. The jumper J18 can let you configure the font side bus as 100MHz or 133MHz. -
Page 13: Memory Setup
LV-602 User’s Manual Hardware Setup 2.4.2 <Memory Setup> The board supports two 168-pin SDRAM up to 1GB as following table: DIMM1 DIMM2 CPU and Memory Setup... -
Page 14: Cmos Setup
LV-602 User’s Manual Hardware Setup 2.5 <CMOS Setup> The board’s data of CMOS can be setting in BIOS. If the board refuses to boot due to inappropriate CMOS settings, here is how to proceed to clear (reset) the CMOS to its default values. -
Page 15: Ide Interface
LV-602 User’s Manual Hardware Setup 2.6 <IDE Interface> The board provides UltraDMA100 IDE interface to support up to 4 ATAPI devices. The jumper JP15 can enable IDE1 to support 5V power on 20 pin. Jumper: JDOM Type: onboard 3-pin header... -
Page 16: Floppy Port
LV-602 User’s Manual Hardware Setup 2.7 <Floppy Port> The board provides one floppy connector to support up to 2 floppy drives. 2.8 <LAN Port> The board provides one PCI based Ethernet Controller with REAKTEK 8139C+, support 10/100Mbps of transfer rate and compliance with IEEE802.3. The connector J16 provides external LAN LED for front panel. -
Page 17: Audio
LV-602 User’s Manual Hardware Setup 2.9 <Audio > The board provides onboard AC97 audio with VIA VT1612A for stereo sound, with Line-in, Line-out and MIC-in interfaces. JP3 (Line-out) JP7 (CDIN) JP5 (MIC-in & Line-in) Audio... -
Page 18: Usb And Ieee1394 Interface
LV-602 User’s Manual Hardware Setup 2.10 <USB and IEEE1394 Interface> The board integrates onboard USB1.1 interface with VIA VT686B, and it also provides IEEE1394a interface with AGERE FW323-05. Connector: J15 Type: 10-pin (5 x 2) header for USB3/4 Ports (pitch = 2.54mm) -
Page 19: Serial Port
LV-602 User’s Manual Hardware Setup 2.11 <Serial Port> The board provides two RS232 serial ports with one external DB9 connector and one onboard 10-pin header. Connector: JP6 Type: 10-pin (5 x 2) header for COM2 (pitch = 2.54mm) Description Description... -
Page 20: Amr And Dvo Interface
LV-602 User’s Manual Hardware Setup 2.12 <AMR and DVO Interface> The AMR headers Supports the Audio and modem function. The board also provides one 26-pin header enable you to connect a Digital Video Output device on the digital video port. -
Page 21: Switch And Indicator
LV-602 User’s Manual Hardware Setup 2.13 <Switch and Indicator> The JP9 provides front control panel of the board, such as power button, reset and beeper, etc. Please check well before you connecting the cables on the chassis. Connector: JP9 Type: onboard 14-pin (2 x 7) 2.54-pitch header... -
Page 22: Chapter 3
LV-602 User’s Manual BIOS Setup Chapter 3 <BIOS Setup> The motherboard uses the Award BIOS for the system configuration. The Award BIOS in the single board computer is a customized version of the industrial standard BIOS for IBM PC AT-compatible computers. It supports Intel x86 and compatible CPU architecture based processors and computers. -
Page 23: Chapter 4
LV-602 User’s Manual Flash BIOS Chapter 4 <Flash BIOS> 4.1 BIOS Auto Flash Tool The board is based on Award BIOS and can be updated easily by the BIOS auto flash tool. You can download the tool online at the address below: http://www.award.com... -
Page 24: Contact Information
Taiwan Commate Computer Inc. Address 8F, No. 94, Sec. 1, Shin Tai Wu Rd., Shi Chih Taipei Hsien, Taiwan +886-2-26963909 +886-2-26963911 Website http://www.commell.com.tw E-Mail info@commell.com.tw (General Information) tech@commell.com.tw (Technical Support) Commell is our trademark of industrial PC division Contact Information...
Need help?
Do you have a question about the LV-602 and is the answer not in the manual?
Questions and answers