All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, or otherwise without the prior permission of Philips. Published by WO 0271 Service PaCE...
EN 2 EM5A P/M Technical Specifications, Connections and Chassis Overview 1. Technical Specifications, Connections and Chassis Overview Technical Specifications Rear Connections 1.1.1 Reception AUDIO AUDIO Tuning system : PLL Color systems (off-air) : NTSC M (3.58 - 4.5) : PAL B/G, PAL B/G...
Page 3
Technical Specifications, Connections and Chassis Overview EM5A P/M EN 3 Chassis Overview TOP CONTROL PANEL CRT PANEL SIDE I/O PANEL SMALL SIGNAL BOARD JACK HIGH DEFINITION INTERFACE MAINSWITCH PANEL AUTO-SCAVEM LARGE SIGNAL PANEL DC-SHIFT (optional) DAF PANEL PIP/DOUBLE WINDOW PANEL (optional) CL 26532079_001.eps...
• Safety components, indicated by the symbol , must be replaced with original Philips components. • Wear safety goggles when you replace the CRT. Safety regulations require that after a repair, you must return the set in its original condition. Pay particular attention to the following points: •...
Page 5
Safety and Maintenance Instructions, Warnings, and Notes EM5A P/M EN 5 Figure 2-2 Dolby Pro Logic Symbol. 2.4.2 Practical Service Precautions • It makes sense to avoid exposure to electrical shock. While some sources are expected to have a possible dangerous impact, others of quite high potential are of limited current and are sometimes held in less regard.
Mechanical Instructions EM5A P/M EN 17 4. Mechanical Instructions Index of this chapter: There is no problem when the subwoofer is disconnected 1. Service Connector (for ComPair) before operation, but a change from connected to 2. Set Disassembly disconnected during operation can damage the amplifier.
Page 18
EN 18 EM5A P/M Mechanical Instructions To access the SSB test points, do the following: To better access the component side of the LSP, do the following (see figure above): 1. Remove the LSP bracket from the bottom tray by pulling it backwards.
Page 19
Mechanical Instructions EM5A P/M EN 19 4.4.2 Side-I/O Assembly and Panel S S B CL 16532149_069.eps CL 26532041_069.eps 061201 110402 Figure 4-9 Side I/O assembly Figure 4-7 SSB removal (part 3) 1. Once you have taken out the SSB, remove the shieldings 1.
Page 20
EN 20 EM5A P/M Mechanical Instructions 4.4.4 DAF Assembly/Panel This panel is placed in a bracket that is located on the left side of the tuner. To remove the bracket: 1. Pull the release handle [1] backwards. This will lift the release catch, and the bracket can be pulled out backwards.
Service Default Mode (SDM) and Service Alignment Mode (SAM) offer several features for the service technician, while 5.2.2 Service Alignment Mode (SAM) the Customer Service Mode (CSM) is used for communication between a Philips Customer Care Centre (P3C) and a customer. Purpose • To perform (software) alignments.
Page 22
This will give as the built-in diagnose software has detected an error the the Philips Service department an extra possibility for buffer is adapted. The last occurred error is displayed on diagnosis (e.g. when Development asks for this).
Page 23
Service Modes, Error Codes and Fault Finding EM5A P/M EN 23 the 'CURSOR LEFT' and 'CURSOR RIGHT' keys on the • ‘Tuned bit’ Gives information about the tuning method of RC-transmitter after pressing the 'MENU' button and the stored pre-set. If a channel is found via 'automatic selecting 'SOUND' and 'HEADPHONE VOLUME'.
Page 24
7 is low (< 10) or the value of line 8 is low (< 10), increase the 'Brightness' or the 'Contrast' value. ComPair (Computer Aided Repair) is a service tool for Philips Consumer Electronics products. ComPair is a further...
Page 25
Service Modes, Error Codes and Fault Finding EM5A P/M EN 25 • Up- or downloading of pre-sets. Table 5-2 Stepwise shut-down table • Managing of pre-set lists. • Emulation of the Dealer Service Tool (DST). State Description mode Display LED Disabled •...
