Assembly & Adjustments; Inserting And Removing The Battery Pack From The Tool; Belt Hook And Bit Clip; Operation - Stanley POP PB3400 Instruction Manual

(see technical data). The minimum conductor size is
1.5 mm²; the maximum length is 30 m. When using
2 . 2 A S S E M B Y L &
WARNING: Prior to assembly and
adjustment, always remove the battery
pack. Always switch off the tool before
inserting or removing the battery pack.
WARNING: Use only POP® battery packs
and chargers.
2 . 3 n I e s t r n i g a n
Battery Pack from the Tool
NOTE: For best results, make sure your battery pack is
fully charged. The light will shut off without warning
when the battery is fully discharged.
TO INSTALL THE BATTERY PACK INTO THE
HANDLE
1. Align the battery pack (K) with the rails inside
2. Slide it into the handle until the battery pack is
firmly seated in the tool and ensure that it does
not disengage.
TO REMOVE THE BATTERY PACK FROM TO THE
HANDLE
1. Press battery release button and firmly pull the
battery pack out of the tool handle.
2. Insert battery pack into the charger as
described in the charger section for this
manual.
2 . 4 B e t l H o o k a n
WARNING: To reduce the risk of serious
personal injury, DO NOT suspend tool
overhead or suspend objects from the belt
hook. ONLY
WARNING: To reduce the risk of serious
personal injury, ensure the screw holding
the belt hook is secure.
IMPORTANT: When attaching or replacing the belt
hook or bit clip, use only the screw that is provided. Be
sure to securely tighten the screw. The belt hook and
bit clip can be attached to either side of the tool using
only the screw provided, to accommodate left- or
right-handed users. If the hook or bit clip is not desired
at all, it can be removed from the tool. To move belt
hook or bit clip, remove the screw that holds it in
place then reassemble on the opposite side. Be sure to
securely tighten the screw.
A D J U S T M E N T S
d R e m o v n i g h t e
d B t i l C p i
2 . 5 O P E R A T O I N
Instructions for Use
WARNING: Always observe the safety
instructions and applicable regulations.
WARNING: To reduce the risk of serious
personal injury, disconnect battery
pack before making any adjustments
or removing/installing attachments or
accessories.
2 6 P . o r p r e H a n d
WARNING: To reduce the risk of serious
personal injury, ALWAYS use proper hand
position.
WARNING: To reduce the risk of serious
personal injury, ALWAYS hold securely in
Proper hand position requires one hand on the main
handle fig. 1- (I).
2 . 7 o T o S l e u t p &
WARNING: Before adjusting tool, always
remove the battery pack.
Opening and closing the mandrel collector (fig. 6)
The mandrel collector is used to collect the rest
mandrel. To open the the mandrel collector (X),
slide the release button (D) towards the nose
housing nut (C) and raise the cover (E).
To close the the mandrel collector (X), lower the
cover (E) until the release button (D) clicks into
place.
Mounting the nosepiece (fig. 7)
Select the correct nosepiece for the rivet to be
installed Ref. Nose Piece chat.
Tighten the nosepiece into the front sleeve. (B) by
turning it clockwise using 11 mm spanner.
Mounting the jaw pusher and Tail guide(fig. 5)
Select the correct jaw pusher or jaw pusher
assembly (T) and Tail guide (Z) that matches
the Nose Piece selected. Ref. Nose Piece chart.
Put the tail guide (Z) into Spindle (AD) in SA
gear housing (AE) and tighten Pulling head assembly
(AC) counterclockwise using 24 mm spanner.
(Ref. fig5)
Insert small tube diameter into jaw pusher spring.
Reassemble jaw set (S) and jaw case (R) onto pulling
head (V).
Note: Avoid spanners to mount jaw case (R) onto
Pulling head (V). Jaw case (R) manual tightening
is enough to lock jaw case (R) onto Jaw case lock (W).
E N G L I S H
P s o t i o i n
M a n r d l e C l o e l t c o i n
13