Introduction Introduction Accessories Champion Power Equipment manufactures Congratulations on your purchase of a and sells accessories designed to help you Champion Power Equipment pressure get the most from your purchase. To find out washer. CPE designs and builds pressure more about our accessories, please visit our washers to strict specifications.
Manual Conventions CAUTION Manual Conventions CAUTION indicates a potentially hazardous This manual uses the following symbols to situation which, if not avoided, result in help differentiate between different kinds of minor or moderate injury. information. The safety symbol is used with a key word to alert you to potential hazards in operating and owning power equipment.
Safety Rules WARNING Safety Rules Sparks can result in fire or electrical shock. When servicing the pressure washer: WARNING Disconnect the spark plug wire and place it where it cannot contact the plug. Read this manual thoroughly before operating DO NOT check for spark with the plug removed. your pressure washer.
Page 7
Safety Rules DANGER CAUTION Fuel and fuel vapors are highly flammable and Improper treatment or use of the pressure extremely explosive. washer can damage it, shorten its life and void Fire or explosion can cause severe burns or your warranty. death.
Page 8
Safety Rules WARNING NEVER run the unit dry. Be sure the water supply is completely turned on before operating the unit. WARNING If water has frozen in the pressure washer, thaw the pressure washer in a warm room before starting. DO NOT pour hot water on or into the pump;...
Controls and Features Controls and Features Read this owner’s manual before operating your pressure washer. Familiarize yourself with the location and function of the controls and features. Save this manual for future reference. Pressure Washer High Pressure Pump (1) – gas-engine Recoil Starter (6) –...
Assembly Install the Support Leg Assembly Attach each rubber vibration mount to the base frame with a cap screw Your pressure washer requires some (M8x20) and lock nut (M8). assembly. This unit ships from our factory 2. Tip the pressure washer slowly so that it without oil.
Assembly Add Fuel Install the Hoses Use clean, fresh, regular unleaded fuel with a minimum octane rating of 85. 2. DO NOT mix oil with fuel. Attach the Pressure Gun 3. Clean the area around the fuel cap. Attach the wand with nozzle to the gun. 4.
Operation Operation High Pressure Wash CAUTION Pressure Washer Location This pressure washer must have at least five Always engage the trigger safety latch when the feet of clearance from combustible material. unit is not in use. Leave at least three feet of clearance on all sides of the pressure washer to allow for The trigger safety latch prevents the gun from adequate cooling, maintenance and...
Operation Before triggering the gun, adjust the CAUTION nozzle or quick connect tip to a wide fan pattern. 3. Place the nozzle approximately 4-5 feet Never make the nozzle pressure adjustment away from the cleaning surface. Then when the gun is triggered. hold the nozzle at a 45 degree angle to the cleaning surface.
Operation CAUTION Operating Tips Release the trigger prior to switching the wand CAUTION between high and low pressure. Failure to do so may reduce the life of the o-rings Never operate your pressure washer without in the wand and will void your warranty. water.
Maintenance Maintenance The owner/operator is responsible for all periodic maintenance. WARNING Spark Plugs Never operate a damaged or defective pressure washer. Remove the spark plug cable from the spark plug. 2. Use the spark plug tool that shipped with your pressure washer to remove the plug.
Maintenance Adjustments Pressure Washer CPE recommends that you contact our service line at 1-877-338-0999 for all other Maintenance service and/or adjustment needs. Make certain that the pressure washer is kept clean and stored properly. Only operate Maintenance Schedule the unit on a flat, level surface in a clean, dry operating environment.
Storage 6. Remove the spark plug and pour about ½ ounce of oil into the cylinder. Crank Storage the engine slowly to distribute the oil and lubricate the cylinder. For long term storage, please follow these 7. Reattach the spark plug. guidelines.
Specifications Specifications Spark Plugs Your pressure washer comes equipped with a ¾” long reach plug (18mm) Engine Specifications Intermittent use (less than 1 hour/month) or Engine 6.5 HP OHV CPE EPA & CARB certified colder temperatures (below 60°F) NGK B6ES or equivalent NOTE Moderate use (less than 3 hours/month) or seasonal temperatures (50-80°F)
Specifications Pressure Washer Parts List Item Part Number Description Qty. ST29QXG-310-0001 Spring Plate ST29QXG-310-0002 Piston Spring ST29QXG-310-0003 Oil Seal 15×24×6 ST29QXG-310-0004 Washer ST29QXG-310-0005 Seal Washer ST29QXG-310-0006 Packing Support ST29QXG-310-0007 O-Ring 21.2×1.8 ST29QXG-310-0008 Washer ST29QXG-310-0009 Water Seal ST29QXG-310-0010 Plunger ST29QXG-310-0011 Valve Spring ST29QXG-310-0012 Inlet Valve Core GB1667-S8-20...