Page 26
EN 26 EM5A P/M Service Modes, Error Codes and Fault Finding • ComPair32 CD (update): 3122 785 60070. 5.5.3 How to clear the Error Buffer • SearchMan32 CD (update): 3122 785 60080. • ComPair interface cable: 3122 785 90004. Use one of the following methods: •...
Page 27
Service Modes, Error Codes and Fault Finding EM5A P/M EN 27 Blinking LED Procedure • The Service Default Mode (SDM). Start-up of the set in a predefined way. • The Service Alignment Mode (SAM). In this mode, items 5.6.1 Introduction of the set can be adjusted via a menu and with the help of test patterns.
EN 28 EM5A P/M Service Modes, Error Codes and Fault Finding NVM, and Tuner are initialised again, to ensure the normal diagram A6) will put the IC7700 in Standby mode (via tri- picture and sound conditions of the set. state input pin 6).
Page 29
Service Modes, Error Codes and Fault Finding EM5A P/M EN 29 6. When you switch “off” the set, this is done in a controlled More detailed way: way via the POR signal [3]. 1. Replace FET 7504 and zener 6505.
EN 30 EM5A P/M Service Modes, Error Codes and Fault Finding Phenomenon Possible Cause Repair tip No picture, red LED blinking No communication on slow As processor cannot communicate with one of the 2 busses the standby- with code 6-6-6 or 18-18-18.
Page 31
Wiring Diagram, Block Diagrams and Overviews EM5A P/M 6. Wiring Diagram, Block Diagrams and Overviews Wiring Diagram CENTRE DEGAUSSING COIL DEGAUSSING COIL SPEAKER TOP CONTROL PANEL AQUADAG AQUADAG TWEETER 16:9 ROTATION BLACK BLACK/ 1346 COIL WHITE (COMPONENT VIEW) A (LOT)
Page 32
Wiring Diagram, Block Diagrams and Overviews EM5A P/M Block Diagram Supply and Deflection SUPPLY DEFLECTION 1419 MAINS SWITCH MAIN SUPPLY LINE DEFLECTION DC-SHIFT (OPTIONAL) PANEL 1430 (PARTLY) 3550 SHIFT 400 mA CIRCUIT 1417 1417 1418 5502 5511 LINE 5503 5516...
Page 33
Wiring Diagram, Block Diagrams and Overviews EM5A P/M Block Diagram Video VIDEO TUNER, IF, I/O PICNIC FROM SIM CONN. SIM CONN. MAIN SIMM-CONNECTOR CONN. VIDEOPROC. CVBS-TXT BLOCK DIAGRAM (FEMALE) (MALE) (HIP) 'CONROL' 1205 1000 7307 CONTROL 7320 TDA9181 7412 7402...
Page 46
Circuit Diagrams and PWB Layouts EM5A P/M Large Signal Panel: Receiver Large Signal Panel: Front 1950 A1 2900 B2 3900 A3 3901 B3 3902 C3 6900 B3 FRONT RECEIVER 1945 E3 1947 1946 B2 9978 1947 A2 A8-27 1949 B2...
Page 47
Circuit Diagrams and PWB Layouts EM5A P/M Large Signal Panel: Inputs/Outputs 1900-A B1 3961 D3 1900-B B1 3962 D2 INPUTS/OUTPUTS 1900-C B1 3963 E3 1900-D F1 3964 E2 SVHS-IN: 1900-E F1 3965 F2 5900 +8VS 1900-F C1 3966 F2 SEL-SVHS-RR_STATUS2...
Page 48
Circuit Diagrams and PWB Layouts EM5A P/M Large Signal Panel: Diversity Tables Main supply [A1] Main supply [A1] Standby supply [A2] Line deflection [A3] Frame deflection E/W drive [A4] Audio amplifier [A6] Item DESCRIPTION Item DESCRIPTION Item DESCRIPTION Item DESCRIPTION...
Page 49
Circuit Diagrams and PWB Layouts EM5A P/M Layout Large Signal Panel (Top Side) CL 26532067_007.eps 050602...
Page 50
Circuit Diagrams and PWB Layouts EM5A P/M Large Signal Panel: Mapping Top Side Large Signal Panel: Mapping Bottom Side 0042 C8 2460 A10 3462 C9 5463 C9 7682 G1 9906 G10 2103 D9 2742 E4 3407 D3 3686 G10 3990 F1...
