Download Print this page
Lutron Electronics CASETA WIRELESS ELK-M1XSLC Instructions Manual

Lutron Electronics CASETA WIRELESS ELK-M1XSLC Instructions Manual

Wireless communication interface

Advertisement

Quick Links

ELK-M1XSLC
M1 Interface kit for Lutron
Homeworks QS or Caséta Line
APPLICATION:
The ELK-M1XSLC Interface Kit has been enhanced
to support Lutron's Homeworks and Caséta products.
Interfacing M1 Control to Lutron allows intelligent control
of devices in response to security system actions or
conditions. The most typical integration devices supported
are:Lights, Shades, and Keypad controllers. The level
of integration is dependent on which type and model of
Lutron devices being implemented.
ELK-M1XSLU SPECIFICATIONS:
Connects to the ELK-M1 Keypad Databus
Addressable as a TYPE 5 Databus (ID 1-7)
Operating Voltage: 12 Volts DC Supplied from M1
Current Draw: 31mA
Activity/Status LED (Orange)
Auto-Reset Hardware Watchdog Circuit
Housing Dimensions: 4.25" x 6.375" x 2.125"
Circuit Board: 2.75" x 3.95"
Connects to IP232 via RS232 and null modem (Incl.)
Connects to M1 via 4 screw terminals
ELK-IP232 SPECIFICATIONS:
• Converts RS232 Serial to IP for connection to the IP
port on Lutron's QS or Smartbridge Pro Interfaces
• LED Indicators for Power, Link, and Data
• Operating Voltage: 12 Volts D.C.
Supplied from ELK-P1216 Power Supply (Incl)
• Current Draw: 135 mA
• Dimensions: 3.85" L x 1.7" W x 0.93" D
 2017 Elk Products Inc. All rights reserved.
Lutron, Homeworks, QS, Caséta Wireless, and Smartbridge Pro are
registered trademarks of Lutron Electronics Co., Inc.
828-397-4200 828-397-4415 Fax
L659 Rev. B 1/25/2016
PO Box 100
3266 US Hwy 70 West
Hildebran, NC 28637
http://www.elkproducts.com
CASÉTA
INSTRUCTIONS
Specifications are Subject to Change without notice.
NOTICE: Drawings, illustrations, diagrams, part numbers, etc. are provid-
ed as reference only and are based on equipment available at the time
the information was created. All information contained in this document
are subject to change without notice.
The extent of integration between Elk Products and Partner Mfgs varies,
and there may be situations or limitations beyond Elk's control that make
certain desirable features unavailable or unusable. Partner products and/
or protocols, including Elk's may not contain the capabilities or data defi-
nitions to permit additional integration beyond what is currently available.
Partners may also, at their option, add, modify, or discontinue features or
support without notification.
NOTE: The Caséta product family offers temperature solutions using "WiFi
thermostats". These are not supported through M1. They can only be
controlled through IP using Lutron Caséta smartphone app.
For reasons stated herein, Elk Products makes no warranty that it will
be able to integrate all available features or operations, nor does it make
any express or implied warranties of fitness for a particular purpose or of
merchantability. Refer to Elk's Limited Warranty.
WIRELESS
®
Printed in USA

Advertisement

loading

Summary of Contents for Lutron Electronics CASETA WIRELESS ELK-M1XSLC

  • Page 1 Lutron, Homeworks, QS, Caséta Wireless, and Smartbridge Pro are any express or implied warranties of fitness for a particular purpose or of registered trademarks of Lutron Electronics Co., Inc. merchantability. Refer to Elk's Limited Warranty. PO Box 100...
  • Page 2 PLEASE READ THIS PAGE FIRST! LUTRON CASÉTA WIRELESS Lutron Caséta Wireless ® ® The following components will be needed to integrate Elk to Lutron Caséta Wireless. Part Number & Description ELK-M1 or M1EZ8 Control ELK-M1XSLC Kit Contents of kit: ELK-M1XSLU M1 to Lutron serial interface ELK-IP232 Serial to IP Converter (Firmware version 1.0.18 and later ***) 9 Pin Serial ribbon cable 9 Pin Null Modem adapter...
  • Page 3: Equipment Setup

    LUTRON CASÉTA WIRELESS 2 - Equipment Setup Please setup the Lutron equipment and devices and have them all working before proceeding. Turn off the power to all equipment before making any wiring connections. Wire the M1XSLU to the M1's RS485 data bus. Please follow the recommendations in the M1 Installation book and this manual for wiring the 4 conductors of the data bus (+12V, A, B, and Neg) to the terminals on the M1XSLU.
  • Page 4 LUTRON CASÉTA WIRELESS 3 - Configuring the IP232 IP Interface Download and install the IP232 Configuration PC software utility from the ELK website (www.elkproducts.com). A copy of the IP232 instructions is packed with the M1XSLC kit with steps for defaulting, resetting, or updating the IP232 firmware if needed. Be sure the IP232 is connected to the local area network and is powered by the P1216 plug-in power supply.
  • Page 5 LUTRON CASÉTA WIRELESS Verify that the Bootloader version is 1.0.7 or higher and that the Firmware version is 1.0.18 or higher. If either of these are older versions it will be mandatory to Update these. The Bootloader must be Ver. 1.07 or higher and the Firmware MUST be Ver.1.0.18 or higher in order for the ELK-IP232 to work with the Lutron Smartbridge Pro.
  • Page 6 LUTRON CASÉTA WIRELESS Login Prompt and Reply - The IP232 has the ability to make a telnet connection that is secured with a Username and Password. This is a requirement for connecting to a Lutron Smart Bridge Pro. The IP232 configuration utility allows full customization of the prompts and the responses for these security challenges.
  • Page 7 LUTRON CASÉTA WIRELESS Configuring Lutron Caséta Devices into M1 Lighting Each Caséta device is assigned a unique Integration Device ID when setup and programmed. Integration to the ELK-M1 involves mapping these Device IDs to corresponding numbered M1 Light Device locations. See Table 3. M1 Light Device locations that do not have corresponding Lutron Integration Device IDs should be left blank (unprogrammed).
  • Page 8 LUTRON CASÉTA WIRELESS Select the Lighting folder from ElkRP > Automation > Lighting to open the Lighting display setup screen. 4.10 NOTE: Leave blank any M1 Lighting Device locations that do not have a Device ID to be mapped to. Populate the Device 1(A1) row first.
  • Page 9 LUTRON CASÉTA WIRELESS 5 - Controlling Lutron Caséta Lights or Devices using Rules Select ElkRP > Automation > Rules. Click New to start a new Rule. Example: Turn ON a Flood Light whenever the System is Armed Away. Click WHENEVER > Security/Alarms > Is Armed > Armed Away. Use the drop down arrow to select an area (partition) or click OK to accept the default "Area 1".
  • Page 10 LUTRON CASÉTA WIRELESS TABLE 4: Dim & Fade Rate options for Caseta Dimmers in ElkRP Lighting Rules For Caseta Dimmers 2 thru 50 the following Dim Levels and Fade Rate options may be programmed Result Result Fade Fade Level Rate Level Rate Sets Dim level to 1%...
  • Page 11 LUTRON CASÉTA WIRELESS TABLE 5: Smartbridge Pro Scene Activations Program M1 Lighting Device #1 to the following Dim Level and Fade Rate Set to Level Fade Rate must M1 Lighting Device Name assigned to the Smartbridge Pro Scene (Dim Level) be set to “0”...
  • Page 12 M1XSLC Installation Manual - LUTRON CASÉTA WIRELESS Page 12...