Table of Contents
Advertisement
EN 16
5.
EL1.1U
•
To easily identify the used software version.
•
To view operation hours.
•
To display (or clear) the error code buffer.
How to Activate SAM
Via a standard RC transmitter: key in the code "062596"
directly followed by the "INFO" button. After activating SAM
with this method a service warning will appear on the screen,
you can continue by pressing the red button on the RC.
Contents of SAM:
•
Hardware Info.
–
A. VIPER SW Version. Displays the software version
of the VIPER software (main software) (example:
EL23U-1.2.3.4_12345 = AAAAB_X.Y.W.Z_NNNNN).
•
AAAA= the chassis name.
•
B= the region: A= AP, E= EU, L= Latam, U = US.
•
X.Y.W.Z= the software version, where X is the
main version number (different numbers are not
compatible with one another) and Y is the sub
version number (a higher number is always
compatible with a lower number). The last two
digits are used for development reasons only, so
they will always be zero in official releases.
•
NNNNN= last five digits of 12nc code of the
software.
–
B. SBY PROC Version. Displays the software version
of the stand-by processor.
–
C. Production Code. Displays the production code of
the TV, this is the serial number as printed on the back
of the TV set. Note that if an NVM is replaced or is
initialized after corruption, this production code has to
be re-written to NVM. ComPair will foresee in a
possibility to do this.
•
Operation Hours. Displays the accumulated total of
operation hours (not the stand-by hours). Every time the
TV is switched "on/off", 0.5 hours is added to this number.
•
Errors. (Followed by maximal 10 errors). The most recent
error is displayed at the upper left (for an error explanation
see paragraph "Error Codes").
•
Defective Module. Here the module that generates the
error is displayed. If there are multiple errors in the buffer,
which are not all generated by a single module, there is
probably another defect. It will then display the message
"UNKNOWN" here.
•
Reset Error Buffer. When you press "cursor right" and
then the "OK" button, the error buffer is reset.
•
Alignments. This will activate the "ALIGNMENTS" sub-
menu.
•
Dealer Options. Extra features for the dealers.
•
Options. Extra features for Service.
•
Initialise NVM. When an NVM was corrupted (or replaced)
in the former EMG based chassis, the microprocessor
replaces the content with default data (to assure that the
set can operate). However, all preferences and alignment
values are gone now, and option numbers are not correct.
Therefore, this was a very drastic way. In this chassis, the
procedure is implemented in another way: The moment the
processor recognizes a corrupted NVM, the "initialize
NVM" line will be highlighted. Now, you can do two things
(dependent of the service instructions at that moment):
–
Save the content of the NVM via ComPair for
development analysis, before initializing. This will give
the Service department an extra possibility for
diagnosis (e.g. when Development asks for this).
–
Initialize the NVM (same as in the past, however now it
happens conscious).
Note: When you have a corrupted NVM, or you have replaced
the NVM, there is a high possibility that you will not have picture
any more because your display option is not correct. So, before
you can initialize your NVM via the SAM, you need to have a
picture and therefore you need the correct display option. To
Service Modes, Error Codes, and Fault Finding
adapt this option, use ComPair. The correct HEX values for the
options can be found in the table below.
Table 5-2 Display option code overview (all FTV chassis)
Displ. Option HEX Display Type
000
00
PDP SDI
001
01
PDP SDI
002
02
PDP FHP
003
03
LCD LPL
004
04
LCD LPL
005
05
LCD LPL
006
06
SHARP
007
07
PDP SDI V3
008
08
PDP FHP 1024i 37"
009
09
LCOS XION
010
0A
LCD AUO
011
0B
LCD LPL
012
0C
LCD AUO
013
0D
LCD SHARP
014
0E
LCD LPL
015
0F
PDP SDI
016
10
PDP FHP
017
11
PDP FHP
018
12
PDP FHP
019
13
LCOS VENUS
020
14
LCOS VENUS
021
15
LCD LPL
022
16
LCD LPL
023
17
LG SD
024
18
PDP SDI V4
025
19
PDP SDI V4
026
1A
PDP FHP A2
027
1B
PDP SDI HD V4 50"
028
1C
LCD Sharp
029
1D
LCD AUO
030
1E
LCD Sharp
031
1F
LCD Sharp
032
20
LCD LPL
033
21
LCD QDI
034
22
ECO PTV
035
23
ECO PTV
036
24
ECO PTV
037
25
PDP FHP A3
038
26
DLP
039
27
DLP
040
28
LCD Sharp
041
29
LCD Sharp
042
2A
PDP SDI V4
043
2B
LCD Sharp
044
2C
LCD Sharp
045
2D
LCD LPL
•
Store. All options and alignments are stored when
pressing "cursor right" and then the "OK"-button
•
SW Maintenance.
–
SW Events. Not useful for service purposes. In case of
specific software problems, the development
department can ask for this info.
–
HW Events. Not functional at the moment this manual
is released, description will be published in an update
manual if the function becomes available.
How to Navigate
•
In SAM, you can select the menu items with the "CURSOR
UP/DOWN" key on the RC-transmitter. The selected item
will be highlighted. When not all menu items fit on the
screen, move the "CURSOR UP/DOWN" key to display the
next/previous menu items.
Size Vert. Resolution
42"
768p
50"
768p
42"
1024i
30"
768p
37"
768p
42"
768p
32"
768p
42"
480p
1024i
-
720p
30"
768p
32"
768p
32"
768p
37"
768p
42"
1080p
37"
480p
37"
1080i
42"
1080i
55"
768p
-
720p
-
1080p
26"
768p
32"
768p
42"
480p
42"
480p
42"
768p
42"
1024i
768p
37"
1080p
32"
768p
37"
1080p
37"
1080p
20"
768p
23"
768p
51"
1080i
55"
1080i
61"
1080i
42"
1024i
50"
720p
60"
720p
32"
768p
32"
768p
63"
768p
37"
768p
37"
768p
26"
768p
Advertisement
Table of Contents
