Monitor Out L/R; Odd Channel/Even Channel Crosstalk; Maximum Output; Gain - Yamaha O1V 96 Service Manual

01V96
t Odd channel/even channel crosstalk
Input frequency Output level (odd channels) Permitted range (even channels)
1kHz
The even channels must be the same too.
y Maximum output (OMNI OUT 1~4)
Input frequency Permissible range Permissible range (
1kHz +24±0.5dBu

2-4. MONITOR OUT L/R

Parameters
q Gain (both L/R)
Input frequency Input level
1kHz +4dBu
w f characteristic (both L/R)
Parameter
Input frequency
20Hz
40kHz
e Residual noise (both L/R)
Parameter
MONITOR LEVEL
MAX
MIN
r L/R level difference
The range for the difference in the gain measured
with q is regulated as follows.
Permitted range
Within 1dB
t Crosstalk between left and right
Parameter
Input frequency Output level (L) Permitted range (R)
1kHz
The right side must be the same.
y Maximum output (both L/R)
Input frequency Permissible range Permissible range (
1kHz +24±0.5dBu
2-5. PHONES OUT L/R
Parameters
78
Downloaded from www.Manualslib.com
+22dBu -58dBu or below
distortion ratio
0.01% or below
Must be input from CH1 (XLR).
Set the MONITOR/2TR lN SW to
MONITOR.
Set the MONITOR OUT LEVEL to
MAX.
Regulated output level Permitted range
+4dBu +4±2dBu
The permitted range uses 1 kHz as
the reference.
Input level Permitted range
+4dBu -1.5~+0.5dB
+4dBu -1.5~+0.5dB
Switch STEREO OUT Off.
Permitted range
-86dBu or below
-100dBu or below
PAN L swung to cut off.
+22dBu -58dBu or below
distortion ratio
0.01% or below
Must be input from CH1 (XLR).
Set the MONITOR/2TR lN SW to
MONITOR.
Set the PHONES LEVEL to MAX.
manuals search engine
q Gain (both L/R)
Input frequency Input level
1kHz +4dBu
w f characteristic (both L/R)
Parameter
Input frequency
)
20Hz
40kHz
e Residual noise (both L/R)
Parameter
Permitted range
-110dBu or below
r L/R level difference
The range for the difference in the gain measured
with q is regulated as follows.
Permitted range
Within 1dB
t Maximum output (both L/R)
Parameter
Input frequency Permissible range Permissible range (
1kHz -4.8±0.5dBu
y Crosstalk between left and right
Parameter
Input frequency Output level (L) Permitted range (R)
1kHz
The right side must be the same.
2-6. 2TR IN ANALOG L/R
Parameters
q Gain (both L/R)
Input frequency Input level
1kHz -10dBV
)
w f characteristic (both L/R)
Parameter
Input frequency
20Hz
40kHz
Regulated output level Permitted range
-12.8dBu -12.8±2dBu
The permitted range uses 1 kHz as
the reference.
Input level Permitted range
+4dBu -3~0.5dB
+4dBu -3~0.5dB
Set the PHONES LEVEL to MIN.
-12 dB must be output from the internal
oscillator.
distortion ratio
0.04% or below
PAN L swung to cut off.
-10dBu -75dBu or below
Inspect with MONITOR OUT .
Set the MONITOR OUT LEVEL to MAX.
Set the 15/16 GAIN to MIN.
Gain only can also be inspected with
STEREO OUT.
Set the MONITOR/2TR IN SW to 2TR
IN.
Set the 15/16/2TR IN SW to 2TR IN.
Regulated output level Permitted range
+4dBu +4±2dBu
The permitted range uses 1 kHz as
the reference.
Input level Permitted range
-10dBV -1.5~0.5dB
-10dBV -1.5~0.5dB
)