Page 51
Circuit Diagrams and PWB Layouts EM5A P/M Layout Large Signal Panel (Overview Bottom Side) Part 2 CL 26532067_08b.eps Part 1 CL 26532067_08a.eps Part 4 CL 26532067_08d.eps Part 3 CL 26532067_08c.eps CL 26532067_008.eps 300502...
Page 52
Circuit Diagrams and PWB Layouts EM5A P/M Layout Large Signal Panel (Part 1 Bottom Side) CL 26532067_08a.eps 300502...
Page 53
Circuit Diagrams and PWB Layouts EM5A P/M Layout Large Signal Panel (Part 2 Bottom Side) CL 26532067_08b.eps 300502...
Page 54
Circuit Diagrams and PWB Layouts EM5A P/M Layout Large Signal Panel (Part 3 Bottom Side) CL 26532067_08c.eps 300502...
Page 55
Circuit Diagrams and PWB Layouts EM5A P/M Layout Large Signal Panel (Part 4 Bottom Side) CL 26532067_08d.eps 300502...
Alignments EM5A P/M EN 107 8. Alignments Index of this chapter 1. General Alignment Conditions 2. Hardware Alignments 3. Software Alignments 4. Option Settings 1502 General Alignment Conditions 8.1.1 Start Conditions Warning All alignments Perform all electrical adjustments under the following...
Page 108
– Focus 2 (F2) = Dynamic alignment (red wire). Fixed setting: Pwl + 0% Focus method for Philips 32” tube with bleeder gun Luma gain You can recognize a CRT with bleeder gun by its type number: Fixed setting: 2.
Page 109
Alignments EM5A P/M EN 109 Table 8-1 OSD feedback of AFC alignment Table 8-2 Cathode parameter AFC-window AFC-frequency versus reference Light output (cd/mð) High 28" RF WS High 29" RF 4:3 32" RF WS 36" RF WS 1. The first item ('In' or 'Out') informs you whether you are in Table 8-3 White levels or out the AFC-window.
Page 110
EN 110 EM5A P/M Alignments V. S-correction Align for equal blocks on top, middle, and bottom of the picture tube. VERT. SLOPE Align 'V. S-correction' such that a block at the top (or bottom) of the picture has the same height as a block in the middle of the picture.
Page 111
Alignments EM5A P/M EN 111 Option Settings 8.4.1 Introduction The microprocessor communicates with a large number of I ICs in the set. To ensure good communication and to make digital diagnosis possible, the microprocessor has to know which ICs to address. The presence / absence of these specific ICs (or functions) is made known via the option codes.
Page 112
Set with Home Cinema Link (EU only) Set without Home Cinema Link Integrated RC Feature present. Feature not present. Tuner type Philips Set with Philips tuner. Alps Set with Alps tuner. 38.0 IF For AP PAL-multi set. For non AP PAL-multi sets Integrated DVD Feature present.
Page 113
Alignments EM5A P/M EN 113 8.4.3 Option numbers Select this sub-menu to set all options at once (expressed in two long numbers). An option number (or “option byte”) represents a number of different options. When you change these numbers directly, you can set all options very fast.
Page 114
16384 = On (EU) Integrated RC 0 = Off 32768 = On (EU) China IF 0 = Off Sum OB4 4 = On (AP-PAL) Tuner 0 = Philips / UV1361 8 = Alps / TEDE9 DVD-door lock 0 = Off 8192 = On...
Page 115
Alignments EM5A P/M EN 115 Table 8-7 Option bytes Group 2 Option name Settings(in decimal values) Auto Store Mode 0 = None (AP/USA) Sum OB5 2 = PDC/VPS 4 = TXT Page 6 = PDC/VPS/TXT Page 2CS Korea 0 = BTSC...
EN 116 EM5A P/M Circuit Descriptions and Abbreviation List 9. Circuit Descriptions and Abbreviation List Index of this chapter 1. Introduction 2. Block Diagram 3. Power Supply 4. Control 5. Tuner & IF 6. Video: HD Jack Interface 7. Video: High-end Input Processor 8.
