Siemens EX875LX34E Instruction Manual page 29

Notes
Always cook with the lid on. Exception: "Frying with a
■
large amount of oil in the saucepan", temperature
setting 5/170 °C.
If an audible signal does not sound, make sure that
■
the lid is on the pan.
Never leave oil unattended during heating. Use oil or
■
fat that is suitable for frying. Do not mix different
cooking fats together, e.g. oil and lard. Mixtures of
different fats may froth up when hot.
If you are not satisfied with the cooking result, e.g.
■
when cooking potatoes, next time use less water but
keep the recommended temperature setting.
Setting the boiling point
The point at which water starts to boil depends on the
height of your home above sea level. You can set the
boiling point if water is boiling too strongly or not
strongly enough. To do this, proceed as follows:
Select the basic setting
■
~ "Basic settings"
The basic setting is 3 as standard. If your home is
■
between 200 and 400 metres above sea level, there
is no need to set the boiling point. If not, choose the
correct setting from the following table according to
your altitude:
Height
0 - 100 m.
100 - 200 m.
200 - 400 m.
400 - 600 m.
600 - 800 m.
800 - 1000 m.
1000 - 1200 m.
1200 - 1400 m.
Above 1400 m.
* Basic setting
Temperature setting 3/100 °C provides efficient
Note:
cooking even if the water does not bubble very strongly
during the heating process. However, if you are not
satisfied with the boiling result, you can change the
boiling point setting.
Connecting the wireless temperature sensor to the
control panel
You will need to connect the wireless temperature
sensor to the control panel before using the cooking
functions for the first time.
To connect the wireless temperature sensor to the
control panel, follow the instructions below:
Select the basic setting
1.
~ "Basic settings"
The indicator for one of the hotplates and the
indicator will light up. The control panels switch off.
Select the hotplate and its indicator will light up. A
2.
signal will sound. The
; see the section on
™...
Setting ™...
‚
ƒ
„ *
...
†
‡
ˆ
‰
Š
; see the section on
™‚...
indicator will flash.
õ
Press the
3.
sensor within 30 seconds.
After a few seconds, the status of the connection
between the temperature sensor and the control
panel will appear on the hotplate's display.
Status
Connected correctly
‹
Not connected correctly: Transmission error.
‚
Not connected correctly: Temperature sensor fault.
ƒ
The cooking functions are made available once the
■
temperature sensor has been connected to the
control panel correctly.
If there is a fault with the temperature sensor, the
■
connection may not be established correctly for the
following reasons:
– Bluetooth communication error.
– You did not press the symbol on the temperature
sensor within 30 seconds of selecting a hotplate.
– The battery in the temperature sensor has run
out.
Reset the wireless temperature sensor and follow
the connection procedure once again.
If the temperature sensor and the control panel are
■
not connected correctly due to a transmission error,
follow the connection procedure once again.
If the display continues to show incorrect connection
, contact our technical after-sales service.
‚
Resetting the wireless temperature sensor
Touch and hold the
1.
10 seconds.
While you are doing this, the temperature sensor's
LED indicator will light up three times. When the LED
lights up for the third time, it will start to reset the
temperature sensor. At this point, you will need to lift
your finger off the symbol.
Once the LED goes out, this means that the wireless
temperature sensor has been reset.
Repeat the connection procedure from point 2.
2.
b
Cooking assist functions
symbol on the wireless temperature
»
symbol for approximately 8-
»
en
29