Page 22
Specifications Item Part Number Description Qty. ST29QXG-310-0051 O-Ring 4×2.65 ST29QXG-310-0052 Manifold ST29QXG-310-0053 Pump Cover Seal Ring ST29QXG-310-0054 Plastic Knob ST29QXG-310-0055 Inlet Filter Gasket ST29QXG-310-0056 Inlet Connector 1 ST29QXG-310-0057 Plastic Gasket ST29QXG-310-0058 Pump Cover ST29QXG-310-0059 Temperature Soft Plug ST29QXG-310-0060 Chemical Hose ST29QXG-310-0061 Chemical Filter ST29QXG-310-0062...
Specifications Engine Parts List Item Part Number Description Qty. ST168F-107-0001 Clip ST168F-107-0002-000001 Tube ST168F-107-0003 Fuel Tank Joint ST168F-107-0004 Fuel Tank Cap ST168F-107-0005 Fuel Filter ST168F-107-0006-000100 Fuel Tank ST168F-111-0001 Throttle Return Spring ST168F-111-0002 Governor Spring ST160F-111-0003 Governor Arm GB41-N-6 Nut M6 ST160F-111-0004 Lock Pin ST160F-111-0005...
Page 25
Specifications Item Part Number Description Qty. ST168F-103-0007 Case Over Packing ST160F-103-0008-010100 Oil Filler Cap ST160F-103-0009 Oil Filler Cap Packing ST168F-103-0010-000100 Crankcase Cover GB5789-FB8-32 Flange Bolt 8×32 GB5789-FB6-8 Flange Bolt 6×8 ST160F-107-0007 Air Cleaner Cover Nut ST168F-107-0008-000100 Air Cleaner Cover ST168F-107-0009 Air Cleaner Element Washer ST168F-107-0010-000101 Air Cleaner Element...
Page 26
Specifications Item Part Number Description Qty. 103B ST168F-105-0012 Second Ring (Black) 103C ST168F-105-0013 Oil Ring Set ST168F-2-105-0014 Piston ST168F-105-0015 Piston Pin Clip ST168F-105-0016 Piston Pin ST168F-105-0017 Connecting Rod ST168F-104-0018 Tappet Lock Nut ST168F-104-0019 Exhaust Rocker Arm ST168F-104-0020 Tappet Adjusting Bolt ST168F-104-0021 Intake Rocker Arm ST168F-104-0022...
Troubleshooting Troubleshooting Problem Cause Solution Pressure washer will not start No fuel Add fuel Faulty spark plug Replace spark plug Unit loaded during start up Remove load from unit Pressure washer will not start; Low oil level Fill crankcase to the proper level Pressure washer starts but runs Place pressure washer on a flat, level roughly...
This warranty will not apply to parts and/or Warranty Qualifications labor if this pressure washer is deemed to Champion Power Equipment (CPE) will have been misused, neglected, involved in an register this warranty upon receipt of your accident, abused, loaded beyond the Warranty Registration Card and a copy of pressure washer’s limits, modified, installed...
Contact Information Address Champion Power Equipment, Inc. Customer Service 10006 Santa Fe Springs Rd. Santa Fe Springs, CA 90670 Customer Service Mon – Fri 8:30 AM – 5:00 PM (PST/PDT) Toll Free: 1-877-338-0999 Fax no.: 1-562-236-9429...
Page 30
The California Air Resources Board (CARB) and the United States Environment Protection Agency (U.S. EPA.) Emission Control System Warranty Your Champion Power Equipment (CPE) engine complies with both the U.S. EPA and state of California Air Resources Board (CARB) emission regulations. YOUR WARRANTY RIGHTS AND OBLIGATIONS: The California Air Resources Board, US EPA AND CPE are pleased to explain the Federal and California Emission Control Systems Warranty on your 2005 and later, small off-road engine.
Page 31
Warranty EMISSION CONTROL SYSTEM WARRANTY The following are specific provisions relative to your Emission Control System Warranty Coverage. Emission Control System Warranty (ECS Warranty) for 1995 and later model year California small off-road engines (for other states, 1997 and later model year engines): 1.
Page 32
Champion Power Equipment dealer who is authorized by Champion Power Equipment, Inc. to sell and service that CPE product during his normal business hours. Claims for repair or adjustment found to be caused solely by defects in material or workmanship will not be denied because the engine was not properly maintained and used.