Page 117
Circuit Descriptions and Abbreviation List EM5A P/M EN 117 Block Diagram PIP/DW MODULE TUNER BOCMA PIP/DW FILTER PROC. YUV50 UV13XX TDA932X SAA4978 TDA9178 TDA933X FRAMEDRIVE+ TUNER PICNIC TOPIC VERT FRAMEDRIVE- F-TYPE FILTER SYNC COMB D100 D100 HORZ FILTER VIDEO YUV_EAGLE...
Page 118
EN 118 EM5A P/M Circuit Descriptions and Abbreviation List The RGB amplifiers on the CRT-panel are supplied with 200 V to a damaged coil. When ignited, the current will be discharged from the LOT. via this spark gap. The Auto-SCAVEM circuit modulates transitions of the Resistor R3500 is used for limiting the inrush-current.
Page 119
Circuit Descriptions and Abbreviation List EM5A P/M EN 119 Implementation Power On Reset (POR) 2V5B 3V3_FBX COLD 5102 6103 20 ms 3120 5100/5101 -13V 2101 6111 +5V2 3748 3751 3103 2104 2114 3752 GND-STB .6 µP RESET 3110 7708 3105...
Page 120
EN 120 EM5A P/M Circuit Descriptions and Abbreviation List load. If the power supply is now loaded even more, the output voltage will decay. The maximum primary current set by R3108//3118 determines the maximum load. Vg-Q1 8V6 Stabilisation and Feedback...
Page 121
Circuit Descriptions and Abbreviation List EM5A P/M EN 121 The +33V is the tuning voltage for the Tuner. The +5VT is derived from the +8V with stabiliser 7912 (see diagram A8), and is used to supply the tuner only. SSB Supply There are several voltages going to the SSB: +8V6, +5V2 and +3V3.
Page 122
EN 122 EM5A P/M Circuit Descriptions and Abbreviation List If the load continues to increase, the regulator will block at a Control (Diagram B5) certain moment. T is now at maximum value. This is the point where V will go below 141 V and, at further increasing load, 7001 A0...A19...
Page 123
Circuit Descriptions and Abbreviation List EM5A P/M EN 123 The OTC will generate an error code to indicate what was The demodulated IF-video signal is available at pin 10 of the wrong. HIP. In this video signal, there is a rest of the sound carrier, which is filtered out by the sound trap 1407.
Page 124
EN 124 EM5A P/M Circuit Descriptions and Abbreviation List This RGB output of the board is signaled into the set (HOP- Audio section of SSB [B4].) Audio left and audio right are connected via the two cinches and passed through the module.
Page 125
Circuit Descriptions and Abbreviation List EM5A P/M EN 125 Video: Feature Box 7 (50 Hz signals) The objective for this chassis was, to reach a sharper picture In the Feature Box 7 (FBX7), a new IC is used, called the by means of a higher definition.
Page 126
EN 126 EM5A P/M Circuit Descriptions and Abbreviation List The 50 Hz YUV signals, coming from the HIP, are fed to the video is doubled by the FBX6. A 50/60 Hz frame frequency is PICNIC via an anti-aliasing filter. converted to 100/120 Hz. In addition, the line frequency (16 The (AABB) frame frequency doubling is done by the PICNIC kHz) is doubled (32 kHz).
Page 127
EM5A P/M EN 127 • Dynamic Contrast. To make the contrast (black/white) range wider, Philips has invented Dynamic Contrast. It Luminance Y uses the digital memory used in 100 Hz sets. It measures Original slope every A-field (25 x per second), and digitally analyses...
Page 128
EN 128 EM5A P/M Circuit Descriptions and Abbreviation List To obtain above shown filter characteristic, filters are set at 9.9.1 Introduction three parameters (see A, B, and C). In this way, only the higher frequencies are “lifted”. After sending the luminance signal...
Page 129
• Dynamic Contrast. To make the contrast (black/white) gain=8 range wider, Philips has invented Dynamic Contrast. It uses the digital memory used in 100 Hz sets. It measures gain=31 every A-field (25 x per second), and digitally analyses spatial X or Y where on the grayscale most of the image is located.
