Special Functions - Mandik KFR-09GW/BP User Manual

16

Special functions

EN
Refrigerant Leakage Detection
With this new technology, the dipsplay area will appear EC and the indication lamps continue flashing when the outdoor unit
detects refrigerant leakage
Louver Angle Memory Function (optional):
Within the scope of safety angle, it will memorize the open angle of horizontal louver If it exceeds, it will memorize the boundry
of safety angle In the following circumstances, it will return to standard angle: 1) pressing the manual switch, 2) unplug and then
plug in the machine So we strongly suggest that the open angle of the horizontal louver should not be set too small, in case the
condensed water forms and drops from the horizontal louver
SELF CLEAN function (Optional)
Function used after the Shut Down of cooling operation to clean the Evaporator and keep it as fresh for the next operation
„ „
The unit will operate as following sequence: FAN ONLy mode at Low fan speed--Heating operation with LOW fan speed(appli-
„ „
cable to cooling & heating modles only) ---FAN ONLy operation--Stop Operation---Turn off
NOTE:
This function is only available under COOL(AUTO COOL, FORCED COOL) and DRY mode.
„ „
Before select the function, it is recommended to run the air conditioner under Cooling operation for about half an hour. Once the Self
„ „
Clean function is activated, all TIMER setting will be cancelled.
During Self Clean operation, when press the SELF CLEAN button on the remote controller again will stop the operation and turn off
„ „
the unit automatically.0
CLEAN AIR function (on some models)
Improving the quality of indoor air is one of the purposes of an air conditioner This air conditioner is equipped with ionizer or
Plasma Dust Collector(Depending on specific configuration of the model) With the anions generated by Ionizer, the air circulation
of the air conditioner fills the room with refreshing, natural and healthy air The Plasma Dust Collector generates a high voltage
ionization zone, through which the air is converted to plasma Inside the air most of the dust, smoke, and pollen particles are cap-
tured by the electrostatic filter
Anti-mildew function (Optional)
When turns off the unit on COOL, DRy, AUTO (Cool) mode, the air conditioner will continue operating for about 7–10 minutes
„ „
(depending on models) at LOW fan speed If turns off on HEAT mode, the unit will continue operating for about 30 seconds
at LOW fan speed This will help to dry up the condensed water inside the evaporator, and prevent the breeding of mildew
Under Anti-mildew operation, do not restart the air conditioner until the unit is completely off
„ „
NOTE:
This manual does not include Remote Controller Operations, see the
<<Remote Controller Instruction>> packed with the unit for details.
Operating temperature
Temperature
Room temperature
Outdoor temperature
NOTE:
1. Optimum performance will be achieved within these operating temperatures. If air conditioner is used outside of the above condi-
tions, certain safety protection features might come into operation and cause the unit to function abnormally.
2. If the air conditioner runs for a long time in cooling mode and the humidity is high (over 80 %) , condensed water may drip out of the
unit. Please sets the vertical air flow louver to its maximum angle (vertically to the floor), and set HIGH fan mode.
Suggestion: For the unit adopts an Electric Heater, when the outside ambient temperature is below 0 o C(32 o F), we strongly
recommend you to keep the machine plugged in order to guarantee it running smoothly
Mode
Cooling operation
17 o C ~ 32 o C
(62 o F ~ 90 o F)
0 o C ~ 50 o C
(32 o F ~ 122 o F)
-15 o C ~ 50 o C / 5 o F ~ 122 o F:
For the models with low
temperature cooling system
Heating operation
0 o C ~ 30 o C
(32 o F ~ 86 o F)
-15 o C ~ 30 o C
(8 o F ~ 86 o F)
Drying operation
10 o C ~ 32 o C
(50 o F ~ 90 o F)
0 o C ~ 50 o C
(32 o F ~ 122 o F)