Option And Peripheral Devices; Option List - Mitsubishi Electric FR-D700 Manual

Option and Peripheral Devices

Option list

By fitting the following options to the inverter, the inverter is provided with more functions.
Name
Parameter unit (8 languages)
Parameter unit with battery pack
Enclosure surface operation panel
Parameter unit connection cable
DIN rail attachment
AC reactor
DC reactor
EMC Directive compliant noise filter FR-E5NF
Radio noise filter
Line noise filter
Filter pack
Brake resistor
High-duty brake resistor
Brake unit
Resistor unit
Discharging resistor
Power regeneration common
converter
Stand-alone reactor dedicated for
the FR-CV
High power factor converter
Surge voltage suppression filter
Manual controller
DC tach. follower
Three speed selector
Motorized speed setter
Ratio setter
Speed detector
Master controller
Soft starter
Deviation detector
Preamplifier
Pilot generator
Deviation sensor
Frequency setting potentiometer
Analog frequency meter
(64mm × 60mm)
Calibration resistor
FR Configurator SW3(VFD setup
software)
∗ Rated power consumption. The power supply specifications of the FR series manual controllers and speed controllers are 200VAC 50Hz, 220V/220VAC 60Hz,
and 115VAC 60Hz.
Type
FR-PU07
Interactive parameter unit with LCD display
FR-PU04
This parameter unit enables parameter setting without connecting the inverter
FR-PU07BB(-L)
to power supply.
This operation panel enables inverter operation and monitoring of frequency,
FR-PA07
etc. from the enclosure surface
Cable for connection of operation panel or parameter unit
FR-CB20
indicates a cable length. (1m, 3m, 5m)
FR-UDA01 to 03 Attachment for installation on DIN rail
For harmonic current reduction and inverter input power factor improvement
FR-HAL
(total power factor approx. 88%)
For harmonic current reduction and inverter input power factor improvement
FR-HEL
(total power factor approx. 93%)
EMC Directive (EN61800-3 C3) compliant noise filter
FR-BIF(H) For radio noise reduction (connect to the input side)
FR- BSF01
For line noise reduction
FR- BLF
Combination of power factor improving DC reactor, zero phase reactor, and
FR-BFP2
capacitative filter
MRS type,
For increasing the regenerative braking capability (permissible duty 3%/6%ED)
MYS type
For increasing the regenerative braking capability (permissible duty 10%/
FR-ABR
6%ED)
For increasing the braking capability of the inverter (for high-inertia load or
FR-BU2
negative load)
FR-BR
Brake unit, electrical-discharge resistor and resistor unit are used in
GZG, GRZG type
combination
FR-CV Unit which can return motor-generated braking energy back to the power
FR-CVL supply in common converter system
The high power factor converter switches the converter section on/off to
FR-HC reshape an input current waveform into a sine wave, greatly suppressing
harmonics. (Used in combination with the standard accessory.)
FR-ASF
Filter for suppressing surge voltage on motor
FR-BMF
For independent operation. With frequency meter, frequency potentiometer and
FR-AX
start switch.
FR-AL For synchronous operation (1.5VA) by external signal (0 to 5V, 0 to 10V DC)∗
For three speed switching, among high, middle and low speed operation
FR-AT
(1.5VA)∗
For remote operation. Allows operation to be controlled from several places
FR-FK
(5VA)∗
FR-FH For ratio operation. The ratios of five inverters can be set (3VA)∗
FR-FP For tracking operation by a pilot generator (PG) signal (3VA)∗
Master controller (5VA) for parallel operation of multiple (maximum 35)
FR-FG
inverters.∗
For soft start and stop. Enables acceleration/deceleration in parallel operation
FR-FC
(3VA)∗
For continuous speed control operation. Used in combination with a deviation
FR-FD
sensor or synchro (5VA)∗
FR-FA Used as an A/V converter or arithmetic amplifier (3VA)∗
QVAH-10 For tracking operation. 70V/35VAC 500Hz (at 2500r/min)
For continuous speed control operation (mechanical deviation detection)
YVGC-500W-NS
Output 90VAC/90ºC
WA2W 1kΩ For frequency setting. Wire-wound 2W 1kΩ type B characteristic
Dedicated frequency meter (graduated to 120Hz). Moving-coil type DC
YM206NRI 1mA
ammeter
RV24YN 10kΩ For frequency meter calibration. Carbon film type B characteristic
FR-SW3-SETUP-
Supports an inverter startup to maintenance.
WE
Applications, Specifications, etc.
Applicable
Inverter
Shared among
all models
Shared among
all models
(Available soon)
Shared among
all models
Compatible with
the 3.7K or less
According to
capacities
400V: According
to capacities
Shared among
all models
Three-phase
power input
model:
compatible with
0.4K or bigger
capacity
200V: For the
0.4K or more
For the 0.4K or
more
According to
capacities
400V: According
to capacities
400V: For the
5.5K or more
Shared among
all models
Shared among
all models
24