Champion Power Equipment 100310 Operator's Manual
  1. Manuals
  2. Brands
  3. Champion Power Equipment Manuals
  4. Pressure Washer
  5. 100310
  6. Operator's manual

Champion Power Equipment 100310 Operator's Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

OPERATOR'S MANUAL
MODEL #100310
3000 PSI PRESSURE WASHER
or visit championpowerequipment.com
READ AND SAVE THIS MANUAL. This manual contains important safety precautions which should be read and understood before operating the product.
Failure to do so could result in serious injury. This manual should remain with the product.
Specifications, descriptions and illustrations in this manual are as accurate as known at the time of publication, but are subject to change without notice.
Made in China - REV 20170215
Champion Power Equipment, Inc., Santa Fe Springs, CA USA

Advertisement

Table of Contents
loading

Related Manuals for Champion Power Equipment 100310

Summary of Contents for Champion Power Equipment 100310

  • Page 1 Failure to do so could result in serious injury. This manual should remain with the product. Specifications, descriptions and illustrations in this manual are as accurate as known at the time of publication, but are subject to change without notice. Made in China - REV 20170215 Champion Power Equipment, Inc., Santa Fe Springs, CA USA...

  • Page 2: Table Of Contents

    TABLE OF CONTENTS 100310 - 3000 PSI PRESSURE WASHER TABLE OF CONTENTS Storage ............

  • Page 3: Introduction

    INTRODUCTION 100310 - 3000 PSI PRESSURE WASHER INTRODUCTION SAFETY DEFINITIONS Congratulations on your purchase of a Champion Power The purpose of safety symbols is to attract your attention to Equipment (CPE) product. CPE designs, builds, and supports possible dangers. The safety symbols, and their explanations, all of our products to strict specifications and guidelines.

  • Page 4: Safety Symbols

    SAFETY SYMBOLS 100310 - 3000 PSI PRESSURE WASHER SAFETY SYMBOLS Some of the following symbols may be used on this product. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to more safely operate the product.

  • Page 5: Important Safety Instructions

    IMPORTANT SAFETY INSTRUCTIONS 100310 - 3000 PSI PRESSURE WASHER IMPORTANT SAFETY INSTRUCTIONS WARNING Sparks can result in fire or electrical shock. WARNING When servicing the pressure washer: The engine exhaust from this product contains chemicals known to the State of California to cause cancer and birth Disconnect the spark plug wire and place it where it cannot defects and other reproductive harm.
  • Page 6 IMPORTANT SAFETY INSTRUCTIONS 100310 - 3000 PSI PRESSURE WASHER WARNING NOTICE NEVER spray flammable liquids or use pressure washer in Improper treatment or use of the pressure washer can areas containing combustible dust, liquids, or vapor. damage it, shorten its life and void your warranty.
  • Page 7 IMPORTANT SAFETY INSTRUCTIONS 100310 - 3000 PSI PRESSURE WASHER WARNING DANGER Use of pressure washers can create wet walking surfaces. Fuel and fuel vapors are highly flammable and extremely While using a pressure washer, forces from the gun can explosive.

  • Page 8: Controls And Features

    CONTROLS AND FEATURES 100310 - 3000 PSI PRESSURE WASHER CONTROLS AND FEATURES Read this operator’s manual before operating your pressure washer. Familiarize yourself with the location and function of the controls and features. Save this manual for future reference. 1. Nozzles 11.

  • Page 9: Parts Included

    ASSEMBLY 100310 - 3000 PSI PRESSURE WASHER ASSEMBLY Parts Included Gun Assembly Your pressure washer requires some assembly. This unit ships from our factory without oil. It must be properly serviced Spray Wand (A)..............1 with fuel and oil before operation. If you have any questions Trigger Gun (B) ..............

  • Page 10: Add Engine Oil

    ASSEMBLY 100310 - 3000 PSI PRESSURE WASHER Add Engine Oil Degrees Celsiusº (Outside) CAUTION Full Synthetic 5W-30 DO NOT attempt to crank or start the engine before it has been properly filled with the recommended type and amount of oil. Damage to the pressure washer as a result of failure to follow these instructions will void your warranty.

  • Page 11: Add Fuel

    ASSEMBLY 100310 - 3000 PSI PRESSURE WASHER Add Fuel NOTICE 1. Use clean, fresh, regular unleaded fuel with a minimum Our engines work well with 10% or less ethanol blend fuels. octane rating of 85 and an ethanol content of less than When using blended fuels there are some issues worth 10% by volume.

  • Page 12: Connect The High Pressure Hose

    ASSEMBLY 100310 - 3000 PSI PRESSURE WASHER Connect the High Pressure Hose 2. With the hose faucet turned completely off, attach the end of the garden hose to the water inlet. Tighten by hand. 1. Completely uncoil and straighten the high pressure hose to prevent kinks.

  • Page 13: Operation

    OPERATION 100310 - 3000 PSI PRESSURE WASHER OPERATION NOTICE Keep choke lever in “CHOKE” position for 2 pulls of the Pressure Washer Location recoil starter. After second pull, move choke lever to the This pressure washer must have at least 1.5 m (5 ft.) of “RUN”...

  • Page 14: High Pressure Wash

    OPERATION 100310 - 3000 PSI PRESSURE WASHER Use the following table to determine which nozzle to use. NOZZLE SELECTION GUIDE LOW PRESSURE 0° 25° 40° Soap HIGH PRESSURE WASH WASH 0° 25° 40° Soap Abrasive Gentle Concrete, Brick, Masonry Siding, Gutters, Home...

