Installation; Before Installing Your Insert; Chimney Speciications; Wood Insert Speciications - HAMPTON BAY HI300 Owners & Installation Manual

Hampton Inserts are constructed with the high-
est quality materials and assembled under strict
quality control procedures that insure years of
trouble free and reliable performance.
It is important that you read this manual thor-
oughly and fully understand the safe instal-
lation and operating procedures. The more
you understand the way your Hampton Insert
operates, the more enjoyment you will experi-
ence from knowing that your unit is operating
at peak performance.
BEFORE INSTALLING
YOUR INSERT
1) Please read this entire manual before
you install and use your new wood insert.
Failure to follow instructions may result
in property damage, bodily injury or even
death. Install and use only in accordance
with manufacturer's installation and operat-
ing instructions.
2) Check your local building codes - Building
Inspection Department. You may require
a permit before installing your insert. Be
aware that local codes and regulations may
override some items in the manual.
WARNING: Careless installation is the
major cause of safety hazard. Check all
local building and safety codes before
installation of unit.
3) Notify your home insurance company that
you plan to install a ireplace insert.
4) Your ireplace insert is heavy and requires
two or more people to move it safely. The
insert can be badly damaged by mishan-
dling.
5) If your existing ireplace damper control
will become inaccessible once you have
installed your Hampton Insert, you should
either remove or secure it in the open posi-
tion.
6) Inspect your ireplace and chimney prior
to installing your insert to determine that it
is free from cracks, loose mortar or other
signs of damage. If repairs are required,
they should be completed before installing
your insert. Do not remove bricks or mortar
from your masonry ireplace.
7) Do not connect the insert to a chimney
system servicing another appliance or
an air distribution duct.
Emissions from burning wood or gas could
contain chemicals known to the State of Cali-
fornia to cause cancer, birth defects or other
reproductive harm.
CHIMNEY
SPECIFICATIONS
Before installing, check and clean your chimney
system thoroughly. If in doubt about its condi-
tion, seek professional advice. Your Hampton
Insert is designed for installation into a masonry
ireplace that is constructed in accordance with
the requirements of "The Standard for Chimneys,
Fireplaces, Vents, and Solid Fuel Burning Ap-
pliance", N.F.P.A. 211, the National Building
Code of Canada, or the applicable local code
requirements.
The appliance, when installed, must be electri-
cally grounded in accordance with local codes or,
in the absence of local codes, with the National
Electrical Code, ANSI/NFPA 70, or the Canadian
Electrical code, CSA C22.1.
Hampton Inserts are designed to use either a
5.5" (140mm) or 6" (152mm) lue.
Requirements for Installing
Solid-fuel Inserts in Factory-built
Fireplaces.
1) The insert must be tested and meet the
requirements of UL 1482 (U.S.) and or ULC
S628 (Canada) when tested in a masonry
ireplace built per ULC S628.
2) The factory-built ireplace must be listed per
UL 127 or ULC S610.
3) Clearances obtained from the masonry ire-
place tests are also relevant for installation
in factory-built ireplaces.
4) Installation must include a full height listed
chimney liner type HT requirements (2100
degree F.) per UL 1777 (U.S.) or ULC
S635 (Canada). The liner must be securely
attached to the insert lue collar and the
chimney top.
5) Means must be provided to prevent room
air passage to the chimney cavity of the
ireplace. This may be accomplished by
sealing the damper area around the chimney
liner, or sealing the ireplace front.
6) Alteration of the ireplace in any manner is
not permitted with the following exceptions;
a. external trim pieces which do not afect
the operation of the ireplace may be
removed providing they can be stored
on or within the ireplace for re-assembly
if the insert is removed.
b. the chimney damper may be removed
to install the chimney liner.

installation

7) Circulating air chambers (i.e. in a steel
ireplace liner or metal heat circulator) shall
not be blocked.
8) Means must be provided for removal of the
insert to clean the chimney lue.
9) Inserts that project in front of the ireplace
must be supplied with appropriate support-
ing means.
10) Installer must mechanically attach the sup-
plied label to the inside of the irebox of the
ireplace into which the insert is installed.
"WARNING: This ireplace has been converted
for use with a wood insert only and cannot be
used for burning wood or solid fuels unless
all original parts have been replaced, and the
ireplace re-approved by the authority having
jurisdiction."
In order for a solid-fuel insert to be certiied for use
in factory-built ireplaces, the above information
must be clearly stated in the installation manual
and appropriate markings. Final approval is
contingent on the authority having jurisdiction.
WOOD INSERT
SPECIFICATIONS
Your ireplace opening requires the
following minimum sizes:
Height 21.5"
Width 25"
Depth 17.5"
Hampton HI300 Wood Cast Insert
|
7
| 7