Page 130
EN 130 EM5A P/M Circuit Descriptions and Abbreviation List 2700 3700 Y100 Original samples 5700 detail Added interpolated samples 7728 1050 samples 7731 5739 Y-EAGLE CL 26532058_023.eps 110602 (pin54) Figure 9-20 Vertical LTI The principle for vertical LTI is the same as for horizontal LTI.
Page 131
Circuit Descriptions and Abbreviation List EM5A P/M EN 131 9.10.3 OSD/TXT Control Frame Rotation For frame rotation, a control voltage is used from pin 25 of the HOP. Frame rotation is only used in wide-screen sets. On pins 35 to 38, the RGB and fast blanking from the OTC (OSD and TXT) are inserted.
Page 132
EN 132 EM5A P/M Circuit Descriptions and Abbreviation List 9.12 Horizontal (Line) Deflection (Diagram A3) 9.12.1 Principle Linearity Correction Caused by serial losses in the line output stage COLD 141V 6408 MAIN SUPPLY +11D S-correction 5430 3409 STANDBY SUPPLY +5V2 X >...
Page 133
Circuit Descriptions and Abbreviation List EM5A P/M EN 133 • Period t1-t2: When TS7421 is driven into conductivity, the the deflection to slow down. In the centre, the voltage increases capacitor voltage of 141 V will be divided across bridge-coil and the deflection will be faster.
Page 134
EN 134 EM5A P/M Circuit Descriptions and Abbreviation List secondary winding. Via rectifying and smoothing, the several 9.13.3 Anti-moiré Circuit (Diagram B9) secondary supply voltages are generated, like: • EHT, Focus and Vg2-voltage Introduction • +200V for the CRT panel (pin 8 LOT) By shifting two following frames with respect to each other, it is •...
Page 135
Circuit Descriptions and Abbreviation List EM5A P/M EN 135 9.14.5 Audio Amplifier (Diagram A6) 7651 7770 The audio amplifier is an integrated class-D power amplifier IC, 17/18 MAIN IF MONO-IN DACA_L/R HEADPHONE the TDA7490. It delivers an output of 2 x 15 W...
Page 136
EN 136 EM5A P/M Circuit Descriptions and Abbreviation List Protection 9.16 CRT Panel / Rotation A loudspeaker DC protection is implemented. The amplifier IC TDA7490 has a “standby-mute-play” feature via the tri-state 9.16.1 RGB Amplifiers (Diagram F1) input pin 6. When the voltage on pin 6 is: •...
Page 137
Circuit Descriptions and Abbreviation List EM5A P/M EN 137 9.17.2 Normal Scavem Matrix and Differentiator MATRIX DIFFERENTIATOR Differen- Output Matrix Coring +12S tiator stage coil 11V8 7012 BFS20 2008 8V 7 BF824 coil 7008 7006 7010 BFS20 Y_SCAVEM BFS20 (FROM SSB)
Page 139
Circuit Descriptions and Abbreviation List EM5A P/M EN 139 and pin 94 (hor.) and the sub picture syncs are applied to pin 72 (vert.) and pin 87 (hor..) For DW mode, the main picture is compressed horizontally by a factor of two and fed directly to the output. After compression, 0205 a horizontal expansion of two is possible for the main picture.
EN 140 EM5A P/M Circuit Descriptions and Abbreviation List • Most algorithms are located in the embedded processor of AUDIO-SR Audio surround right the PICNIC, because of time-critical calculations, and AUDIO_SW Audio Subwoofer because most picture analysing and correction circuits are...
Page 141
Circuit Descriptions and Abbreviation List EM5A P/M EN 141 FILAMENT Filament of CRT Read Only Memory FLASH Flash memory Service Alignment Mode Field Memory or Frequency Sandcastle: two-level pulse derived Modulation from sync signals G-TXT Green teletext Short Circuit GND-DRIVE...
EN 142 EM5A P/M Circuit Descriptions and Abbreviation List 9.21 IC Data Sheets In this paragraph, the internal block diagrams and pinning are given of ICs that are drawn as a “black box” in the electrical diagrams (with the exception of “memory” and “logic” ICs).