  • Page 15: System Flush

    OPERATION 100310 - 3000 PSI PRESSURE WASHER System Flush are customized for pressure washer use on specific cleaning tasks. Pressure washer detergents are as thick as water. After using detergents, flush the suction system by placing the Using thicker detergents – like dish soap – will clog the detergent suction tube into a bucket of clean water.

  • Page 16: Stopping The Engine

    To alleviate high altitude issues other than the natural power The owner/operator is responsible for all periodic maintenance. loss, Champion Power Equipment can provide a high altitude Complete all scheduled maintenance in a timely manner. carburetor main jet. The alternative main jet and installation instructions can be obtained by contacting Customer Support.

  • Page 17: Cleaning The Pressure Washer

    MAINTENANCE 100310 - 3000 PSI PRESSURE WASHER Cleaning the Pressure Washer 5. Add up to 0.6 L (0.6 qt.) of oil and replace oil fill cap/ dipstick. DO NOT OVERFILL. CAUTION 6. Dispose of used oil at an approved waste management facility.

  • Page 18: Cleaning The Spark Arrester

    Service your pressure washer more frequently when operating spark arrester. in adverse conditions. Contact our help line at 1-877-338-0999 to locate the nearest Champion Power Equipment certified 2. Remove the four (4) screws holding the cover plate which service dealer for your maintenance needs.

  • Page 19: Engine Stored For Less Than 30 Days

    STORAGE 100310 - 3000 PSI PRESSURE WASHER 3. Clean the pressure washer according to the instructions in 5. Pour the antifreeze into the funnel, then pull on the engine the Maintenance section. recoil starter to create suction in the pump housing. Pull the recoil several times until antifreeze comes out of the 4.

  • Page 20: Specifications

    Start Type ..............Manual Important Message About Temperature Oil Specifications Your Champion Power Equipment product is designed and rated DO NOT OVERFILL. for continuous operation at ambient temperatures up to 40°C Type ..........

  • Page 21: Parts Diagram

    SPECIFICATIONS 100310 - 3000 PSI PRESSURE WASHER Parts Diagram...

  • Page 22: Parts List

    SPECIFICATIONS 100310 - 3000 PSI PRESSURE WASHER Parts List Part Number Description Qty. Part Number Description Qty. 22 254.201600.00.78 26.111 Engine Mounting Plate 23 1.5789.0615 Flange Bolt M6 x 15 Key, SQ 2.14.001 4.78 x 4.78 x 40 24 1.5789.0608 Flange Bolt M6 x 8 2.08.010...

  • Page 23: Engine Parts Diagram

    SPECIFICATIONS 100310 - 3000 PSI PRESSURE WASHER Engine Parts Diagram...

  • Page 24: Engine Parts List

    SPECIFICATIONS 100310 - 3000 PSI PRESSURE WASHER Engine Parts List Part Number Description Qty. Part Number Description Qty. 1.5789.0608 Flange Bolt M6 x 8 Oil Dipstick Assembly, 36 22.031000.00.48 Yellow Cover, Recoil Starter, 22.061100.00.2 37 24.030007.00 Cover, Crankcase Black 38 1.5789.0832.0.8 Flange Bolt M8 x 32 21.061005.00...
  • Page 25 SPECIFICATIONS 100310 - 3000 PSI PRESSURE WASHER Part Number Description Qty. Part Number Description Qty. 21.040008.00 Rotator, Exhaust Valve Screw Cap, Air Clean 115 24.091600.01 Cover 75 24.040202.00 Shaft, Rocker Arm 116 2.12.001 Buffer Ø7.5 x 7.5 76 22.040009.00 Rocker Arm 117 2.06.006...

  • Page 26: Troubleshooting

    SPECIFICATIONS 100310 - 3000 PSI PRESSURE WASHER Troubleshooting Problem Cause Solution No fuel. Add fuel. Pressure washer will not start. Faulty spark plug. Replace spark plug. Fill crankcase to the proper level. Place Pressure washer will not start; Low oil level.

  • Page 27: Other Exclusions

    Warranty Qualifications – Failures due to acts of God and other force majeure events Champion Power Equipment (CPE) will register this warranty upon beyond the manufacturer’s control. receipt of your Warranty Registration Card and a copy of your sales –...
  • Page 28 Champion Power Equipment, Inc (CPE) and Environment and Climate Change Canada (ECCC) Emission Control System Warranty Your Champion Power Equipment (CPE) engine complies with Environment and Climate Change Canada (ECCC) emission regulations. YOUR WARRANTY RIGHTS AND OBLIGATIONS: CPE is pleased to explain the Emission Control Systems Warranty on your 2017 small off-road engine.
  • Page 29 EMISSION CONTROL SYSTEM WARRANTY The following are specific provisions relative to your Emission Control System Warranty Coverage. Emission Control System Warranty (ECS Warranty): 1. APPLICABILITY: The ECS Warranty Period shall begin on the date the new engine or equipment is delivered to its original, end-use purchaser, and shall continue for 24 consecutive months thereafter.
  • Page 30 Champion Power Equipment dealer who is authorized by Champion Power Equipment, Inc. to sell and service that CPE product during his normal business hours. Claims for repair or adjustment found to be caused solely by defects in material or workmanship will not be denied because the engine was not properly maintained and used.

Table of Contents